| Age | Commit message (Collapse) | Author |
|---|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-imx
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/20228
- Convert imx8mp-beacon and verdin-imx8mm/verdin-imx8mp to OF_UPSTREAM.
- Enable PCIe NVMe support on imx8mp_beacon.
- Fix Ethernet and board detection on mx6cuboxi.
- Fix signature_block_hdr struct fields.
- Fix imx9_probe_mu prototype and make it to get called in
EVT_DM_POST_INIT_R.
- Test whether ethernet node is enabled before reading MAC EEPROM on
DHSOM SoMs.
|
|
https://source.denx.de/u-boot/custodians/u-boot-snapdragon
- Ethernet, i2c, and USB support are now enabled by default
- The clock driver gets some bug fixes and cleanup
- Invalid FDTs are now properly detected in board_fdt_blob_setup().
- The pinctrl driver gains preparatory support for per-pin function
muxes.
- Support is added for two generations of Qualcomm HighSpeed USB PHY
- A power domain driver is added for the Globall Distributed Switch
Controllers on the GCC hardware block.
- SDM845 gains USB host mode support.
- OF_LIVE is enabled by default for Qualcomm platforms
- Some U-Boot devicetree compatibility fixups are added during init to
improve compatbility with upstream DT.
|
|
https://source.denx.de/u-boot/custodians/u-boot-amlogic
- jethubj100: fix config, MAINTAINERS & update docs
- Switch GXL, GXM, AXG, G12A, G12B & SM1 to using upstream DT
|
|
- kirkwood: Switch to using upstream dts/dtsi files (Tony)
- mvebu: Turris Omnia - New board revision support (Marek)
|
|
|
|
According to the documentation (for example NXP's AN13994 on encrypted
boot on AHAB-enabled devices), the format of the signature block is:
+--------------+--------------+--------------+-------------+
| Tag | Length - msb | Length - lsb | Version |
+--------------+--------------+--------------+-------------+
| SRK Table offset | Certificate offset |
+-----------------------------+----------------------------+
| Blob offset | Signature offset |
+-----------------------------+----------------------------+
There is no runtime error in the current u-boot code. The only user of
struct signature_block_hdr is the "get_container_size" function in the
"arch/arm/mach-imx/image-container.c" file, and it's only using the very
first fields of the struct (which are in the correct position) and thus
there is no runtime failure.
On the other hand, extending the code to get the data encryption key
blob offset on the signature header gives a wrong value as the field is
in the wrong order.
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
|
|
Move verdin-imx8mm and verdin-imx8mp to OF_UPSTREAM:
- handle the fact that dtbs now have a 'freescale/' prefix
- imply OF_UPSTREAM
- remove redundant files from arch/arm/dts leaving only the
*-u-boot.dtsi files
- update MAINTAINERS files
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
|
|
This event callback imx9_probe_mu needs to be called in board_r
as well, because many ELE APIs depending on this MU probed
Signed-off-by: Ye Li <ye.li@nxp.com>
|
|
Since the event callback imx9_probe_mu is re-defined, update
its prototype.
Signed-off-by: Ye Li <ye.li@nxp.com>
|
|
The i.MX6 Cubox-i and HummingBoards can have different PHYs at varying
addresses. U-Boot needs to auto-detect which phy is actually present,
and at which address it is responding.
Auto-detection from multiple phy nodes specified in device-tree does not
currently work correct. As a work-around merge all three possible phys
into one node with the special address 0xffffffff which indicates to the
generic phy driver to probe all addresses.
Signed-off-by: Josua Mayer <josua@solid-run.com>
[fabio: Added the changes to imx6qdl-sr-som-u-boot.dtsi.]
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Christian Gmeiner <cgmeiner@igalia.com>
Tested-by: Christian Gmeiner <cgmeiner@igalia.com>
|
|
The mx6cuboxi_defconfig target supports several board
variants. All of these variants use the hummingboard devicetree in U-Boot.
Currently, the devicetree model as well as the board variant name
are shown:
...
Model: SolidRun HummingBoard2 Dual/Quad (1.5som+emmc)
Board: MX6 Cubox-i
...
Printing the devicetree model that is used internally by U-Boot
may confuse users.
Unselect the CONFIG_DISPLAY_BOARDINFO option so that only the
board name is printed in board_late_init() instead.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Christian Gmeiner <cgmeiner@igalia.com>
|
|
EEPROM on DHSOM
Check whether the ethernet interface is enabled at all before reading
MAC EEPROM. As a cost saving measure, it can happen that the MAC EEPROM
is not populated on SoMs which do not use ethernet.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
The baseboard supports and NVMe drives via the PCIe slot. This
requires a few extra config options to be enabled.
The NVMe can be enumerated with the following commands:
u-boot=> pci enum
PCIE-0: Link up (Gen1-x1, Bus0)
u-boot=> nvme scan
u-boot=> nvme info
Device 0: Vendor: 0x15b7 Rev: 20120022 Prod: 184960441105
Type: Hard Disk
Capacity: 122104.3 MB = 119.2 GB (250069680 x 512)
u-boot=>
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
|
|
The imx8mn-beacon boards can migrate to OF_UPSTREAM which also
allows for the removal the device tree files.
Signed-off-by: Adam Ford <aford173@gmail.com>
|
|
The imx8mm-beacon boards can migrate to OF_UPSTREAM which also
allows for the removal the device tree files.
Signed-off-by: Adam Ford <aford173@gmail.com>
|
|
The imx8mp-beacon boards can migrate to OF_UPSTREAM which also
allows for the removal the device tree files.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
|
|
Since meson G12A, G12B & SM1 based boards switched to using upstream DT,
so drop redundant files from arch/arm/dts directory. Only *-u-boot.dtsi files
kept in arch/arm/dts directory for these boards.
Cc: Sumit Garg <sumit.garg@linaro.org>
Acked-by: Viacheslav Bocharov <adeep@lexina.in>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # khadas-vim3_android
Link: https://lore.kernel.org/r/20240329-u-boot-of-upstream-v2-5-2512ad3eb63d@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
|
|
Enable OF_UPSTREAM to use upstream DT and add amlogic/ prefix to the
DEFAULT_DEVICE_TREE. And thereby directly build DTB from dts/upstream/src/
including *-u-boot.dtsi files from arch/$(ARCH)/dts/ directory.
Cc: Sumit Garg <sumit.garg@linaro.org>
Acked-by: Viacheslav Bocharov <adeep@lexina.in>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # khadas-vim3_android
Link: https://lore.kernel.org/r/20240329-u-boot-of-upstream-v2-4-2512ad3eb63d@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
|
|
Since meson GXL, GXM & AXG based boards switched to using upstream DT,
so drop redundant files from arch/arm/dts directory. Only *-u-boot.dtsi files
kept in arch/arm/dts directory for these boards.
Cc: Sumit Garg <sumit.garg@linaro.org>
Acked-by: Viacheslav Bocharov <adeep@lexina.in>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # khadas-vim3_android
Link: https://lore.kernel.org/r/20240329-u-boot-of-upstream-v2-3-2512ad3eb63d@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
|
|
Enable OF_UPSTREAM to use upstream DT and add amlogic/ prefix to the
DEFAULT_DEVICE_TREE. And thereby directly build DTB from dts/upstream/src/
including *-u-boot.dtsi files from arch/$(ARCH)/dts/ directory.
Cc: Sumit Garg <sumit.garg@linaro.org>
Acked-by: Viacheslav Bocharov <adeep@lexina.in>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # khadas-vim3_android
Link: https://lore.kernel.org/r/20240329-u-boot-of-upstream-v2-2-2512ad3eb63d@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
|
|
is selected
Remove amlogic/ path prefix in CFG_EXTRA_ENV_SETTINGS fdtfile when
using CONFIG_OF_UPSTREAM, otherwise amlogic/ is added twice.
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # khadas-vim3_android
Link: https://lore.kernel.org/r/20240329-u-boot-of-upstream-v2-1-2512ad3eb63d@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
|
|
Improove documentation, add new revision.
Signed-off-by: Viacheslav Bocharov <adeep@lexina.in>
Link: https://lore.kernel.org/r/20240227065551.580199-4-adeep@lexina.in
[narmstrong: squashed https://lore.kernel.org/all/20240326082004.1651782-1-adeep@lexina.in/]
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
|
|
Fix mispell in maintainer name for jethub j100 board files
Signed-off-by: Viacheslav Bocharov <adeep@lexina.in>
Link: https://lore.kernel.org/r/20240227065551.580199-3-adeep@lexina.in
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
|
|
Fix JetHub board sequence to read correct gpio for rescue button
Signed-off-by: Viacheslav Bocharov <adeep@lexina.in>
Link: https://lore.kernel.org/r/20240227065551.580199-2-adeep@lexina.in
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
|
|
Enable support for the DWC3 USB controller and required dependencies for
Qualcomm boards, specifically the DB845c:
* IOMMU / SMMU
* USB high-speed PHYs
* Mass storage and ACM gadgets
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
Qualcomm FDTs are on the larger size, and with the addition of DT
modifications during board_init() it makes sense to enable OF_LIVE
globally. The cost of building the tree should be offset by the
increased efficiency at which we can walk it.
Some rough measurements with CONFIG_BOOTSTAGE suggests that this might
add 0.1-0.2ms to the boot-to-console time. However the reset-to-reset
timer difference is in the range of 0.5ms so this could just be noise.
Suffice to say, no significant slow down.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
The USB VBUS supply for the type-A port is enabled via a GPIO regulator.
This is incorrectly modelled in Linux where only the PCIe dependency is
expressed. The correct way to handle this will be through a
usb-connector node, but for now we'll just mark the regulator as
always-on so that it will be enabled automatically during boot.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
Make sure we power on any boot-on or always-on regulators. These are
used for peripherals like USB on some platforms.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
We don't support the RPM(h)PD power domains in U-Boot, and we don't need
to - the necessary resources are on, and we aren't going to enter any
low power modes.
We could try using a no-op device, but this requires adding a compatible
for every platform, and just pollutes the driver model. So instead let's
just remove every "power-domains" property that references the RPM(h)pd
power controller. This takes <1ms as we're using OF_LIVE.
Of note, this only applies to drivers which are loading post-relocation.
Drivers loaded pre-reloc that reference the rpm(h)pd still need
DM_FLAG_DEFAULT_PD_CTRL_OFF in their flags.
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
We don't support USB super-speed in U-Boot yet, we lack the SS PHY
drivers, however from my testing even with a PHY driver there seem to be
other issues when talking to super-speed peripherals.
In pursuit of maintaining upstream DT compatibility, and simplifying
porting for new devices, let's implement the DT fixups necessary to
configure USB in high-speed only mode at runtime. The pattern is
identical for all Qualcomm boards that use the Synaptics DWC3
controller:
* Add an additional property on the Qualcomm wrapper node
* Remove the super-speed phy phandle and phy-name entries.
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
When using OF_LIVE, the debug UART driver won't be probed if it's a
subnode of the geni-se-qup controller. Add a NOP driver for the
controller to correctly discover its child nodes.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
The .direction_input and .direction_output ops are deprecated, and don't
seem to behave properly for us. Implement our own .set_flags op to
handle this correctly.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
Most devices only initialise the USB clocks for us if we boot via
"fastboot boot", add the missing clock configuration to get both USB
ports working regardless of the bootloader state.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
Define the GDSC power domains for SDM845.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
The RCG registers always have the same offsets, so only store the base
CMD register address and calculate the others relative to that.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
Some devices like the UART and clock controller reference an RPM(h)
power domain. We don't support this device in U-Boot, so add
DM_FLAG_DEFAULT_PD_CTRL_OFF to tell DM core not to try and enable the
power domain.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
Some Qualcomm SoCs newer than SDM845 feature a so-called "7nm phy"
driver, notable the SM8250 SoC which will gain U-Boot support in
upcoming patches.
Introduce a driver based on the Linux driver.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
[code cleanup, align symbol names with Linux, switch to clk/reset_bulk APIs]
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
The Snapdragon 845 and several other Qualcomm SoCs feature this
USB high-speed phy. Add a driver for it based on the Linux driver, with
support for the SDM845, and the QCM2290 and SM6115 SoCs which will gain
support in U-Boot in future patches.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
[code cleanup, switch to clk_bulk]
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
Update Bhupesh's email to his new one.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
This patch is the preparation for SM8150 support. This new SoC
depending on the particular pin can have different numbers for the
same function. For example "rgmii" function for GPIO4 has id=2 while
for GPIO59 it has id=1. So, to support this type of SoCs,
get_function_mux() callback needs to know for which pin the function
is requested.
Signed-off-by: Volodymyr Babchuk <volodymyr_babchuk@epam.com>
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
Now sub-drivers for particular SoCs can register them as power domain
drivers. This is needed for upcoming SM8150 support, because it needs
to power up the Ethernet module.
Signed-off-by: Volodymyr Babchuk <volodymyr_babchuk@epam.com>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
[caleb: make ARCH_SNAPDRAGON select POWER_DOMAIN]
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
The current behaviour does a bitwise OR of the previous and new
divider values, this is wrong as some bits may be set already. We
need to clear all the divider bits before applying new ones.
This fixes potential issue with 1Gbit ethernet on SA8155P-ADP boards.
Signed-off-by: Volodymyr Babchuk <volodymyr_babchuk@epam.com>
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
[caleb: minor wording fix]
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
There are cases when previous bootloader stage leaves some seemingly
valid value in r0, which in fact does not point to valid FDT
blob. This behavior was encountered when trying to boot U-Boot as
"hyp" loader on SA8155P-ADP.
To be sure that we really got the pointer to a device tree we need to
validate it with fdt_check_header() function.
Note: This approach is not 100% fool-proof, as get_prev_bl_fdt_addr()
theoretically can return a pointer to a region that is not physically
mapped and we will get data abort exception when fdt_check_header()
will try to access it. But at this early boot stage we don't know
where RAM is anyways so there is little we can do.
Signed-off-by: Volodymyr Babchuk <volodymyr_babchuk@epam.com>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
QCS404 supports Synopsys Designware Ethernet QOS IP and we already have
the corresponding glue layer present upstream as:
drivers/net/dwc_eth_qos_qcom.c. So enable corresponding support.
Along with that it is possible for Qualcomm platforms to retrieve MAC
address from I2C eeprom present on board. So enable corresponding
support as well.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
Now that Turris Omnia has a rng driver provided in the MCU driver,
enable the rng command in defconfig.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
Add support for true random number generator provided by the MCU on
Turris Omnia. The MCU firmware supports TRNG if the FEAT_TRNG bit is set
in features. In that case we bind the rng driver.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
In the rng command, print
Abort
instead of
Reading RNG failed
if the error number is -EINTR, which can happen if the user pressed
CTRL-C.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
Enable support for the poweroff command via sysreset for Turris Omnia.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
Add support for system power off via UCLASS_SYSRESET. Newer versions of
Turris Omnia MCU firmware can power off the board (MCU will disable
almost all voltage regulators and go into low power mode).
Move the MCU driver into drivers/misc and register it under UCLASS_MISC.
The sysreset and gpio device are bound as child devices of the MCU device.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
Update firmware features reading to try reading 32 bits of features and
fallback to reading 16 bits.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
|
