| Age | Commit message (Collapse) | Author |
|---|
|
This reverts commit 159b6f0e119962ce5da645f548cefe9196c8778e.
Since commit 159b6f0e1199 ("caam: Fix CAAM error on startup") the following
regression was reported by Tim Harvey:
"I've found that this patch causes a regression on an imx8mm board
(imx8mm_venice_defconfig) where the first call to caam_rng_read fails
here in jr_dequeue but if you call it again it works. With some
debugging added:
SEC0: RNG instantiated
...
Hit any key to stop autoboot: 0
u-boot=> rng list
RNG #0 - caam-rng
u-boot=> rng 0 10
caam_rng_read caam-rng len=16
run_descriptor_jr_idx idx=0
Error in SEC deq: -1
caam_rng_read_one run_descriptor_jr failed: -1
caam_rng_read caam-rng caam_rng_read_one failed: -5
Reading RNG failed
u-boot=> rng 0 10
caam_rng_read caam-rng len=16
run_descriptor_jr_idx idx=0
00000000: ad 2e ad c0 2a 12 27 c4 65 82 66 19 be ef f6 07 ....*.'.e.f.....
If I revert your patch caam_rng_read works initially and on subsequent
calls."
" I ran into this when I was testing
lwIP HTTPS as it causes anything that uses dm_rng to fail the first
time (such as HTTPS)."
Revert it for now to avoid the regression.
Reported-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
|
|
Resync all defconfig files using qconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
CONFIG_POSITION_INDEPENDENT to be enabled together"
Yang Xiwen <forbidden405@outlook.com> says:
This patchset also enables CONFIG_POSITION_INDEPENDENT for qemu boards
to avoid similar issues to happen again in the future.
Link: https://lore.kernel.org/r/20250531-pie_blob_fix-v1-0-7b4a37987dbc@outlook.com
|
|
Add 'imply CONFIG_POSITION_INDEPENTDENT' for QEMU arm arch. This allows
qemu arm boards to load u-boot.bin at any address. It is skipped by
default when u-boot is loaded by either --bios or --kernel.
To load u-boot.bin at a different address, one can use u-boot
chain-loading or qemu loader device[1].
[1] https://www.qemu.org/docs/master/system/generic-loader.html
Signed-off-by: Yang Xiwen <forbidden405@outlook.com>
|
|
when CONFIG_BLOBLIST is enabled, the section is switched to .data but is
not switched back to .text. It makes all the code below placed in .data
section, also breaks CONFIG_POSITION_INDEPENDENT.
Fix it by adding `.section .text` to switch the section back to .text.
Fixes: 5103e69344d6 ("arm: armv7: save boot arguments")
Signed-off-by: Yang Xiwen <forbidden405@outlook.com>
|
|
https://source.denx.de/u-boot/custodians/u-boot-rockchip
CI: https://source.denx.de/u-boot/custodians/u-boot-rockchip/-/pipelines/26117
- Allow to silent TPL/SPL debug console;
- enable exFAT support for Theobroma boards;
- Fix SD power initialization in SPL for rk3399-nanopi4
|
|
https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request doc-2025-07-rc4
Documentation:
* fix typo in gcc.rst
* correct EFI_TCG2_PROTOCOL_MEASURE_DTB description
* Add missing reference to firmware for BB-AI64
* Tidy up the bootefi-command docs
|
|
Fix a typo error in gcc.rst, changing "out-out-tree" to
"out-of-tree" in the Out-of-tree section.
Signed-off-by: BehradElmi <behradelmi1@gmail.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
|
|
There are backslashes in some of the tags which seems to be unnecessary.
Remove then.
Change the word 'either' to 'any' since there are three options.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
The details of the sysfw.itb from the R5 build that
also needs to be copied as part of the target images
is missing, but is included in the image formats a
little further down, so add it to the instructions.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
|
|
%s/data that change/data that changes/
%s/cannot be used has/cannot be used for/
%s/Otherwise/Otherwise,/
%s/allows better measurement/allows for better measurement/
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
|
|
The val (the bits to set) is the second member of the reg_data structure
and mask the third one. We obviously want to clear bits 6 and 7 in order
to only set bit 7 in there instead of only clearing bit 7 in order to
write bits 6 and 7 (which makes no sense).
Fortunately, according to the datasheet, bit 6 value doesn't matter when
bit 7 is set so this is essentially just a cosmetic change, no intended
change in behavior.
Fixes: f172575d92cd ("power: rk8xx: add support for RK806")
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
The NanoPi RK3399 boards support UHS-I (up to SDR104) SD cards, however
using any of these 1.8v modes results in a boot failure in SPL upon soft
reboot.
The issue is that the "vcc_sdio" regulator is left at 1.8v on reboot
and the corresponding GPIO defaults to 3.3v. This prevents the SD card
from being reinitialized and read successfully.
This change enables the RK8XX regulators and Rockchip IO-domain drivers
in SPL, which initializes "vcc_sdio" regulator to 3.0v and configures
the GPIO for the correct level on boot.
Signed-off-by: Justin Klaassen <justin@tidylabs.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
This change removes the "regulator-always-on" property from the
"vcc3v0_sd" (vmmc-supply) and "vcc_sdio" (vqmmc-supply) regulators,
which otherwise prevents the MMC driver from being able to power cycle
the SD card as part of the initialization procedure.
It also removes the "regulator-boot-on" from the "vcc_sdio" regulator,
which could theoretically damage a SD card that is already initialized
in a low voltage mode.
Signed-off-by: Justin Klaassen <justin@tidylabs.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Allows use of the regulator functions of the RK8XX PMIC in SPL, which is
necessary to support the functionality of the Rockchip IO-domain driver
on relevant platforms.
Signed-off-by: Justin Klaassen <justin@tidylabs.net>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Allows use of the Rockchip IO-domain driver in SPL to configure
the GPIO to match the voltage supplied by specific regulators
(e.g. "vcc_sdio").
Signed-off-by: Justin Klaassen <justin@tidylabs.net>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Log the value of the regulators during initialization of the IO-domain
driver to aid in debugging GPIO voltage configuration problems.
Signed-off-by: Justin Klaassen <justin@tidylabs.net>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Our upcoming Mass Flasher solution will be storing boot artifacts on an
exFAT partition so enable its support.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Our upcoming Mass Flasher solution will be storing boot artifacts on an
exFAT partition so enable its support.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Our upcoming Mass Flasher solution will be storing boot artifacts on an
exFAT partition so enable its support.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Our upcoming Mass Flasher solution will be storing boot artifacts on an
exFAT partition so enable its support.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Because DEBUG_UART_BOARD_INIT depends on DEBUG_UART, hard dependency
to DEBUG_UART_BOARD_INIT in ROCKCHIP_PX30 can cause warnings if
DEBUG_UART is disabled.
The DEBUG_UART_BOARD_INIT is already implied by ARCH_ROCKCHIP entry.
Remove hard dependency from ROCKCHIP_PX30, so that it will be
consistent with other rockchip boards.
Signed-off-by: Lukasz Czechowski <lukasz.czechowski@thaumatec.com>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Allow to disable serial console in TPL and SPL. Weak dependency
to SPL_SERIAL and TPL_SERIAL is also used in other Rockchip boards.
Signed-off-by: Lukasz Czechowski <lukasz.czechowski@thaumatec.com>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
In case DEBUG UART is not used, define dummy macros replacing
the actual function implementations that will not be available.
This allows to compile code and avoid linker errors.
Redefine the DEBUG_UART_FUNCS macro if DEBUG UART is not available,
to avoid compilation errors.
Signed-off-by: Lukasz Czechowski <lukasz.czechowski@thaumatec.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
The RAM_ROCKCHIP_DEBUG can be used only if DEBUG_UART is
available.
The next commit introduces changes in definition of debug
uart functions, so that DEBUG_UART is required to be defined
in order to initialize uart and use print functions.
Signed-off-by: Lukasz Czechowski <lukasz.czechowski@thaumatec.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
|
|
Update definition of _debug_uart_putc to static inline.
This will allow to avoid compilation warnings about unused code
after introduction of patch changing debug uart functions to
dummies if CONFIG_DEBUG_UART is not set.
This also matches the instructions in include/debug_uart.h and
provides consistency with implementations for other platforms.
Signed-off-by: Lukasz Czechowski <lukasz.czechowski@thaumatec.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Update the definition of _debug_uart_putc to static inline.
This matches the instructions in include/debug_uart.h and
provides consistency with implementations for other platforms.
Signed-off-by: Lukasz Czechowski <lukasz.czechowski@thaumatec.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
https://source.denx.de/u-boot/custodians/u-boot-microblaze
AMD/Xilinx/FPGA changes for v2025.07-rc4
usb:
- Fix regulator handling
net:
- Fix MII clock handling
phy:
- Fix GTR line logic for sgmii
pci:
- Fix pcireg_base logic
fpga:
- Fix change handling in intel_sdm_mb driver
|
|
board_init_f for the am62a is missing the call to spl_enable_cache which
exists for all other am62 platforms (check am625_init.c &
am62p5_init.c).
This allows the usage of caches while loading and parsing the u-boot.img
FIT resulting in ~2x speedup in the A53 SPL stage.
Signed-off-by: Anshul Dalal <anshuld@ti.com>
|
|
There are common MMC args for TI plats in include/environment/ti/mmc.env.
Since we already include this, there is no need to redefine these
MMC vars. Use the defaults.
This seems like something that could have been done while refactoring
these vars in the first place as it happened after this AM62A file
was available hence the fixes tag.
Reported-by: Chirag Shilwant <c-shilwant@ti.com>
Fixes: 3709b529156e ("env: ti: mmc.env: Move mmc related args to common place")
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Acked-by: Chirag Shilwant <c-shilwant@ti.com>
Reviewed-by: Judith Mendez <jm@ti.com>
|
|
This clears UHS_MODE_SELECT for timing modes <= MMC_HS_52.
When initializing to HS400 mode, the host controller downgrades to non-uhs
modes so clear UHS_MODE_SELECT at modes <= MMC_HS_52.
This fixes eMMC writes on j7200 EVM.
Fixes: 6067aa66b3bb ("mmc: am654_sdhci: Add am654_sdhci_set_control_reg")
Signed-off-by: Judith Mendez <jm@ti.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
|
|
The condition here is reversed, which makes link and coral very slow,
leading to lab failures.
Fixes 6c171f7a184 ("common: board: make initcalls static")
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jerome Forissier <jerome.forissier@linaro.org>
|
|
Apart from ENOENT observing return value as ENOSYS when
!DM_REGULATOR that's why cover both configurations.
Changed code is not working as operation should be "&&"
not "||" (ret != -ENOENT && ret != -ENOSYS).
Also fix the remove function where the regulator_set_enable_if_allowed()
function is returning an error.
Signed-off-by: Padmarao Begari <padmarao.begari@amd.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/a2d520f14efc30fc28ec59881205e156dabbfcd9.1744350937.git.michal.simek@amd.com
|
|
https://source.denx.de/u-boot/custodians/u-boot-snapdragon
More Qualcomm fixes for 2025.07
* Adjust fdtfile logic to support more boards
* Support linux,code variable in qcom-pmic button driver
* Minor CLK API adjustments and apq8096/msm8916 fixes
* vbus regulator register fixes
* dragonboard410c KASLR support and other fixes
|
|
Change the vcpumntirq in the GICv3 node from SPI to PPI.
Prevents Linux from complaining:
'[Firmware Bug]: CPU interface incapable of MMIO access'
Fixes: 6d722894fd48 "board: emulation: Add QEMU sbsa support"
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
|
|
Keep spelling.txt in sync with the version from kernel v6.15.
Reported-by: Yao Zi <ziyao@disroot.org>
Reviewed-by: Yao Zi <ziyao@disroot.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
RB1 and RB2 have three root compatibles where the last one can't be used
to decode fdtfile name (qcm* vs qrb*). So rather just rely on the first
compatible to retrieve the SoC name.
Signed-off-by: Sumit Garg <sumit.garg@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250505124333.12344-1-sumit.garg@kernel.org
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>
|
|
Most device vendors put "Volume Down" button onto PMIC RESIN.
But Sony is special: see
dts/upstream/src/arm64/qcom/sdm630-sony-xperia-nile.dtsi or [1].
They put "Volume Down" on PMIC GPIO 7 where others usually put
"Volume Up", and KEY_VOLUMEUP is inside &pon_resin.
Currently if you boot U-Boot on such Sony device, you end up
with 2 "Volume Down" buttons, and no "Volume Up", which makes
navigating menu problematic.
Support reading devicetree "linux,code" property and override
statically defined button code & label based on that.
[1] https://elixir.bootlin.com/linux/v6.15-rc3/source/arch/
arm64/boot/dts/qcom/sdm630-sony-xperia-nile.dtsi#L263
Signed-off-by: Alexey Minnekhanov <alexeymin@postmarketos.org>
Signed-off-by: Alexey Minnekhanov <alexeymin@minlexx.ru>
Reviewed-by: Casey Connolly <casey.connolly@linaro.org>
Link: https://lore.kernel.org/r/20250424014811.3809818-1-alexeymin@minlexx.ru
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>
|
|
As of commit dc8754e8e408 ("clk/qcom: apq8016: improve clk_enable logging")
there are now warnings in the U-Boot console on DragonBoard 410c:
apq8016_clk_enable: unknown clk id 122
apq8016_clk_enable: unknown clk id 123
apq8016_clk_enable: unknown clk id 124
apq8016_clk_enable: unknown clk id 125
This is because we don't implement enable() properly for the SDCC clocks.
Currently they are being enabled as part of set_rate().
Fix this by moving the enable calls out of the apq8016_clk_init_sdc()
function and convert them to the equivalent GATE_CLK_POLLED() definitions.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@oss.qualcomm.com>
Reviewed-by: Casey Connolly <casey.connolly@linaro.org>
Link: https://lore.kernel.org/r/20250424-apq8016-clock-fixes2-v2-6-fcc371c9e45f@linaro.org
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>
|
|
Convert the usages of GATE_CLK() in clock-apq8016 to GATE_CLK_POLLED() to
make sure that we poll the status when enabling clocks:
- PRNG_AHB_CLK is a vote clock, so we poll a different register address.
- The USB clocks are simple branches, so enable/poll is the same register.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@oss.qualcomm.com>
Reviewed-by: Casey Connolly <casey.connolly@linaro.org>
Link: https://lore.kernel.org/r/20250424-apq8016-clock-fixes2-v2-5-fcc371c9e45f@linaro.org
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>
|
|
GATE_CLK() in its current state is unsafe: A simple write to the clock
enable register does not guarantee that the clock is immediately running.
Without polling the clock status, we may issue writes to registers before
the necessary clocks start running. This doesn't seem to cause issues in
U-Boot at the moment, but for example removing the CLK_OFF polling in TF-A
for the SMMU clocks on DB410c reliably triggers an exception during boot.
Make it possible to poll the branch clock status register, by adding a new
GATE_CLK_POLLED() macro that takes the extra register address. Existing
usages work just as before, without polling the clock status. Ideally all
usages should be updated to specify the correct poll address in the future.
The Qualcomm naming for these clocks is "branch" and not "gate", but let's
keep the existing naming for now to avoid confusion until all others
drivers have been converted.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@oss.qualcomm.com>
Reviewed-by: Casey Connolly <casey.connolly@linaro.org>
Link: https://lore.kernel.org/r/20250424-apq8016-clock-fixes2-v2-4-fcc371c9e45f@linaro.org
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>
|
|
The other clock enable functions in clock-qcom.c use setbits_le32() to
read/modify/write the enable registers. Use the same for qcom_gate_clk_en()
to simplify the code a bit.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@oss.qualcomm.com>
Reviewed-by: Casey Connolly <casey.connolly@linaro.org>
Link: https://lore.kernel.org/r/20250424-apq8016-clock-fixes2-v2-3-fcc371c9e45f@linaro.org
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>
|
|
This avoids having to inline it separately into every single clock driver,
when U-Boot is built with support for multiple SoCs.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@oss.qualcomm.com>
Reviewed-by: Casey Connolly <casey.connolly@linaro.org>
Link: https://lore.kernel.org/r/20250424-apq8016-clock-fixes2-v2-2-fcc371c9e45f@linaro.org
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>
|
|
The SDCC_...(n) macros in clock-apq8016.c result in the wrong addresses:
- SDCC1: SDCC_APPS_CBCR(0) = ((0 * 0x1000) + 0x41018) = 0x41018
Should be 0x42018, this is an invalid register close to the USB clocks.
- SDCC2: SDCC_APPS_CBCR(1) = ((1 * 0x1000) + 0x41018) = 0x42018
Should be 0x43018, this is the SDCC1 clock.
When we try to enable SDCC2, we actually end up enabling SDCC1. When we try
to enable SDCC1, we just issue some broken register writes.
This hasn't caused any trouble so far, because the boot firmware is keeping
both SDCC clocks running. However, if these clocks are disabled when
entering U-Boot, MMC initialization is failing.
Fix this by using the proper offset for the macros. The SDCC_CMD_RCGR() was
already correct, but change it the same way for consistency.
Fixes: 085921368b7d ("arm: Add support for Qualcomm Snapdragon family")
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@oss.qualcomm.com>
Reviewed-by: Casey Connolly <casey.connolly@linaro.org>
Link: https://lore.kernel.org/r/20250424-apq8016-clock-fixes2-v2-1-fcc371c9e45f@linaro.org
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>
|
|
Fix and add support for different pmic variants pm8x50b to handle
the vbus regulator.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Link: https://lore.kernel.org/r/20250412174157.104419-1-rui.silva@linaro.org
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>
|
|
When booting Linux, there is currently the following warning in the console
when using the default dragonboard410c_defconfig:
[ 0.000000] KASLR disabled due to lack of seed
Fix this by enabling DM_RNG and RNG_MSM in the defconfig to generate the
KASLR seed:
[ 0.000000] KASLR enabled
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Reviewed-by:
Reviewed-by: Sumit Garg <sumit.garg@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250417-db410c-fixes2-v1-3-76ad994da152@linaro.org
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>
|
|
At the moment, the dragonboard410c_defconfig specifies a custom
SYS_MALLOC_LEN, lower than the default for Qualcomm boards defined in
arch/arm/mach-snapdragon/Kconfig. It looks like it's too low, since
flashing larger sparse partition images using Fastboot fails with:
FAILED (remote: 'Malloc failed for: CHUNK_TYPE_RAW')
We are not really that memory-constrained for U-Boot on DB410c, so fix
this by just dropping the custom malloc size and using the default.
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Reviewed-by:
Reviewed-by: Sumit Garg <sumit.garg@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250417-db410c-fixes2-v1-2-76ad994da152@linaro.org
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>
|
|
Commit 359e1d4a57e0 ("board: dragonboard410c: Use button_cmd instead of
custom code") was made in parallel with commit 8f5685d5d32f ("button:
qcom-pmic: prettify and standardise button labels"), which changed the
default button label from "vol_down" to "Volume Down". This is causing
errors in the console during boot now:
No button labelled 'vol_down'
Fix this by using the new label.
Fixes: 359e1d4a57e0 ("board: dragonboard410c: Use button_cmd instead of custom code")
Fixes: 8f5685d5d32f ("button: qcom-pmic: prettify and standardise button labels")
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Reviewed-by:
Reviewed-by: Sumit Garg <sumit.garg@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250417-db410c-fixes2-v1-1-76ad994da152@linaro.org
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>
|
|
https://source.denx.de/u-boot/custodians/u-boot-i2c
i2c bugfixes for v2025.07-rc4
- designware_i2c: fix globally wrong return value -1 into -ETIMEDOUT
in driver, which leaded in silent errors as a timeout resulted in
an uninitialized value being returned, potentially causing
unexpected behavior.
|
|
CI: https://source.denx.de/u-boot/custodians/u-boot-riscv/-/pipelines/26455
Thanks Conor and Yao for catching this issue.
- Revert "RISC-V 32/64 images support" to fix compatibility issue
|
