| Age | Commit message (Collapse) | Author |
|---|
|
https://source.denx.de/u-boot/custodians/u-boot-stm
STM32 MPU:
- Remove dt-bindings headers available in dts/upstream
- Fixes for stm32prog
- Enable CONFIG_SYS_64BIT_LBA for STM32MP15/13/25 defconfigs
- Add upport of ck_usbo_48m in pre-reloc stage for STM32MP13
- Clean env_get_location() for STM32MP1
- Fix board_get_usable_ram_top() to fix infinite loop in cache
management for STM32MP2.
- Fix ck_flexgen_08 frequency for STM32MP2
STM32 MCU:
- Tune CYCLIC_MAX_CPU_TIME_US to avoid cyclic warning for STM32F469-Disco
- Tune CYCLIC_MAX_CPU_TIME_US to avoid cyclic warning for STM32F769-Disco
|
|
Spurious characters are displayed on U-Boot console.
Usart2 clock is ck_flexgen_08 and its frequency is set
to an incorrect value.
Update ck_flexgen_08 frequency from 100MHz to 64MHz.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
|
mmu_set_region_dcache_behaviour() parameters must be aligned
which is not always the case.
For example for STM32MP2, we stayed stuck inside
mmu_set_region_dcache_behaviour() in an infinite loop because
set_one_region() always return 0 due to start parameter which is
not aligned.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
|
The clock ck_usbo_48m is a clock source for RCC, so the ck_usbo_48m
clock provided by usbphyc need to be probed when RCC clock driver is
required, in pre-reloc stage.
This patch allow to remove the following warning:
clk_register: failed to get ck_usbo_48m device (parent of usbo_k)
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
|
Set multiplier to 'G' if part->size if above SZ_1G.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
|
If CONFIG_SYS_64BIT_LBA flag is enable, following warning is triggered:
../arch/arm/mach-stm32mp/cmd_stm32prog/stm32prog.c: In function 'init_device':
../arch/arm/mach-stm32mp/cmd_stm32prog/stm32prog.c:793:27: warning: format
'%ld' expects argument of type 'long int', but argument 8 has type
'lbaint_t' {aka 'long long unsigned int'} [-Wformat=]
793 | log_debug("MMC %d: lba=%ld blksz=%ld\n", dev->dev_id,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
../include/log.h:157:21: note: in definition of macro 'pr_fmt'
157 | #define pr_fmt(fmt) fmt
| ^~~
../include/log.h:182:33: note: in expansion of macro 'log'
182 | #define log_debug(_fmt...) log(LOG_CATEGORY, LOGL_DEBUG, ##_fmt)
| ^~~
../arch/arm/mach-stm32mp/cmd_stm32prog/stm32prog.c:793:17: note: in expansion
of macro 'log_debug'
793 | log_debug("MMC %d: lba=%ld blksz=%ld\n", dev->dev_id,
| ^~~~~~~~~
../arch/arm/mach-stm32mp/cmd_stm32prog/stm32prog.c:793:42: note: format string
is defined here
793 | log_debug("MMC %d: lba=%ld blksz=%ld\n", dev->dev_id,
| ~~^
| |
| long int
| %lld
Cast block_dev->lba to u64 and set the length specifier to %lld which
is ok with or without CONFIG_SYS_64BIT_LBA flag.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
|
Weijie Gao <weijie.gao@mediatek.com> says:
This patch series add support for MediaTek MT7987 SoC with its reference
boards and related drivers.
This patch series add basic boot support on eMMC/SD/SPI-NOR/SPI-NAND for these
boards. The clock, pinctrl drivers and the SoC initializaton code are also
included.
Link: https://lore.kernel.org/r/cover.1737621362.git.weijie.gao@mediatek.com
|
|
This patch adds general board files based on MT7987 SoC.
MT7987 uses one mmc controller for booting from both SD and eMMC, and the
pins of mmc controller are also shared with one spi controller.
So three configs are need for these boot types:
1. mt7987_rfb_defconfig - SPI-NOR (spi2) and SPI-NAND (spi0)
2. mt7987_emmc_rfb_defconfig - eMMC + SPI-NOR (spi2)
3. mt7987_sd_rfb_defconfig - SD + SPI-NOR (spi2)
Note: spi2 also supports booting from SPI-NAND, but not the default option.
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
|
|
This patch adds basic support for MediaTek MT7987 SoC.
This includes files that will initialize the SoC after boot and
its device tree.
In order to maximize the continuous usable memory space, MT7987 has its
ATF BL31 loaded at the top of RAM. Since u-boot will also locate itself to
top of RAM, u-boot will read the actual memory region of BL31 and set
correct gd->ram_top to avoid u-boot overlapping with BL31.
As now support for mt7987 hasn't been submitted to linux kernel, all dts
filed will be put to arch/arm/dts. They'll be removed after successfully
being merged by linux kernel, and OF_UPSTREAM will also be switched on.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
|
|
Samsung Galaxy Core Prime VE LTE is an entry-level PXA1908-based
smartphone. It has 1GB of DRAM, 8GB eMMC and USB connectivity.
Signed-off-by: Duje Mihanović <duje.mihanovic@skole.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
Add initial support for Marvell PXA1908. The SoC has 4 Cortex-A53 cores,
a GC7000UL GPU and a variety of peripheral controllers.
Signed-off-by: Duje Mihanović <duje.mihanovic@skole.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
Enable bootstd for OpenRD boards
Update defconfigs to the latest u-boot requirements
Remove JFFS2 support. See JFFS2 Vulnerability[1].
Move default envs to text-base environment
[1] https://lore.kernel.org/u-boot/20241114233005.GN3600562@bill-the-cat/T/#m2fc25da1d2c019bc3cd8676991fdd64b8a21aa9b
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-imx
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/24366
- Refactor the imx pinctrl driver.
- Enable optional ENETREF clock on i.MX95
- Remove optional from tee-os entry on the i.MX8M u-boot devicetrees.
|
|
[1] https://git.kernel.org/pub/scm/linux/kernel/git/devicetree/devicetree-rebasing.git
[rockchip fixes from Jonas Karlman via IRC]
|
|
tee-os node is guarded by CONFIG_OPTEE. Since OPTEE adds driver support
for OP-TEE, the binary should then be packaged in the bootable image.
Remove the optional property to enforce this requirement.
Signed-off-by: Yannic Moog <y.moog@phytec.de>
|
|
https://source.denx.de/u-boot/custodians/u-boot-socfpga
1. Bug fixed for doorbell in secure device manager mailbox driver
2. Enhancement on SoCFPGA dwc_eth_xgmac driver
3. Enhancement on DW MAC driver
4. Improved the error message and status for SoC64 device FPGA
configuration driver
5. Updated existing watchdog in system manager to support new SM device
|
|
Currently the FPGA reconfig status only return a single error status
which make the debugging of FPGA reconfiguration hard.
This patch is to expose the error status, major error code and
minor error code, for the FPGA reconfig to upper layer app.
Signed-off-by: Boon Khai Ng <boon.khai.ng@intel.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@intel.com>
|
|
The current write and notify SDM to read mechanism has a flaw where
SDM is not notified enough to be able to read all the data in the buffer.
This is caused by SDM doorbell will only be sent out once the command
buffer overflow check is satisfied. If the command buffer does not reach
overflow status, no SDM doorbell will be sent out, which may cause a
timeout as the mailbox driver will be waiting for the SDM to read the
buffer to empty even though SDM is not notified to do so.
The solution is to remove the command buffer overflow check
and set the SDM doorbell to always trigger at the end of the command
buffer.
This will ensure that the SDM is able to read all of the data.
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
|
|
This commit is to fix the system manager watchdog mode setting to support
until mode_4 for Agilex5. This changes can refer to system manager register
map on wddbg fields.
In Agilex7 it is not detected as an issue because Agilex7 only have 4 watchdog
until mode_3 and it is already been set correctly for it to halt on any CPU in
debug mode. However, in Agilex5 this fix is needed in order to enable the watchdog
pause feature for mode_4 when entering debug mode. If 0xF is not been set on mode_4,
the Watchdog Timers will not halt on any CPU. As by default value, the pause signal
does not assert when any CPU is in debug mode and the watchdog continue to count.
Signed-off-by: Muhammad Hazim Izzat Zamri <muhammad.hazim.izzat.zamri@intel.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@intel.com>
|
|
Michael Chang <zhang971090220@gmail.com> says:
I am resubmitting the patch titled "Add bitbang feature for npcm8xx
and driver" for review and inclusion in the upstream project.
Driver didn't support bitbang feature.
Add bb_miiphy_bus function for driver and open feature for npcm8xx
the log is as below:
-------------------------------------------------
U-Boot 2024.10-g30b9cdaf2df5-dirty (Jan 09 2025 - 00:57:37 +0000)
CPU-0: NPCM845 A1 @ Model: Nuvoton npcm845 Development Board (Device Tree)
DRAM: 1 GiB
RNG: NPCM RNG module bind OK
OTP: NPCM OTP module bind OK
AES: NPCM AES module bind OK
SHA: NPCM SHA module bind OK
I/TC: Reserved shared memory is enabled
I/TC: Dynamic shared memory is enabled
I/TC: Normal World virtualization support is disabled
I/TC: Asynchronous notifications are disabled
Core: 649 devices, 28 uclasses, devicetree: separate
WDT: Not starting watchdog@901c
MMC: sdhci@f0842000: 0
Loading Environment from SPIFlash... SF:
Detected w25q512jvq with page size 256 Bytes, erase size 64 KiB,
total 64 MiB
OK
In: serial@0
Out: serial@0
Err: serial@0
Net: eth0: eth@f0802000, eth1: eth@f0804000, eth3: eth@f0808000
Hit any key to stop autoboot: 0
U-Boot>
U-Boot>
U-Boot>setenv ipaddr 192.168.16.3
U-Boot>ping 192.168.16.12
eth@f0802000 Waiting for PHY auto negotiation to complete
......... TIMEOUT !
Could not initialize PHY eth@f0802000
eth@f0804000 Waiting for PHY auto negotiation to complete
......... TIMEOUT !
Could not initialize PHY eth@f0804000
Speed: 100, full duplex
Using eth@f0808000 device
host 192.168.16.12 is alive
Link: https://lore.kernel.org/r/20250117104540.1580343-1-zhang971090220@gmail.com
|
|
Add bitbang delay through dts properties.
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
Signed-off-by: Michael Chang <zhang971090220@gmail.com>
|
|
Weijie Gao <weijie.gao@mediatek.com> says:
This patch series contains fixes and updates for MediaTek platform,
including drivers, board and arch files.
Link: https://lore.kernel.org/r/cover.1737104723.git.weijie.gao@mediatek.com
|
|
1. Fix mmc clock order of mt7981 to match the clock name
2. Limit the max clock of SD to 50MHz to meet SD Card Spec 2.0
3. Increase the CLK pin driving strength to 8mA
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
|
|
Add driving settings for both SPI and SD/eMMC interfaces to support ensure
flash devices is accessible for ram-booting.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
|
|
This patch add all three GMACs nodes for mt7988. Each GMAC can be
configured to connect to different ethernet switches/PHYs.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
|
|
The CPU port of mt7988 internal switch uses 10Gb link speed.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
|
|
This patch adds PCIe support for mt7988
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
|
|
This patch adds pwm channel 2 (pwm3) support for mt7981
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
|
|
Explicitly add quad mode capabilities or the SPI controller may
start transfer in single mode.
Signed-off-by: SkyLake.Huang <skylake.huang@mediatek.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
|
|
In contrast to some other Allwinner SoCs, there is no difference between
the DTs for the Allwinner A10s/A13 SoCs (sun5i) between the U-Boot and the
Linux kernel repository.
Remove the old copies of the A10s/A13 related .dts and .dtsi files, and
switch most of sun5i boards over to use OF_UPSTREAM.
There are two boards for which we don't have DTs in the kernel tree.
Keep those two .dts files in the legacy U-Boot DT directory, and let
their defconfig opt out of OF_UPSTREAM.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
|
|
In contrast to some other Allwinner SoCs, there is no difference between
the DTs for the Allwinner A10 SoCs (sun4i) between the U-Boot and the
Linux kernel repository.
Remove the old copies of the A10 related .dts and .dtsi files, and switch
most of sun4i boards over to use OF_UPSTREAM.
There are two boards for which we don't have DTs in the kernel tree.
Keep those two .dts files in the legacy U-Boot DT directory, and let
their defconfig opt out of OF_UPSTREAM.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
|
|
In contrast to some other Allwinner SoCs, there is no difference between
the DTs for the Allwinner F1C100/F1C200 SoCs (sunvi) between the U-Boot
and the Linux kernel repository.
Remove the old copies of the F1Cx00 related .dts and .dtsi files, and
switch the whole suniv SoC over to use OF_UPSTREAM.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
|
|
The H616 DRAM controller requires some board specific parameters, which
we declare in Kconfig, let each board specify in their defconfig, and
then use in the DRAM init code.
Other DRAM controllers now require a very similar, if not identical
parameter set, with so far the same parameter names used.
To help keep the Kconfig file at bay, rename the existing parameter
names to drop the H616_ part in there, to make them more naturally
reusable for other SoCs.
No functional change, just a rename.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
|
|
With each new SoC added to the clock_sun50i_h6.h header file, we add a
list of default values for the bus clock registers. This list gets a bit
hard to read, as the spacing between the lines looks confusing.
Tighten the lines by removing empty lines, to make it more obvious which
values belong together. Also remove those comments that were more or
less duplicating the next code line, and didn't add any information.
This makes it easier to find existing values and to add support for new
SoCs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
|
|
commit fc37a73e6679 ("fdt: Swap the signature for
board_fdt_blob_setup()") introduced a subtle change to the Snapdragon
implementation, removing the assignment to gd->fdt_blob partway through
the function.
This breaks qcom_parse_memory() which was also called during
board_fdt_blob_setup().
The underlying issue here is that qcom_parse_memory is using the of_ api
to traverse a devicetree, which relies on the fdt_blob in global data.
Rather than relying on this subtle behaviour, explicitly pass the FDT
that should be consulted for a /memory node.
Using the OF API is typically preferable because it's easier to read,
but using the lower level fdt_ methods instead here doesn't add too much
complexity, I think.
Finally, a minor tweak was made to board_fdt_blob_setup to use the
passed fdt blob pointer instead of gd->fdt_blob, which removes the last
of the references to global data in this area.
Fixes: fc37a73e6679 (fdt: Swap the signature for board_fdt_blob_setup())
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Signed-off-by: Sam Day <me@samcday.com>
Link: https://lore.kernel.org/r/20250122-qcom-parse-memory-updates-v2-1-98dfcac821d7@samcday.com
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
Add initial support for the QCS9100 (derived from SA8775p) Ride platforms.
Define memory layout statically.
Signed-off-by: Varadarajan Narayanan <quic_varada@quicinc.com>
Link: https://lore.kernel.org/r/20250110050817.3819282-3-quic_varada@quicinc.com
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
Weijie Gao <weijie.gao@mediatek.com> says:
This patch series migrates MediaTek MT7629 to OF_UPSTREAM
Changes in v2:
* Remove mt7629-rfb.dtb from arch/arm/dts/Makefile
* Add wdt-reboot node to make reset command work
Link: https://lore.kernel.org/r/cover.1736851116.git.weijie.gao@mediatek.com
|
|
david regan <dregan@broadcom.com> says:
Updates for Broadcom bcmbca devices,
make use of OF_UPSTREAM which uses Linux dts,
update bcmbca dts to current nand node naming convention,
enable basic nand functionality for bcmbca devices.
Link: https://lore.kernel.org/r/20250114045425.148801-1-dregan@broadcom.com
|
|
Add defconfig & devicetree for IBM SBP1 board BMC based on AST2600 SoC.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Naresh Solanki <naresh.solanki@9elements.com>
|
|
Move differences in DT files between upstream Linux DT and U-Boot DT to
mt7629-rfb-u-boot.dtsi.
Remove old copies of mt7629-related clock bindings, .dts, and .dtsi files.
Update defconfig to switch the whole mt7629 SoC to use OF_UPSTREAM.
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
|
|
Update bcmbca dts to current nand node naming convention.
Changes in v2:
- Removed addition of nand-on-flash-bbt parameter
Signed-off-by: david regan <dregan@broadcom.com>
Reviewed-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Anand Gore <anand.gore@broadcom.com>
|
|
Make use of OF_UPSTREAM which uses Linux dts.
Changes in v2:
- Removed enabling of nand functionality
Signed-off-by: david degan <dregan@broadcom.com>
Reviewed-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Anand Gore <anand.gore@broadcom.com>
|
|
Now that block drivers are all selecting the BLK symbol, there's no need
for other options to be select'ing BLK so that other required
functionality can be enabled. Remove these places.
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
At this point in time, DM is always enabled. So if MMC is enabled, it
should select DM_MMC. No drivers need to depend on DM_MMC being enabled
now, so remove that from dependency lists. This now means that a number
of platforms which select'd DM_MMC need to select MMC instead. This also
fixes a migration problem with espresso7420 in that MMC is built again
with the platform.
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-imx
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/24263
- Add i.MX95 EMDIO support
- Guard binman nodes with CONFIG_OPTEE on imx8m
- Enable CAAM in phycore-imx8mp SPL.
- Fix Fix NULL dereference in imx_pinctrl_probe().
|
|
Delete tifs DT node as part of fixup.
TISCI API reported msmc_size, does not include 64KB reserved size for
tifs aka MSMC comms memory, see documentation[0].
As part of fixup, original code uses TISCI API reported msmc_size as
size for SRAM DT node.
tifs node is similar to l3-cache, which should hold address above
msmc_size, and should be deleted before passing control to OS.
[0] https://software-dl.ti.com/tisci/esd/latest/2_tisci_msgs/general/core.html?highlight=msmc#tisci-msg-query-msmc
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
|
|
The default value for the mux to select the parent clock,
AUDIO_REFCLK1_CTRL_CLK_SEL is '11111' (31) but the mux input for 31
is marked as 'Reserved' so the ti-sci-clk call for get-parent fails.
Mark it to a valid value, '11100' (28) for MAIN_PLL4_HSDIV2_CLKOUT
to get rid of the linux failures during boot-time like:
"[ 1.573193] ti-sci-clk 44083000.system-controller:clock-controller:
get-parent failed for dev=157, clk=34, ret=-19"
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
|
|
Guard binman nodes with CONFIG_OPTEE to fix the following error
when building without optee support:
BINMAN .binman_stamp
Image 'image' has faked external blobs and is non-functional: tee.bin
Image 'image' is missing optional external blobs but is still functional: tee-os
/binman/section/fit/images/tee/tee-os (tee.bin):
See the documentation for your board. You may need to build Open Portable
Trusted Execution Environment (OP-TEE) and build with TEE=/path/to/tee.bin
Some images are invalid
make: *** [Makefile:1135: .binman_stamp] Error 103
While at it, only pass tee to the loadables lines when CONFIG_OPTEE is
defined.
Reported-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Yannic Moog <y.moog@phytec.de>
|
|
https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request efi-2025-04-rc1
Documentation:
* Correct the defconfig name in the coolpi documentation
UEFI:
* Carve out the biggest part of the RISC-V and ARM linker scripts for EFI
binary into a common include.
* Correct the values of SizeOfCode and SizeOfInitializedData in generated
EFI binaries for RISC-V and ARM.
* Avoid gaps between sections in EFI binaries causing a failure in secure
boot.
* Makefile: let clean remove capsule_in.capsule*.efi-capsule
* Refactor some of the code used for launching EFI binaries.
|
|
Most R-Car Gen3 and Gen4 systems require extalr_clk very early
in the boot process. Currently the extalr_clk { bootph-all } DT
property to indicate this clock should be available early is set
in each SoC U-Boot DT extras file. Deduplicate this assignment to
new common r8a779x-rcar64-u-boot.dtsi file.
Note that R-Car Gen3 R8A77990 E3 and R8A77995 D3 and RZ R8A774C0
do not require extalr_clk early, therefore these SoCs still include
plain r8a779x-u-boot.dtsi in their U-Boot DT extras .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
