| Age | Commit message (Collapse) | Author |
|---|
|
As indicated in kernel led dt-bindings, label is a deprecated
property, so remove it and use led node's name instead for
u-boot,error-led property.
Rename red led node's name to led-red.
Remove status property which is useless.
Add compatible = "gpio-leds" which is not present in kernel DT.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
|
red led and button dedicated to fastboot share the same gpio GPIOA13.
Led driver is probed early so the corresponding gpio is taken and
configured in output which forbid fastboot and stm32prog button usage.
To avoid this, remove the "default-state" property from red led node.
This will avoid to trigger the led driver probe() to configure the led
default state during startup.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
|
Add 2 gpio-keys :
_ button-user-1 for stm32prog mode activation.
_ button-user-2 for fastboot mode activation.
Remove proprietary st,fastboot-gpios and st,stm32prog-gpios.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
|
As indicated in kernel led dt-bindings, label is a deprecated
property, so remove it and use blue led node's name instead
for u-boot,boot-led property.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
|
As indicated in kernel led dt-bindings, label is a deprecated
property, so remove it and use red led node's name instead
for u-boot,error-led property.
Rename red led node's name to led-red.
Remove status property which is useless.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
|
red led and button dedicated to fastboot share the same gpio GPIOA13.
Led driver is probed early so the corresponding gpio is taken and
configured in output which forbid fastboot and stm32prog button usage.
To avoid this, remove the "default-state" property from red led node.
This will avoid to trigger the led driver probe() to configure the led
default state during startup.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
|
Instead of using "st,fastboot-gpios" and "st,stm32prog-gpios", declare
2 gpio-keys.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
|
As indicated in kernel led dt-bindings, label is a deprecated
property, so remove it and use blue led node's name instead
for u-boot,boot-led property.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
|
As indicated in kernel led dt-bindings, label is a deprecated
property, so remove it and use red led node's name instead
for u-boot,error-led property.
Rename "red" led node's name to "led-red".
Remove status property which is useless.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
|
red led and button dedicated to fastboot share the same gpio GPIOA13.
Led driver is probed early so the corresponding gpio is taken and
configured in output which forbid fastboot and stm32prog button usage.
To avoid this, remove the "default-state" property from red led node.
This will avoid to trigger the led driver probe() to configure the led
default state during startup.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
|
Instead of using "st,fastboot-gpios" and "st,stm32prog-gpios", declare
2 gpio-keys.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
|
Remove "color" property from led-red node which is not supported
by U-Boot.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
|
led-red and button dedicated to fastboot share the same gpio GPIOA13.
led-blue and button dedicated to stm32prog share the same gpio GPIOA14.
Led driver is probed early so the corresponding gpio is taken and
configured in output which forbid fastboot and stm32prog button usage.
To avoid this, remove the "default-state" property from led-red and
led-blue led's node.
This will avoid to trigger the led driver probe() to configure the led
default state during startup.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
|
Add 2 gpio-keys :
_ button-user-1 for stm32prog mode activation.
_ update button-user's label (defined in kernel DT) to match label
requested in board_key_check() for fastboot mode activation.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
|
Fix flash@0 partition node name with correct offset.
Fixes: 90f992e6a58c ("arm: dts: stm32: Add partitions in flash0 and nand
node for stm32mp15xx-dhcom/dhcor")
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
|
Fix flash@0 partition node name with correct offset.
Fixes: 90f992e6a58c ("arm: dts: stm32: Add partitions in flash0 and nand node for
stm32mp15xx-dhcom/dhcor")
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
|
Fix flash@0 and nand@0 partition node name with correct offset.
Fixes: e91d3c61767b ("arm: dts: stm32: Add partitions in flash0 and nand
node for stm32mp15xx-ev1")
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
|
In case of an OTP-CLOSED STM32MP15xx system, the CPU core 1 cannot be
released from endless loop in BootROM only by populating TAMP BKPxR 4
and 5 with magic and branch address and sending SGI0 interrupt from
core 0 to core 1 twice. TAMP_SMCR BKP..PROT fields must be initialized
as well to release the core 1 from endless loop during the second SGI0
handling on core 1. Initialize TAMP_SMCR to protect the first 32 backup
registers, the ones which contain the core 1 magic, branch address and
boot information.
This requirement seems to be undocumented, therefore it was necessary
to trace and analyze the STM32MP15xx BootROM using OpenOCD and objdump.
Ultimately, it turns out that a certain BootROM function reads out the
TAMP_SMCR register and tests whether the BKP..PROT fields are non-zero.
If they are zero, the BootROM code again waits for SGI0 using WFI, else
the execution moves forward until it reaches handoff to the TAMP BKPxR 5
branch address.
This fixes CPU core 1 release using U-Boot PSCI implementation on an
OTP-CLOSED system, i.e. system with fuse 0 bit 6 set.
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
SoC revision is only accessible via DBUMCU IDC register,
which requires BSEC.DENABLE DBGSWENABLE bit to be set to
make the register accessible, otherwise an access to the
register triggers bus fault. As BSEC.DBGSWENABLE is zero
in case of an OTP-CLOSED system, do NOT set DBGSWENABLE
bit as this might open a brief window for timing attacks.
Instead, report that this system is OTP-CLOSED and do not
report any SoC revision to avoid confusing users. Use an
SEC/C abbreviation to avoid growing SOC_NAME_SIZE .
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
The source file is in arch/arm/mach-stm32mp/ecdsa_romapi.c and not
in arch/arm/mach-stm32mp/stm32mp1/ecdsa_romapi.c . There are two
Makefile entries in each subdirectory. Drop the bogus one and keep
only the correct one, the one in arch/arm/mach-stm32mp/Makefile .
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
In case the system has resumed successfully, the PSCI suspend resume
code has to jump to the 'ep' successful resume entry point code path,
otherwise the code has to jump to content of the LR register, which
points to failed resume code path.
To implement this distinction, rewrite LR register stored on stack
with 'ep' value in case of a successful resume, which is really in
every case unless some catastrophic failure occurred during suspend.
Without this change, Linux counts every resume as failed in
/sys/power/suspend_stats/fail
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
This patch avoids compilation issue when CONFIG_USB_GADGET is deactivated
in defconfig, with undefined reference to run_usb_dnl_gadget and to
g_dnl_set_product.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
https://source.denx.de/u-boot/custodians/u-boot-mpc8xx
This pull request adds support for temperature sensors et FPGA loading
on boards from CS GROUP France.
CI: https://source.denx.de/u-boot/custodians/u-boot-mpc8xx/-/pipelines/20416
|
|
enabled""
As reported by Jonas Karlman this series breaks booting on some AArch64
platforms with common use cases. For now the best path forward is to
revert the series.
This reverts commit 777c28460947371ada40868dc994dfe8537d7115, reversing
changes made to ab3453e7b12daef47b9e91da2a2a3d48615dc6fc.
Link: https://lore.kernel.org/u-boot/50dfa3d6-a1ca-4492-a3fc-8d8c56b40b43@kwiboo.se/
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
|
|
Unlike CMPC885 and CMPCPRO boards, the FPGA of MCR3000 board doesn't
load code automatically but needs to be loaded by software through SPI.
Until now it was loaded later by Linux, but we'd like U-boot to have
access to some information that require the FPGA, like board address
in racks.
So, implemented the load of FPGA in U-boot.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
---
To avoid spamming your email boxes, the code isn't included in
the emailed patch but will be present in the PULL request
|
|
SDMA configuration register needs to be set up only once and doesn't
belong to drivers. Also, the value to be used is different on mpc885.
So do the init in cpu_init_f() with 0x40 for mpc885 and 0x1 for others.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
|
|
All CSSI boards have an LM74 chip as temperature sensor.
Enable it.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
|
|
MCR3000 board has some components tied to the SPI bus, like the Texas
Instruments LM74 temperature sensor.
Add support for SPI bus. The SPI chipselects are a bit special in the
way that they are driven by 3 bits in a register of the board's CPLD
where the value writen in those bits exclusively activates one of the
7 possible chipselects and value 0 sets all chipselets to inactive.
So add a special GPIO driver that simulates GPIOs for those chipselect.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
|
|
When adding additional SPI peripherals, the reg property needs to
be added, and this leads to the following error:
arch/powerpc/dts/cmpc885.dtb: Warning (reg_format): /immr@ff000000/spi@aa0/temp@1:reg: property has invalid length (4 bytes) (#address-cells == 1, #size-cells == 1)
arch/powerpc/dts/cmpc885.dtb: Warning (reg_format): /immr@ff000000/spi@aa0/temp@2:reg: property has invalid length (4 bytes) (#address-cells == 1, #size-cells == 1)
Fix it by removing cell-index and cell-size which is unused and add
reg property. Also fix node name to be in line with reg value.
Also add missing compatible for eeprom node.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
|
|
Enable OF_UPSTREAM to use upstream DT and add renesas/ prefix to the
DEFAULT_DEVICE_TREE and OF_LIST. And thereby directly build DTB from
dts/upstream/src/ including *-u-boot.dtsi files from arch/$(ARCH)/dts/
directory.
The configuration update has been done using the following script:
```
sed -i '/^CONFIG_DEFAULT_DEVICE_TREE/ s@="@&renesas/@' `git grep -li renesas configs`
sed -i '/^CONFIG_OF_LIST/ s@r8a@renesas/&@g' `git grep -li renesas configs`
```
The RZN1 Snarc board does not seem to have a matching Linux kernel
DT counterpart, this is currently not switched to OF upstream.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
|
|
Enable OF_UPSTREAM to use upstream DT and add renesas/ prefix to the
DEFAULT_DEVICE_TREE and OF_LIST. And thereby directly build DTB from
dts/upstream/src/ including *-u-boot.dtsi files from arch/$(ARCH)/dts/
directory.
The configuration update has been done using the following script:
```
sed -i '/^CONFIG_DEFAULT_DEVICE_TREE/ s@="@&renesas/@' `git grep -li renesas configs`
sed -i '/^CONFIG_OF_LIST/ s@r8a@renesas/&@g' `git grep -li renesas configs`
```
There are SoCs which are not included in this patch. The 32bit SoCs
require further infrastructure work. R8A779H0 is coming during the
next upstream DT synchronization cycle as it is not included in
current upstream DTs yet.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Adam Ford <aford173@gmail.com> # Beacon boards
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
|
|
R-Car R8A77950 H3 ES1.* was only available to an internal development
group and needed a lot of quirks and workarounds. Public users only
have R-Car R8A77950 H3 ES2 and newer. Switch existing systems to use
R8A77951 device trees.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
|
The U-Boot build system can automatically paste -u-boot.dtsi at the
end of matching .dts during build. Stop emulating this behavior and
rename the -u-boot.dts files to -u-boot.dtsi, drop "#include...dts"
from those new u-boot.dtsi files, and update board configuration
accordingly.
The rename, '#include...dts` scrubbing and configuration update has
been done using the following script:
```
$ find . -name r[78]\*-u-boot.dts | sort -u | while read line ; do \
git mv ${line%-u-boot.dts}-u-boot.dts ${line%-u-boot.dts}-u-boot.dtsi ; \
done
$ sed -i '/^#include.*dts"/ d' `find . -name r[78]\*-u-boot.dtsi`
$ sed -i 's@-u-boot@@g' `git grep -li renesas configs`
```
The Salvator-X and ULCB board files have been updated manually.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Adam Ford <aford173@gmail.com>
|
|
If open() fails it returns -1. Calling close() with this value
makes no sense. Return -EIO instead.
Addresses-Coverity-ID: 185828 Improper use of negative value
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Fixes: 566bf3a8698 ("sandbox: Add a function to read a host file")
Reviewed-by: Sean Anderson <seanga2@gmail.com>
|
|
When we find a certificate on an image to be booted on a GP device we
print out a message explaining that the certificate is being skipped.
This message is rather long and is printed for every image. Shorten
the message and make the long version into a debug message.
Signed-off-by: Andrew Davis <afd@ti.com>
Tested-by: Jonathan Humphreys <j-humphreys@ti.com>
|
|
Add Kconfig that enables FPGA reprogramming with warm boot on Arria 10.
This option allows to change the bitstream on the filesystem and apply
changes with warm reboot without the need for a power cycle.
Signed-off-by: Michał Barnaś <barnas@google.com>
|
|
MD Danish Anwar <danishanwar@ti.com> says:
Introduce ICSSG PRUETH support in uboot. The ICSSG driver is used in TI
AM654 SR2.0.
The ICSSG PRU Sub-system runs on EMAC firmware. This series Introduces
support for ICSSG driver in uboot.
This series has been tested on AM65x SR2.0, and the ICSSG interface is
able to ping / dhcp and boot kernel using tftp in uboot.
To use ICSSG2 ethernet, the ICSSG firmware needs to be loaded to PRU RPROC
cores and RPROC cores need to be booted with the firmware. This step is
done inside driver similar to kernel.
The remoteproc driver uses request_fw_into_buf() API from fs-loader driver
to load and start rproc with the required firmwares.
This series only introduces driver files. The device tree and config
changes to enable ICSSG driver will be introduced later.
|
|
This is the PRUSS Ethernet driver for TI AM654 SR2.0 and later SoCs with
the ICSSG PRU Sub-system running EMAC firmware. ICSSG Subsystem supports
two slices per instance. This driver caters to both slices / ports of
the icssg subsystem.
Since it is not possible for Ethernet driver to register more than one
port for a given instance, this patch introduces top level PRUETH as
UCLASS_MISC and binds UCLASS_ETH to individual ports in order to support
bringing up more than one Ethernet interface in U-Boot.
Since top level driver is UCLASS_MISC, board files would need to
instantiate the driver explicitly.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
|
|
The function uniphier_mem_map_init() is to change global variable
'mem_map', which is referenced to get_page_table_size() to calculate
the size of page table.
However, uniphier_mem_map_init() is called after get_page_table_size(),
so the size of page table and 'mem_map' become inconsist each other.
After all, U-Boot fails to boot on chip with memory map different from
default map,
uniphier_mem_map_init() should be moved to dram_init(), which is
called before get_page_table_size().
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
|
|
Mentions that command line option --signal is needed to make use of this
configuration option.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
|
|
Instead of checking a configuration setting in booti_start() adjust the
sandbox implementation of booti_setup().
Write a console message when trying to run the booti command on the sandbox
indicating that it is not supported.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
|
|
We should check the return value of fcntl().
Addresses-Coverity-ID: 131108 ("Unchecked return value from library")
Addresses-Coverity-ID: 131109 ("Unchecked return value from library")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
|
|
Introduce get_boot_device() to obtain the booting device. Make it also
available for non SPL builds so u-boot can also know the device it is
booting from.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
|
|
Relocate booindex to OCRAM region after it gets opened by TIFS so
the main domain bootloaders can have access to this data.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
|
|
Add support for signing of TIFSSTUB images for HSSE, HSFS and GP devices
and include them in tispl.bin and tispl.bin_unsigned.
Signed-off-by: Kamlesh Gurudasani <kamlesh@ti.com>
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
|
|
Add support for detecting and processing TIFSSTUB images for HS, HSFS
and GP devices.
TIFSSTUB image for related device type will be loaded, rest TIFSSTUB
images will be discarded.
Example, for GP device, tifsstub-gp will be loaded, tifsstub-hs and
tifsstub-fs will be discarded.
Signed-off-by: Kamlesh Gurudasani <kamlesh@ti.com>
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
|
|
Move verdin-am62 to OF_UPSTREAM:
- handle the fact that dtbs now have a 'ti/' prefix
- imply OF_UPSTREAM
- remove redundant files from arch/arm/dts leaving only the
*-u-boot.dtsi files
- update MAINTAINERS file
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
|
|
This extra binding is non-standard and now unneeded as we bind the
sysreset driver automatically. This matches what is done in Linux
and allows us to more closely match the DTBs. Remove the binding
and all users.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Tested-by: Jonathan Humphreys <j-humphreys@ti.com>
|
|
During the boot, the EFI loader maps the memory from ram_top to ram_end
as EFI_BOOT_SERVICES_DATA. When LMB does boot_fdt_add_mem_rsv_regions()
to OPTEE, TFA, R5, and M4F DMA/memory "no-map" for the kernel it produces
the following error message:
ERROR: reserving fdt memory region failed (addr=9cb00000 size=100000 flags=4)
ERROR: reserving fdt memory region failed (addr=9cc00000 size=e00000 flags=4)
ERROR: reserving fdt memory region failed (addr=9da00000 size=100000 flags=4)
ERROR: reserving fdt memory region failed (addr=9db00000 size=c00000 flags=4)
ERROR: reserving fdt memory region failed (addr=9e780000 size=80000 flags=4)
ERROR: reserving fdt memory region failed (addr=9e800000 size=1800000 flags=4)
To avoid this, don't flag with EFI_BOOT_SERVICES_DATA the memory from
ram_top to ram_end by the EFI loader.
Signed-off-by: Vitor Soares <vitor.soares@toradex.com>
|
