| Age | Commit message (Collapse) | Author |
|---|
|
TAMP backup registers will be exposed as nvmem cells.
Each registers ([0..127] for STM32MP2, [0..31] for STM32MP1) could be
exposed as nvmem cells under the nvram node in device tree
Signed-off-by: Simeon Marijon <simeon.marijon@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
|
The ROM API table location is passed to the SPL by BootROM in register r0,
make use of this, store the content of r0 and later use it to access the
ROM API table to determine current boot device.
Signed-off-by: Marek Vasut <marek.vasut@mailbox.org>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
The DBGMCU block is available at address 0x50081000 both on STM32MP13xx
and on STM32MP15xx . There is no reason to limit the DBGMCU macro being
set only on STM32MP15xx , remove the ifdeffery.
Signed-off-by: Marek Vasut <marek.vasut@mailbox.org>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
The STM32MP13xx has only 128 kiB of SYSRAM starting at address 0x2ffe0000 .
The STM32MP15xx has 256 kiB of SYSRAM starting at address 0x2ffc0000 . Make
sure both SoCs configure ARMV7_SECURE_BASE correctly . Define the SYSRAM
base in stm32.h to be consistent with the STM32MP15xx macro.
Signed-off-by: Marek Vasut <marek.vasut@mailbox.org>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
Drop a space after tab, no functional change.
Signed-off-by: Marek Vasut <marek.vasut@mailbox.org>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
SCMI clocks are now available, switch from fixed to SCMI clocks.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
|
Prepare v2025.07-rc4
|
|
CONFIG_POSITION_INDEPENDENT to be enabled together"
Yang Xiwen <forbidden405@outlook.com> says:
This patchset also enables CONFIG_POSITION_INDEPENDENT for qemu boards
to avoid similar issues to happen again in the future.
Link: https://lore.kernel.org/r/20250531-pie_blob_fix-v1-0-7b4a37987dbc@outlook.com
|
|
Add 'imply CONFIG_POSITION_INDEPENTDENT' for QEMU arm arch. This allows
qemu arm boards to load u-boot.bin at any address. It is skipped by
default when u-boot is loaded by either --bios or --kernel.
To load u-boot.bin at a different address, one can use u-boot
chain-loading or qemu loader device[1].
[1] https://www.qemu.org/docs/master/system/generic-loader.html
Signed-off-by: Yang Xiwen <forbidden405@outlook.com>
|
|
when CONFIG_BLOBLIST is enabled, the section is switched to .data but is
not switched back to .text. It makes all the code below placed in .data
section, also breaks CONFIG_POSITION_INDEPENDENT.
Fix it by adding `.section .text` to switch the section back to .text.
Fixes: 5103e69344d6 ("arm: armv7: save boot arguments")
Signed-off-by: Yang Xiwen <forbidden405@outlook.com>
|
|
Add an OpenSBI entry to the FIT image. As it expects an FDT to be
passed, corresponding FDT entry is generated with of-list as well.
As SPL now passes a full FDT for following stages, proper U-Boot image
is packed into u-boot-with-spl.bin without a devicetree copy included.
Signed-off-by: Yao Zi <ziyao@disroot.org>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
|
|
These operations rely on a customized M-mode CSR, MHCR, which isn't
available when running in S mode.
Let's fallback to the generic weak stub when running in S mode to avoid
illegal accesses.
Signed-off-by: Yao Zi <ziyao@disroot.org>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
|
|
Symbols in spl.c only function correctly in SPL stage. Build the file
for SPL only to avoid weak symbols in proper U-Boot being unexpectedly
reloaded.
Fixes: 5fe9ced3552 ("riscv: cpu: Add TH1520 CPU support")
Signed-off-by: Yao Zi <ziyao@disroot.org>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
|
|
Tom Rini <trini@konsulko.com> says:
Taking inspiration from Heiko's patch[1] this series goes and cleans up
all of the arch/arm/dts/*.h files that can be easily removed. The big
challenge I ran in to here was that for some platforms that aren't using
OF_UPSTREAM were didn't have a sufficiently deep search path to find
files there rather than arch/arm/dts. This also showed that only ARM had
local header files to deal with.
[1]: https://lore.kernel.org/u-boot/20250528090536.765499-1-heiko.thiery@gmail.com/
Link: https://lore.kernel.org/r/20250528233050.3820722-1-trini@konsulko.com
|
|
We have this file in both arch/arm/dts and
dts/upstream/src/arm64/freescale. This file is identical save for
changes which have been made upstream. Remove our local copy to get in
sync with upstream now.
Acked-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
We have these files in both arch/arm/dts and
dts/upstream/src/arm/microchip. These files are identical save for
changes which have been made upstream. Remove our local copy to get in
sync with upstream now.
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
As part of moving to using OF_UPSTREAM and so the upstream DT related
header files we have a header that is under the arch/arm/dts directory
and differ in being a strict subset of what is found upstream. We can
remove this now to prevent future conflicts.
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
As part of moving to using OF_UPSTREAM and so the upstream DT related
header files we have a number of these headers that are under the
arch/arm/dts directory and differ only in combinations of spacing
changes and/or switching to SPDX license tags. We can remove these now
to prevent future conflicts.
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
As part of moving to using OF_UPSTREAM and so the upstream DT related
header files we have a number of these headers that are under the
arch/arm/dts directory and are currently identical to the versions in
dts/upstream. We can remove these now to prevent future conflicts.
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
As part of moving to using OF_UPSTREAM and so the upstream DT related
header files we have a header that is under the arch/arm/dts directory
and now unused. We can remove this now to prevent any future conflicts.
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
The NanoPi RK3399 boards support UHS-I (up to SDR104) SD cards, however
using any of these 1.8v modes results in a boot failure in SPL upon soft
reboot.
The issue is that the "vcc_sdio" regulator is left at 1.8v on reboot
and the corresponding GPIO defaults to 3.3v. This prevents the SD card
from being reinitialized and read successfully.
This change enables the RK8XX regulators and Rockchip IO-domain drivers
in SPL, which initializes "vcc_sdio" regulator to 3.0v and configures
the GPIO for the correct level on boot.
Signed-off-by: Justin Klaassen <justin@tidylabs.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
This change removes the "regulator-always-on" property from the
"vcc3v0_sd" (vmmc-supply) and "vcc_sdio" (vqmmc-supply) regulators,
which otherwise prevents the MMC driver from being able to power cycle
the SD card as part of the initialization procedure.
It also removes the "regulator-boot-on" from the "vcc_sdio" regulator,
which could theoretically damage a SD card that is already initialized
in a low voltage mode.
Signed-off-by: Justin Klaassen <justin@tidylabs.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Because DEBUG_UART_BOARD_INIT depends on DEBUG_UART, hard dependency
to DEBUG_UART_BOARD_INIT in ROCKCHIP_PX30 can cause warnings if
DEBUG_UART is disabled.
The DEBUG_UART_BOARD_INIT is already implied by ARCH_ROCKCHIP entry.
Remove hard dependency from ROCKCHIP_PX30, so that it will be
consistent with other rockchip boards.
Signed-off-by: Lukasz Czechowski <lukasz.czechowski@thaumatec.com>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Allow to disable serial console in TPL and SPL. Weak dependency
to SPL_SERIAL and TPL_SERIAL is also used in other Rockchip boards.
Signed-off-by: Lukasz Czechowski <lukasz.czechowski@thaumatec.com>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Update the definition of _debug_uart_putc to static inline.
This matches the instructions in include/debug_uart.h and
provides consistency with implementations for other platforms.
Signed-off-by: Lukasz Czechowski <lukasz.czechowski@thaumatec.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
This file is a duplicate and also comes with the sync of the linux
mainline dts files. By removing this the one from the dts folder should
be taken that is more up-to-date.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
|
|
Clang is stricter than GCC when it comes to inline assembly and expects the
register to be written with explicitly same type of variable.
Fixes: c0e1775a867c ("armv8: Add arch-specific sysinfo platform driver")
Signed-off-by: Raymond Mao <raymond.mao@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
|
|
board_init_f for the am62a is missing the call to spl_enable_cache which
exists for all other am62 platforms (check am625_init.c &
am62p5_init.c).
This allows the usage of caches while loading and parsing the u-boot.img
FIT resulting in ~2x speedup in the A53 SPL stage.
Signed-off-by: Anshul Dalal <anshuld@ti.com>
|
|
The kernel added new size definitions and substituted the
boilerplate/reference to the license with a SPDX identifier.
Drop a local SZ_8G definition in MediaTek MT7988 SoC board file.
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Weijie Gao <weijie.gao@mediatek.com>
|
|
This adds initial support for the Toradex Verdin AM62P module.
The module consists of an TI AM62P family SoC, a TPS65219 PMIC, a
Gigabit Ethernet PHY, up to 8GB of LPDDR4 RAM, an eMMC, a TLA2024 ADC,
an I2C EEPROM, an RX8130 RTC, plus an optional Bluetooth/Wi-Fi module.
These specific changes adds support for Toradex Verdin AM62P Quad 2GB WB
IT module.
Link: https://www.toradex.com/computer-on-modules/verdin-arm-family/ti-am62p
Link: https://www.toradex.com/products/carrier-board/verdin-development-board-kit
Signed-off-by: Parth Pancholi <parth.pancholi@toradex.com>
Signed-off-by: Vitor Soares <vitor.soares@toradex.com>
|
|
https://source.denx.de/u-boot/custodians/u-boot-snapdragon
More Qualcomm fixes for 2025.07
* Adjust fdtfile logic to support more boards
* Support linux,code variable in qcom-pmic button driver
* Minor CLK API adjustments and apq8096/msm8916 fixes
* vbus regulator register fixes
* dragonboard410c KASLR support and other fixes
|
|
Tom Rini <trini@konsulko.com> says:
Hey all,
Related to my other series I've posted recently on cleaning up some
headers, this series here is the result of at least lightly auditing the
#includes used in include/[a-m]*.h. This ignores subdirectories, as at
least in part I think the top-level includes we've constructed are the
most likely places to have some extra transitive include paths. I'm sure
there's exceptions and I'll likely audit deeper once this first pass is
done. This only gets as far as "include/m*.h" because I didn't want this
to get too big. This also sets aside <miiphy.h> and <phy.h>. While
miiphy.h does not directly need <phy.h> there are *so* many users and I
think I had half of the tree just about not building when I first tried.
It might be worth further investigation, but it might just be OK as-is.
Link: https://lore.kernel.org/r/20250521230119.2084088-1-trini@konsulko.com
|
|
The value of "ETH_ALEN" is defined to 6 in <linux/if_ether.h>. This file
is included in <net.h>. In the places where we had ETH_ALEN but no
direct include of <net.h>, add <linux/if_ether.h>. In the places where
we had a custom name used, make use of ETH_ALEN instead.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
There are only a few things found in <mtd.h> today. Go through and audit
the C files which include <mtd.h> and remove it when not required. Then,
add it to the files which had either missed it or had an indirect
inclusion of it.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This file does not need <linux/sizes.h> nor <linux/compiler.h> so remove
them. This exposes however that a number of other files had been relying
on this implicit include for <linux/sizes.h> so add that where needed.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This file does not need <pc.h> but does directly need
<linux/types.h>. Furthermore, arch/x86/lib/bios.c was getting <pci.h>
via <bios_emul.h> so add it there.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Align U-Boot image end to 8 bytes to make sure DT alignment requirement
is fulfilled. This fixes a possible failure in fdt_find_separate() in
case the U-Boot image is aligned to 4 Bytes and DT is appended at the
end at already 8 Byte aligned offset.
Link: https://source.denx.de/u-boot/u-boot/-/issues/30
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Marek Vasut <marek.vasut@mailbox.org>
|
|
Change the vcpumntirq in the GICv3 node from SPI to PPI.
Prevents Linux from complaining:
'[Firmware Bug]: CPU interface incapable of MMIO access'
Fixes: 6d722894fd48 "board: emulation: Add QEMU sbsa support"
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
|
|
RB1 and RB2 have three root compatibles where the last one can't be used
to decode fdtfile name (qcm* vs qrb*). So rather just rely on the first
compatible to retrieve the SoC name.
Signed-off-by: Sumit Garg <sumit.garg@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250505124333.12344-1-sumit.garg@kernel.org
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>
|
|
This reverts commit 027a316828528da95a77d20632370b1bc2823f0b as
discussed in [1].
[1] https://lists.denx.de/pipermail/u-boot/2025-May/590841.html
Signed-off-by: Mayuresh Chitale <mchitale@ventanamicro.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
|
|
This reverts commit 37b0b22d8b7bbed6aa95b6daed06dcbf4a66f211 as
discussed in [1].
[1] https://lists.denx.de/pipermail/u-boot/2025-May/590841.html
Signed-off-by: Mayuresh Chitale <mchitale@ventanamicro.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
|
|
The GW74xx D revision has added a M2SKT_WDIS2# GPIO which routes to the
W_DISABLE2# pin of the M.2 socket.
Add the iomux and a line name for this and rename the existing
m2_wdis# signal to m2_wdis1#.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
|
|
The Gateworks GW82XX-2X is an ARM based single board computer (SBC)
comprised of the i.MX8M Plus based gw702x SoM and the gw82xx
baseboard featuring:
- i.MX8M Plus SoC
- LPDDR4 DRAM
- eMMC FLASH
- Gateworks System Controller (GSC)
- microSD (1.8V/3.3V Capable)
- panel status bi-color LED
- pushbutton switch
- fan controller with tachometer
- USB Type-C connector
- PCIe switch
- 2x GbE RJ45 connectors
- multi-protocol RS232/RS485/RS422 Serial ports
- 2x Flexible Socket Adapters with SDIO/UART/USB/PCIe
(for M.2 and miniPCIe expansion)
- 2x isolated CAN
- GPS
- accelerometer
- magnetometer
- off-board connectors for: SPI, GPIO, I2C, ADC
- Wide range DC power input
- support for 802.3at PoE (via adapter)
Add support for it by providing its device-tree.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
|
|
Tom Rini <trini@konsulko.com> says:
In a private thread, Simon asked about what's needed to get PowerPC
migrated to DM_SERIAL. I went and took a look, and to complete the
entire DM_SERIAL migration (excluding SPL/TPL) we're actually nearly
there. This series first migrates PowerPC (and some NXP Layerscape
boards that share history more clearly with PowerPC parts), with the
biggest change being to make sure we still use the correct legacy
drivers in SPL/TPL (where SPL is extremely constrained). With that out
of the way, I looked at what was left. With two exceptions, it's
platforms which can be trivially enabled for conversion, and so we do
that.
Link: https://lore.kernel.org/r/20250502201226.1369013-1-trini@konsulko.com
|
|
Migrate the few ARM Layerscape platforms that had not been switched
along with all remaining PowerPC platforms to DM_SERIAL. For PowerPC,
this means that platforms which use SPL/TPL, keeping the non-DM serial
driver enabled there as they do not use DM. We also rework the guards
on how to define CFG_SYS_NS16550_CLK so that this is mostly in one place
now.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Manorit Chawdhry <m-chawdhry@ti.com> says:
Fix some of the boards that could be affected by the change done in [0].
[0]: https://lore.kernel.org/u-boot/20241121-b4-upstream-pll-fix-v1-0-904f618897a7@ti.com/T/#mecb70b415a364fdf322a94241438db7b5607e92b
Link: https://lore.kernel.org/r/20250515-b4-upstream-k3-pll-miss-v1-0-e38b89f027b8@ti.com
|
|
The commit 79d91e77f4c2 ("clk: ti: clk-k3-pll: Add additional robustness
steps to the PLL sequence") introduced a change which requires the
main_timer0 to not rely on it's own clocks which anyways was wrong.
Fix it by removing the clock dependency for it, also while at it, move
it from u-boot.dtsi to R5 as that is the only entity that should require
it as DM isn't up.
Fixes: 5d1aac358f3c ("arm: dts: k3-*-r5: Remove clocks from mcu_timer0")
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Acked-by: Wadim Egorov <w.egorov@phytec.de>
|
|
The commit 79d91e77f4c2 ("clk: ti: clk-k3-pll: Add additional robustness
steps to the PLL sequence") introduced a change which requires the
main_timer0 to not rely on it's own clocks which anyways was wrong.
Fix it by removing the clock dependency for it, also while at it, move
it from u-boot.dtsi to R5 as that is the only entity that should require
it as DM isn't up.
Fixes: 5d1aac358f3c ("arm: dts: k3-*-r5: Remove clocks from mcu_timer0")
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Acked-by: Francesco Dolcini <francesco.dolcini@toradex.com>
|
|
The commit 79d91e77f4c2 ("clk: ti: clk-k3-pll: Add additional robustness
steps to the PLL sequence") introduced a change which requires the
main_timer0 to not rely on it's own clocks which anyways was wrong.
Fix it by removing the clock dependency for it, also while at it, move
it from u-boot.dtsi to R5 as that is the only entity that should require
it as DM isn't up.
Fixes: 5d1aac358f3c ("arm: dts: k3-*-r5: Remove clocks from mcu_timer0")
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Tested-by: Wadim Egorov <w.egorov@phytec.de>
|
|
The commit 79d91e77f4c2 ("clk: ti: clk-k3-pll: Add additional robustness
steps to the PLL sequence") introduced a change which requires the
main_timer0 to not rely on it's own clocks which anyways was wrong.
Fix it by removing the clock dependency for it, also while at it, move
it from u-boot.dtsi to R5 as that is the only entity that should require
it as DM isn't up.
Fixes: 5d1aac358f3c ("arm: dts: k3-*-r5: Remove clocks from mcu_timer0")
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
|
