| Age | Commit message (Collapse) | Author |
|---|
|
The JH7110 SoC uses a GPIO for card detect.
* In the of_to_plat function check if a cd-gpios definition exists and
request the GPIO.
* In the getcd function return the GPIO value in this case.
Reported-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
|
|
After resetting the host controller, program in the POR val for this
register just like the Linux driver does.
This seems to help with initialization when running U-Boot as the primary
bootloader on some boards.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
Per JESD84-B51 P47, host need to change frequency to <=52MHz
after setting HS_TIMING to 0x1, and host need to set the
8-bit DDR buswidth. Currently setting the frequency to 26MHz
and trying to switch 8-bit DDR buswidth resulting timeouts.
mmc dev 1 0
Select HS400 failed -110
switch to partitions #0, OK
mmc1(part 0) is current device
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
|
|
Cadence SDMMC v6 controller has a lot of changes on initialize
compared to v4 controller. PHY is needed by v6 controller.
Signed-off-by: Kuan Lim Lee <kuanlim.lee@starfivetech.com>
Co-developed-by: Alex Soo <yuklin.soo@starfivetech.com>
Signed-off-by: Wei Liang Lim <weiliang.lim@starfivetech.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
Tim Harvey <tharvey@gateworks.com> says:
Modern eMMC v4+ devices have multiple hardware partitions per the JEDEC
specification described as:
Boot Area Partition 1
Boot Area Partition 2
RPMB Partition
General Purpose Partition 1
General Purpose Partition 2
General Purpose Partition 3
General Purpose Partition 4
User Data Area
These are referenced by fields in the PARTITION_CONFIG register
(Extended CSD Register 179) which is defined as:
bit 7: reserved
bit 6: BOOT_ACK
0x0: No boot acknowledge sent (default
0x1: Boot acknowledge sent during boot operation Bit
bit 5:3: BOOT_PARTITION_ENABLE
0x0: Device not boot enabled (default)
0x1: Boot Area partition 1 enabled for boot
0x2: Boot Area partition 2 enabled for boot
0x3-0x6: Reserved
0x7: User area enabled for boot
bit 2:0 PARTITION_ACCESS
0x0: No access to boot partition (default)
0x1: Boot Area partition 1
0x2: Boot Area partition 2
0x3: Replay Protected Memory Block (RPMB)
0x4: Access to General Purpose partition 1
0x5: Access to General Purpose partition 2
0x6: Access to General Purpose partition 3
0x7: Access to General Purpose partition 4
Note that setting PARTITION_ACCESS to 0x0 results in selecting the User
Data Area partition.
You can see above that the two fields BOOT_PARTITION_ENABLE and
PARTITION_ACCESS do not use the same enumerated values.
U-Boot uses a set of macros to access fields of the PARTITION_CONFIG
register:
EXT_CSD_BOOT_ACK_ENABLE (1 << 6)
EXT_CSD_BOOT_PARTITION_ENABLE (1 << 3)
EXT_CSD_PARTITION_ACCESS_ENABLE (1 << 0)
EXT_CSD_PARTITION_ACCESS_DISABLE (0 << 0)
EXT_CSD_BOOT_ACK(x) (x << 6)
EXT_CSD_BOOT_PART_NUM(x) (x << 3)
EXT_CSD_PARTITION_ACCESS(x) (x << 0)
EXT_CSD_EXTRACT_BOOT_ACK(x) (((x) >> 6) & 0x1)
EXT_CSD_EXTRACT_BOOT_PART(x) (((x) >> 3) & 0x7)
EXT_CSD_EXTRACT_PARTITION_ACCESS(x) ((x) & 0x7)
There are various places in U-Boot where the BOOT_PARTITION_ENABLE field
is accessed via EXT_CSD_EXTRACT_PARTITION_ACCESS and converted to a
hardware partition consistent with the definition of the
PARTITION_ACCESS field used by the various mmc_switch incarnations.
To add some sanity to the distinction between BOOT_PARTITION_ENABLE
(used to specify the active device on power-cycle) and PARTITION_ACCESS
(used to switch between hardware partitions) create two enumerated types
and use them wherever struct mmc * part_config is used or the above
macros are used.
Additionally provide arrays of the field names and allow those to be
used in the 'mmc partconf' command and in board support files.
The first patch adds enumerated types and makes use of them which
represents no compiled code change.
The 2nd patch adds the array of names and uses them in the 'mmc
partconf' command.
The 3rd patch uses the array of hardware partition names in a board
support file to show what emmc hardware partition U-Boot is being loaded
from.
|
|
eMMC v4+ devices have hardware partitions that are accessed via the
PARTITION_CONFIG (Extended CSD Register 179) PARTITION_ACCESS
and BOOT_PARTITION_ENABLE fields defined as:
bit 5:3: BOOT_PARTITION_ENABLE
0x0: Device not boot enabled (default)
0x1: Boot Area partition 1 enabled for boot
0x2: Boot Area partition 2 enabled for boot
0x3-0x6: Reserved
0x7: User area enabled for boot
bit 2:0 PARTITION_ACCESS
0x0: No access to boot partition (default)
0x1: Boot Area partition 1
0x2: Boot Area partition 2
0x3: Replay Protected Memory Block (RPMB)
0x4: Access to General Purpose partition 1
0x5: Access to General Purpose partition 2
0x6: Access to General Purpose partition 3
0x7: Access to General Purpose partition 4
Add char arrays to provide names for these values.
Use these names which displaying or setting the PARTITION_CONFIG
register via the 'mmc partconf' command.
Before:
u-boot=> mmc partconf 2 1 1 0 && mmc partconf 2
EXT_CSD[179], PARTITION_CONFIG:
BOOT_ACK: 0x1
BOOT_PARTITION_ENABLE: 0x2
PARTITION_ACCESS: 0x0
After:
u-boot=> mmc partconf 2 1 1 0 && mmc partconf 2
EXT_CSD[179], PARTITION_CONFIG:
BOOT_ACK: 0x1
BOOT_PARTITION_ENABLE: 0x1 (boot0)
PARTITION_ACCESS: 0x0 (user)
u-boot=> mmc partconf 2 1 boot1 0 && mmc partconf 2
EXT_CSD[179], PARTITION_CONFIG:
BOOT_ACK: 0x1
BOOT_PARTITION_ENABLE: 0x2 (boot1)
PARTITION_ACCESS: 0x0 (user)
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
|
|
Use the log subsystem instead of dev, to avoid including function names
in the code.
The CONFIG_LOGF_FUNC option can be used to enable the function name.
Update 'enhanced size' to use hex since this is the U-Boot default and
more natural for the large numbers involved.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
|
|
The code makes quite a few uses of __func__ which puts the function
name into the resulting SPL image. Use the log subsystem instead, to
reduce size.
The CONFIG_LOGF_FUNC option can be used to enable the function name.
Use lower-case hex for the status output in sdhci_transfer_data(), to
match sdhci_send_command()
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
|
|
Fix most of checkpatch warnings and other obvious style issues.
No functional change.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
Reduce U-Boot footprint by reusing dev->name as a driver's displayed
name. This changes boot device name (and "mmc info" output) from "EXYNOS
DWMMC" to something like "mmc@12100000".
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
add_dwmci() is already calling dwmci_setup_cfg() internally, there is no
needed to call dwmci_setup_cfg() again in case when add_dwmci() is used
(for non-DM cases). Fix it by calling dwmci_setup_cfg() only in DM
cases, when add_dwmci() wasn't called. Also, this assignment:
host->mmc = &plat->mmc;
is wrong in non-DM case when add_dwmci() was called, as it's creating
mmc object internally. Fix that by pulling that assignment into DM case,
when add_dwmci() isn't called.
While at it, add also this missing assignment:
host->mmc->dev = dev;
Fixes: 3537ee879e04 ("mmc: exynos_dw_mmc: support the Driver mode for Exynos")
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
There is no logical sense to split the initialization code between
multiple functions. Pull both do_dwmci_init() and
exynos_dwmci_core_init() into exynos_dwmmc_probe() to make the code more
simple and obvious.
No functional change.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
Add the compatible entry and corresponding chip data for Exynos7
compatible chips, which covers modern ARM64 based Exynos chips. They
have some differences w.r.t. old ARM32 Exynos chips:
- CLKSEL register offset is different
- 64-bit IDMAC descriptor and 64-bit IDMAC registers are used
(implemented in dw_mmc core driver)
In terms of the driver implementation, the CIU clock is obtained via CCF
framework (as opposed to ad-hoc clock driver implementation for ARM32
chips).
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
By now exynos_dw_mmc driver was relying on the correct CIU clock
frequency being set on driver init. But dw_mmc core is actually trying
to change CIU clock rate dynamically, on init and in set_ios() callback,
which it's requesting via host->get_mmc_clk() callback (the name is
misleading: although it's called "get_mmc_clk()", it can actually
request both get and set operations). Implement setting the requested
rate for CIU clock in Exynos driver to achieve the correct dw_mmc core
driver operation at all times. DDR mode requires the clock to be twice
as fast (when 8 bit bus is used), so handle this too, to make DDR
function properly.
This change makes the eMMC throughput on E850-96 board twice as fast.
That's because "clock-frequency" is set to 800 MHz in E850-96 device
tree, but for DDR52 mode it should be 416 MHz (and TRM states it should
be 400 MHz for DDR50/8bit mode). The dw_mmc core is requesting 52 MHz
bus_hz for DDR52 mode, and DDR+8bit mode means it should be x2 fast, so:
f_ciu = 2 * ciu_div * f_bus = 2 * 4 * 52e6 = 416 MHz,
where f_ciu - freq of clock fed to DW MMC block from CMU (SDCLKIN), Hz
f_bus - freq of clock fed to the card (CCLKIN), Hz
ciu_div - value of internal divider (in DW MMC block).
Another way to work that around would be overriding the
"clock-frequency" property in corresponding dts. But setting the clock
frequency dynamically as it's done here looks much neater.
This implementation follows what's done in Linux kernel dw_mmc-exynos
driver in .set_ios() callback for MMC_TIMING_MMC_DDR52 case.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
DDR timing values should be defined in "samsung,dw-mshc-ddr-timing" dts
property, and used when DDR MMC mode is selected. Read that value from
dts and use it. If it's not available, use SDR timing values instead.
This change is following upstream Linux kernel implementation.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
host->quirks field is only used internally in exynos_dw_mmc.c driver.
To avoid cluttering the scope of struct dwmci_host, move quirks field
into Exynos driver's chip data, where it can be statically defined.
No functional change.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
Instead of using non-standard "bus_hz" dts property, read common
"clock-frequency" property used in upstream Linux kernel. It's safe to
do so, as "clock-frequency" property was already added to corresponding
nodes in all affected Exynos device tree files.
No functional change.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
Instead of using non-standard "samsung,bus-width" dts property, read
common "bus-width" property used in upstream Linux kernel. It's safe to
do so, as "bus-width" property was already added to corresponding nodes
in all affected Exynos device tree files.
No functional change.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
Some chips like Exynos4412 have fixed internal CIU clock divider.
Instead of reading it from non-standard "div" dts property, store its
value in the driver internally, in static chip data associated with
corresponding compatible. This makes it possible to avoid using
host->div for storing it, so the latter can be removed safely. Also
create a helper function called exynos_dwmmc_get_ciu_div() for getting
the current div value: in case the fixed div is provided in the chip
data it will be used, otherwise the current div value is being read from
CLKSEL register.
The insights for this change were taken from dw_mmc-exynos.c driver in
Linux kernel.
No functional change.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
CLKSEL register offset may vary between different Exynos chips, e.g. on
ARM64 vs ARM32 chips. Provide a way to specify its offset value for each
compatible instead of hard-coding its value in read/write calls.
No functional change.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
The obsolete "samsung,timing" dts property is now split into
"samsung,dw-mshc-ciu-div" (for holding the internal DW MMC divider
value) and "samsung,dw-mshc-sdr-timing" (for actual timing values) in
upstream Linux kernel. Rework the driver to make use of new properties
instead of the old one. All affected dts files were already updated
accordingly.
No functional change.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
Update the driver to use livetree API instead of FDT one.
No functional change.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
exynos_dwmci_get_config() is called from the probe function and used to
read data from device tree. Make use of .of_to_plat driver callback
instead, and convert exynos_dwmci_get_config() to match its signature.
No functional change.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
New Exynos chips should implement clock drivers using CCF framework. In
that case corresponding CCF functions can be used to get/set the clock
rates. Moreover, already existing get_mmc_clk() and set_mmc_clk() calls
are only implemented for CONFIG_CPU_V7A (i.e. ARM32 chips). In case of
ARM64 chips that config option is not defined, so build will crash on
linking stage, with errors like these:
ld: drivers/mmc/exynos_dw_mmc.o:
in function `exynos_dwmci_get_sclk':
undefined reference to `get_mmc_clk'
ld: drivers/mmc/exynos_dw_mmc.o:
in function `exynos_dwmci_set_sclk':
undefined reference to `set_mmc_clk'
Fix that issue by using CCF clocks API on ARM64 platforms for getting
and setting the source clock (sclk = SDCLKIN = CIU) rate. To implement
this, first extract the existing ARM32 clock control code into helper
functions with more generic signatures to abstract getting/setting the
sclk rate. Then add CCF clock support to those functions for ARM64
platforms.
Fixes: a082a2dde061 ("EXYNOS5: DWMMC: Added FDT support for DWMMC")
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
Pinmux configuration on ARM64 platforms must be performed during startup
in pinctrl driver using info from device tree. exynos_pinmux_config()
and pinmux_decode_periph_id() are only available on ARM32 platforms, so
don't call those functions on ARM64 platforms. Instead of the latter
function, use "non-removable" property from device tree to derive the
dev_index value.
This fixes next linking errors on ARM64 platforms:
ld: drivers/mmc/exynos_dw_mmc.o:
in function `exynos_dwmci_get_config':
undefined reference to `pinmux_decode_periph_id'
ld: drivers/mmc/exynos_dw_mmc.o:
in function `do_dwmci_init':
undefined reference to `exynos_pinmux_config'
Fixes: a082a2dde061 ("EXYNOS5: DWMMC: Added FDT support for DWMMC")
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
In case of CONFIG_DM_MMC, host->priv actually holds (struct udevice *),
and not (struct dwmci_exynos_priv_data *). This makes *priv pointer
invalid and may lead to Synchronous Abort during its dereference later
in exynos_dwmci_board_init(). Fix it by extracting
exynos_dwmmc_get_priv() helper from exynos_dwmci_clksel() and using it
for getting the private data in exynos_dwmci_board_init()
Fixes: 3537ee879e04 ("mmc: exynos_dw_mmc: support the Driver mode for Exynos")
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
Getting the base address with outdated fdtdec_get_addr() API and further
casting it to (void *) leads to next build warning on ARM64 platforms:
In function 'exynos_dwmci_get_config':
warning: cast to pointer from integer of different size
[-Wint-to-pointer-cast]
host->ioaddr = (void *)base;
Use livetree API instead (dev_read_addr_ptr()), which handles this
correctly.
Fixes: a082a2dde061 ("EXYNOS5: DWMMC: Added FDT support for DWMMC")
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
Fix most of checkpatch warnings and other obvious style issues.
No functional change.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
Replace fifoth_val property with its fifo-depth counterpart in all DW
MMC drivers. fifo-depth is a common property used in upstream Linux
kernel. The FIFOTH register value will be calculated using fifo-depth
value in DW MMC core (dw_mmc.c). This change reduces code duplication in
platform drivers, and pulls common FIFOTH register value calculation
into core dw_mmc driver where it belongs.
No functional change.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
Some DW MMC blocks (e.g. those on modern Exynos chips) support 64-bit
DMA addressing mode. 64-bit DW MMC variants differ from their 32-bit
counterparts:
- the register layout is a bit different (because there are additional
IDMAC registers present for storing upper part of 64-bit addresses)
- DMA descriptor structure is bigger and different from 32-bit one
Introduce all necessary changes to enable support for 64-bit DMA capable
DW MMC blocks. Next changes were made:
1. Check which DMA address mode is supported in current IP-core
version. HCON register (bit 27) indicates whether it's 32-bit or
64-bit addressing. Add boolean .dma_64bit_address field to struct
dwmci_host and store the result there. dwmci_init_dma() function is
introduced for doing so, which is called on driver's init.
2. Add 64-bit DMA descriptor (struct dwmci_idmac64) and use it in
dwmci_prepare_desc() in case if .dma_64bit_address field is true.
A new dwmci_set_idma_desc64() function was added for populating that
descriptor.
3. Add registers for 64-bit DMA capable blocks. To make the access to
IDMAC registers universal between 32-bit / 64-bit cases, a new
struct dwmci_idmac_regs (and corresponding host->regs field) was
introduced, which abstracts the hardware by being set to
appropriate offset constants on init. All direct calls to IDMAC
registers were correspondingly replaced by accessing host->regs.
4. Allocate and use 64-bit DMA descriptors buffer in case when IDMAC
is 64-bit capable. Extract all the code (except for the IDMAC
descriptors buffer allocation) from dwmci_send_cmd() to
dwmci_send_cmd_common(), so that it's possible to keep IDMAC
buffer (either 32-bit or 64-bit) on stack during send_cmd routine.
The insights for this implementation were taken from Linux kernel DW MMC
driver.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
Prepare for adding 64-bit IDMAC descriptors by renaming current 32-bit
descriptor and its fields accordingly. While at it, make use of
virt_to_phys() to make it more obvious in which places the physical
addresses have to be used.
No functional change.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
Make dwmci_prepare_data() function easier to read by extracting the
preparation of IDMAC descriptor into a dedicated function.
No functional change.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
Make dwmci_send_cmd() easier to read by moving the DMA transfer handling
code into a dedicated function.
No functional change.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
FIFO data transfer is implemented as quite a massive chunk of code.
Extract it into a dedicated function to make dwmci_data_transfer()
easier to read and reduce the indentation level of the code.
No functional change.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
Extract the clock divider update into dwmci_update_div() function. It's
a procedure recommended in TRM, so it's better to keep it in a dedicated
function to make the code clearer.
While at it also extract the clock control code into a separate routine
to avoid code duplication in dwmci_setup_bus().
No functional change.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
Move FIFO threshold initialization into a separate function to make
dwmci_init() more readable.
No functional change.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
Waiting for data busy is a logically separate operation and should be
implemented as a separate routine. Follow Linux kernel example and
extract it from dwmci_send_cmd(). This way it doesn't clutter
dwmci_send_cmd() function, and can be reused later in other cases.
No functional change.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
struct idmac is only used in dw_mmc.c, so move it there from dwmmc.h to
avoid cluttering the interface in the header.
No functional change.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
Hosts capable of 8-bit can also do 4 bits, fix use of 4-bit mode when
8-bit mode is supported.
This fixes use of 1-bit mode with SD NAND on ROCK Pi S using the DT in
v6.11-rc1 that chage to use 8-bit bus to also support eMMC. With this
4-bit mode is used with SD NAND and 8-bit mode with eMMC, same as in
Linux kernel.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
There are no longer any OMAP4 platforms in U-Boot, remove the related
functionality.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Drop all duplicate newlines. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
|
The ARASAN MMC controller on Keystone 3 class of devices need the SDCD
line to be connected for proper functioning.
In cases where this can't be connected, add a quirk to force the
controller into test mode and set the TESTCD bit. Use the flag
"ti,fails-without-test-cd", to implement this above quirk when required.
Additionally, this quirk also avoids waiting for the controller debounce
time.
This commit is similar to linux kernel commit c7666240ec76
("drivers: mmc: sdhci_am654: Add the quirk to set TESTCD bit").
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
|
|
Christian Marangi <ansuelsmth@gmail.com> says:
This is an initial series that have all the initial trivial
fixes required for usage of OF_UPSTREAM for the mediatek SoC
This also contains the pcie-gen3 driver and the required tphy
support driver to make it work.
Subsequent series will follow with conversion of the mtk-clk
to permit usage of OF_UPSTREAM and upstream clk ID.
MT7981, MT7986 and MT7988 migration to upstream clock ID
is complete and working on MT7623.
Series CI tested with PR: https://github.com/u-boot/u-boot/pull/590
|
|
Add support for upstream linux clock and map U-Boot property to the one
use in upstream linux where supported.
Also add handling for the use_internal_cd that on upstream is hardcoded
enabled on mt7620.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
|
|
Add missing newline character and also add the return code of
regulator_set_value() to the output.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
|
|
https://source.denx.de/u-boot/custodians/u-boot-microblaze into next
AMD/Xilinx changes for v2024.10-rc1
common:
- spl: Introduce SoC specific init function
xilinx:
- Enable FF-A and NVMEM
- Rename spl_board_init() to spl_soc_init()
zynqmp:
- DT alignments
- Enable reset from SPL
- Enable USB3 for KD240
- Align multiboot register on Kria for proper reboot
- Allow multiboot environment write even in saved environment
- Move zynqmp commands from board/ to arch/
- Clean up xilinx_zynqmp.h
versal:
- Do not prioritize boot device if driver is not enabled
versal-net:
- Setup location for redundant variables in SPI
versal2:
- Add support for new SOC
mmc:
- Fix tap delay for SD on Versal NET
spi:
- Add SPI_NOR_OCTAL_READ flag for mx66uw2g345gx0 flash part
gpio:
- Cover MODEPIN firmware dependency
|
|
Enable tap delay programming for new SoC and also enable it via defconfig.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/f07daded9704cbc393657b65a28933c34a8cec25.1716994063.git.michal.simek@amd.com
|
|
I can't see any way how tap delays are setup on Versal NET platform because
xlnx,versal-8.9a compatible string is also used there but driver is not
letting to setup tap delays. Not sure if versal_iclk_phases[] is also valid
for Versal NET but the patch is made to investigate it.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/e535cfc1a59b5146a5c9a3ab389dc770de80440c.1713427490.git.michal.simek@amd.com
|
|
At this point in the DM migration, all platforms enable DM. BLK requires
DM. Make BLK "def_bool y" in the cases it had been "default y" to make
this clearer. Now remove the symbol requirement from other places as it
is redundant here.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
