summaryrefslogtreecommitdiff
path: root/drivers/mmc
AgeCommit message (Collapse)Author
2021-02-15Merge branch '2021-02-02-drop-asm_global_data-when-unused'Tom Rini
- Merge the patch to take <asm/global_data.h> out of <common.h>
2021-02-08mmc: mv_sdhci: parse device-tree entryBaruch Siach
Call mmc_of_parse() so that generic DT properties like 'non-removable' are taken into account. This fixes boot on Clearfog with eMMC on SOM that requires the non-removable property. Reported-by: Thorsten Spille <thorsten_spille@netcor.de> Signed-off-by: Baruch Siach <baruch@tkos.co.il> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com> Reviewed-by: Marek Behún <marek.behun@nic.cz>
2021-02-04mmc: am654_sdhci: Use sdhci_set_control_reg()Faiz Abbas
Use the generic sdhci_set_control_reg() instead of duplicating in platform driver. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Signed-off-by: Aswath Govindraju <a-govindraju@ti.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2021-02-04mmc: am654_sdhci: Fix HISPD bit configuration in some lower speed modesFaiz Abbas
According to the AM654x Data Manual[1], the setup timing in lower speed modes can only be met if the controller uses a falling edge data launch. To ensure this, the HIGH_SPEED_ENA (HOST_CONTROL[2]) bit should be cleared in default speed, SD high speed, MMC high speed, SDR12 and SDR25 speed modes. Use the sdhci writeb callback to implement this condition. [1] http://www.ti.com/lit/gpn/am6546 Section 5.10.5.16.1 Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Signed-off-by: Aswath Govindraju <a-govindraju@ti.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2021-02-04mmc: am654_sdhci: Add support for software tuningFaiz Abbas
With the new SW tuning App note[1], a custom tuning algorithm is required for eMMC HS200, HS400 and SD card UHS modes. The algorithm involves running through the 32 possible input tap delay values and sending the appropriate tuning command (CMD19/21) for each of them to get a fail or pass result for each of the values. Typically, the range will have a small contiguous failing window. Considering the tuning range as a circular buffer, the algorithm then sets a final tuned value directly opposite to the failing window. [1] https://www.ti.com/lit/pdf/spract9 Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Signed-off-by: Aswath Govindraju <a-govindraju@ti.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2021-02-04mmc: am654_sdhci: Add support for writing to clkbuf_selFaiz Abbas
Add support for writing new clock buffer select property for both the am654x and j721e 4 bit IPs Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Signed-off-by: Aswath Govindraju <a-govindraju@ti.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2021-02-04mmc: am654_sdhci: Add support for input tap delayFaiz Abbas
DLL need only be enabled for speed modes and clock frequencies at or above 50 MHz. For speed modes that don't enable the DLL, we need to configure a static input delay value. This involves reading an optional itap-del-sel-* value from the device tree and configuring it for the appropriate speed mode. Therefore, move all dll configurations to their own functions and gate it with 50 MHz speed and a minimum mode. If both these conditions are not satisfied then configure delay chain modes. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Signed-off-by: Aswath Govindraju <a-govindraju@ti.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2021-02-04mmc: am654_sdhci: Add support for AM65x SR2.0Faiz Abbas
Add Support for AM65x PG2.0. Use the SoC bus framework to fixup the platform data and do DLL calibration if the revision is 1.0 Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Signed-off-by: Aswath Govindraju <a-govindraju@ti.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2021-02-04mmc: am654_sdhci: Add flag for PHY calibrationFaiz Abbas
Not all controllers need calibration for the PHY DLL. Add a DLL_CALIB flag to indicate the same. Also move the write of trm_icp and driver strength to the set_clock() function to match the kernel configuration flow. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Signed-off-by: Aswath Govindraju <a-govindraju@ti.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2021-02-04mmc: am654_sdhci: Convert flag fields to BIT macroFaiz Abbas
Convert the flags field defines to use the BIT() macro. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Signed-off-by: Aswath Govindraju <a-govindraju@ti.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2021-02-04mmc: am654_sdhci: Unconditionally switch off DLL in the beginning of ios_post()Faiz Abbas
There are some speed modes that work without switching the dll on. Unconditionally switch off the DLL before setting clock frequency to support this case. The software will automatically enable DLL for speed modes that require it. This also means the dll_on priv data member is no longer required. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Signed-off-by: Aswath Govindraju <a-govindraju@ti.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2021-02-04mmc: sdhci: Add helper functions for UHS modesFaiz Abbas
Add a set_voltage() function which handles the switch from 3.3V to 1.8V for SD card UHS modes. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Signed-off-by: Aswath Govindraju <a-govindraju@ti.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2021-02-02common: Drop asm/global_data.h from common headerSimon Glass
Move this out of the common header and include it only where needed. In a number of cases this requires adding "struct udevice;" to avoid adding another large header or in other cases replacing / adding missing header files that had been pulled in, very indirectly. Finally, we have a few cases where we did not need to include <asm/global_data.h> at all, so remove that include. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@konsulko.com>
2021-01-31mmc: tmio: sdhi: Configure internal DMA bus widthMarek Vasut
The R-Car3 SDHI should set these two bits in DMA_MODE register according to the specification, to indicate 64bit bus width. No other bus width options are permitted and the default value is 0, which is incorrect. Set the bits accordingly. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
2021-01-27mmc: pci_mmc: Set the removable flagSimon Glass
Set this flag so that it is available to those looking at the device. For non-removable devices there is no need to check for insertion/removable since the media can never change. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2021-01-27mmc: pci_mmc: Only generate ACPI code for the SD cardSimon Glass
At present if an eMMC part is in the system, the ACPI table generated will include information about that, as well as the SD card. We only need to include the SD card, since it has a card-detect GPIO. Use a different compatible string for each option, and add code only for the SD card. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2021-01-27arm: mvebu: Espressobin: Disable slot when emmc is not presentPali Rohár
This change extends previous commit 061c6d1b238a ("arm: mvebu: Espressobin: Detect presence of emmc at runtime") and when emmc is not present then emmc is removed from U-Boot DM and corresponding slot is disabled. Therefore on Espressobin board without soldered emmc, state of emmc hw should be same as if emmc was disabled in DTS. Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
2021-01-25Merge https://gitlab.denx.de/u-boot/custodians/u-boot-sunxiTom Rini
- New Allwinner H616 SoC support (sans Ethernet & USB) - H6 DT update - Tanix TX6 TV box support - OrangePi 3 support - OrangePi Zero2 (H616) support
2021-01-25mmc: sunxi: Refactor mod clock register offsetAndre Przywara
So far the only difference between the various Allwinner MMC controller we are concerned about is the mod clock register offset. This is actually not directly related to the MMC controller IP, but an integration choice, dependent on the SoC this appears in. To avoid becoming trapped with some compatible fallback strings, let's remove the whole struct sunxi_mmc_variant, and replace this with a SoC based choice, which we can derive from the CONFIG_MACH_SUNx_y symbols. This will later simplify H616 support. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2021-01-25mmc: sunxi: Replace H6 ifdefs with H6 gen macroJernej Skrabec
It turns out that several SoCs share same mmc configuration as H6. In order to lower ifdef clutter replace H6 specific macro with common one. Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-01-25Merge tag 'mips-pull-2021-01-24' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-mips - MIPS: add support for Mediatek MT7620 SoCs
2021-01-25Merge tag 'u-boot-imx-20210125' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-imx Changes for 2020.04 ------------------- - new board: Phytec phyCORE-i.MX8MP i.MX8MN Beacon EmbeddedWorks devkit - Fixes: several nanbcb fixes fix for imx8mm_beacon - further switch to distro boot commands - DM: DM Ether for MX6UL CI: https://gitlab.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/6013
2021-01-24mmc: mtk-sd: assign plat->cfg.f_max with a correct valueWeijie Gao
Currently this driver does not set the value of plat->cfg.f_max, which results in that MMC framework will always run at the lowest frequency. This patch sets plat->cfg.f_max to the maximum allowed frequency, which equals to the source clock frequency. Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
2021-01-24mmc: mtk-sd: add pad control settings for MediaTek MT7620/MT76x8 SoCsWeijie Gao
The driver is missing pad control settings (pad delay and pad conf) for the mt7620 and mt76x8. Although mt76x8 still works well, mt7620 will encounter CRC error on data transfers. This patch adds default pad control settings for mt7620_compat. Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
2021-01-24mmc: mtk-sd: fix sclk cycles shift valueWeijie Gao
It turns out that the sclk cycles used by mt7620/mt7628 is the same as other chips (20 bits, 1048576), not 65536. This patch removes sclk_cycle_shift from dev_comp, and uses a macro with a value 20 instead. Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
2021-01-23mmc: fsl_esdhc_imx.c: fix compiler warningHeiko Schocher
prevent unsued variable compiler warning if DM_REGULATOR is not set. Signed-off-by: Heiko Schocher <hs@denx.de>
2021-01-22Merge https://gitlab.denx.de/u-boot/custodians/u-boot-samsung.gitTom Rini
2021-01-20mmc: xenon_sdhci: Remove duplicated macrosMichal Simek
There is no need to define the same macros in drivers. All macros have been added by commit 17a42abb40dd ("mmc: Define timing macro's"). Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2021-01-18mmc: fsl_esdhc_spl: remove superfluous free()Heinrich Schuchardt
Freeing a buffer before calling hang() is superfluous. Removing the call reduces the SPL size. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2021-01-18mmc: Only retrieve cd pin when GPIO is enabledHarm Berntsen
The driver only needs to retrieve the pin for the ACPI info. The driver itself works without depending on GPIO. Signed-off-by: Harm Berntsen <harm.berntsen@nedap.com> CC: Simon Glass <sjg@chromium.org> Reviewed-by: Simon Glass <sjg@chromium.org>
2021-01-15mmc: dwmmc: socfpga: Add ATF support for MMC driverChee Hong Ang
In non-secure mode (EL2), MMC driver calls the SMC/PSCI services provided by ATF to set SDMMC's DRVSEL and SMPLSEL. Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com> Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
2021-01-15mmc: dwmmc: Change designware MMC 'clksel' callback function to return statusSiew Chin Lim
Change 'clksel' callback function to allow the code to return a status. This patch is a preparation for enabling Arm-Trusted-Firmware (ATF) in Intel SoC FPGA. This patch does not change functionality. When using Arm-Trusted-Firmware (ATF) in Intel SoC FPGA, the MMC clock related register is secure register which is required to be written via SMC/PCSI call. It is possible that U-Boot fail to write the register if there is unexpected error between U-Boot and ATF. As a result, there maybe signal integrity on MMC connection due to clock. So, the code should reports error to user when 'clksel' fail. Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
2021-01-13mmc: stm32_sdmmc2: migrate trace to dev and log macroPatrick Delaunay
Define LOG_CATEGORY, use dev_ macro when it is possible. Remove the "%s:" __func__ header as it is managed by dev macro (dev->name is displayed) or log macro (CONFIG_LOGF_FUNC). Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2021-01-13mmc: exynos_dw_mmc: remove unused functionJaehoon Chung
Remove unused function in exynos_dw_mmc.c. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2021-01-05Merge tag 'dm-pull-5jan21' of git://git.denx.de/u-boot-dm into nextTom Rini
Driver model: make some udevice fields private Driver model: Rename U_BOOT_DEVICE et al. dtoc: Tidy up and add more tests ns16550 code clean-up x86 and sandbox minor fixes for of-platdata dtoc prepration for adding build-time instantiation
2021-01-05Merge tag 'v2021.01-rc5' into nextTom Rini
Prepare v2021.01-rc5 Signed-off-by: Tom Rini <trini@konsulko.com>
2021-01-05dm: Rename U_BOOT_DRIVER_ALIAS to DM_DRIVER_ALIASSimon Glass
We use the U_BOOT_ prefix (i.e. U_BOOT_DRIVER) to declare a driver but in every other case we just use DM_. Update the alias macros to use the DM_ prefix. We could perhaps rename U_BOOT_DRIVER() to DM_DRIVER(), but this macro is widely used and there is at least some benefit to indicating it us a U-Boot driver, particularly for code ported from Linux. So for now, let's keep that name. Signed-off-by: Simon Glass <sjg@chromium.org>
2021-01-05dm: core: Access device ofnode through functionsSimon Glass
At present ofnode is present in the device even if it is never used. With of-platdata this field is not used, so can be removed. In preparation for this, change the access to go through inline functions. Signed-off-by: Simon Glass <sjg@chromium.org>
2021-01-05dm: core: Use dev_has_ofnode() instead of dev_of_valid()Simon Glass
We have two functions which do the same thing. Standardise on dev_has_ofnode() since there is no such thing as an 'invalid' ofnode in normal operation: it is either null or missing. Also move the functions into one place. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
2021-01-05dm: core: Rename dev_has_of_node() to dev_has_ofnode()Simon Glass
We use 'ofnode' rather than 'of_node' in U-Boot. Rename this function to fit. Signed-off-by: Simon Glass <sjg@chromium.org>
2021-01-05dm: Use access methods for dev/uclass private dataSimon Glass
Most drivers use these access methods but a few do not. Update them. In some cases the access is not permitted, so mark those with a FIXME tag for the maintainer to check. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Pratyush Yadav <p.yadav@ti.com>
2020-12-22spi: spi-uclass: Fix spi_claim_bus() speed/mode setup logicOvidiu Panait
Currently, when different spi slaves claim the bus consecutively using spi_claim_bus(), spi_set_speed_mode() will only be executed on the first two calls, leaving the bus in a bad state starting with the third call. This patch drops spi_slave->speed member and adds caching of bus speed/mode in dm_spi_bus struct. It also updates spi_claim_bus() to call spi_set_speed_mode() if either speed or mode is different from what the bus is currently configured for. Current behavior is to only take into account the speed, but not the mode, which seems wrong. Fixes: 60e2809a848 ("dm: spi: Avoid setting the speed with every transfer") Reviewed-by: Simon Glass <sjg@chromium.org> Reported-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk> Reported-by: Moshe, Yaniv <yanivmo@amazon.com> Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
2020-12-18octeon: Don't attempt to set the sequence numberSimon Glass
Several Octeon drivers operate by setting the sequence number of their device. This should not be needed with the new sequence number setup. Also it is not permitted. Drop it. Signed-off-by: Simon Glass <sjg@chromium.org>
2020-12-18dm: Avoid accessing seq directlySimon Glass
At present various drivers etc. access the device's 'seq' member directly. This makes it harder to change the meaning of that member. Change access to go through a function instead. The drivers/i2c/lpc32xx_i2c.c file is left unchanged for now. Signed-off-by: Simon Glass <sjg@chromium.org>
2020-12-13dm: treewide: Rename ..._platdata variables to just ..._platSimon Glass
Try to maintain some consistency between these variables by using _plat as a suffix for them. Signed-off-by: Simon Glass <sjg@chromium.org>
2020-12-13dm: treewide: Rename ofdata_to_platdata() to of_to_plat()Simon Glass
This name is far too long. Rename it to remove the 'data' bits. This makes it consistent with the platdata->plat rename. Signed-off-by: Simon Glass <sjg@chromium.org>
2020-12-13dm: treewide: Rename dev_get_platdata() to dev_get_plat()Simon Glass
Rename this to be consistent with the change from 'platdata'. Signed-off-by: Simon Glass <sjg@chromium.org>
2020-12-13dm: treewide: Rename 'platdata' variables to just 'plat'Simon Glass
We use 'priv' for private data but often use 'platdata' for platform data. We can't really use 'pdata' since that is ambiguous (it could mean private or platform data). Rename some of the latter variables to end with 'plat' for consistency. Signed-off-by: Simon Glass <sjg@chromium.org>
2020-12-13dm: treewide: Rename auto_alloc_size members to be shorterSimon Glass
This construct is quite long-winded. In earlier days it made some sense since auto-allocation was a strange concept. But with driver model now used pretty universally, we can shorten this to 'auto'. This reduces verbosity and makes it easier to read. Coincidentally it also ensures that every declaration is on one line, thus making dtoc's job easier. Signed-off-by: Simon Glass <sjg@chromium.org>
2020-12-11Merge tag 'u-boot-atmel-fixes-2021.01-b' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-atmel Second set of u-boot-atmel fixes for 2021.01 cycle This set includes very important fixes for: MMC booting on several boards, drive strength on sam9x60ek mmc lines, compile issues for timer.c old driver, removal of unwanted access to sam9x60 bit for oscillator bypass mode, and eeproms read on sama5d2_icp.
generated by cgit v1.2.3 (git 2.0.4) at 2025-08-07 01:01:43 +0000