| Age | Commit message (Collapse) | Author |
|---|
|
Read PHY speed from hardware instead of assuming 100Mbps by default.
The TJA1103 works only at 100Mbps, but the driver will support more PHYs.
Signed-off-by: "Radu Pirea (NXP OSS)" <radu-nicolae.pirea@oss.nxp.com>
|
|
Use a local definition for the PHY features. PHY_100BT1_FEATURES are
not defined using the 100BaseT1 bit, so keep this workaround in the driver.
Signed-off-by: "Radu Pirea (NXP OSS)" <radu-nicolae.pirea@oss.nxp.com>
|
|
Some ethernet PHY require being reset before a phy-id can be read back
on the MDIO bus. This can result in the following message being show
on e.g. a Radxa ROCK Pi E v1.21 with a RTL8211F ethernet PHY.
Could not get PHY for ethernet@ff540000: addr -1
Add support to designware ethernet driver to reset eth phy by calling
the eth phy uclass function eth_phy_set_mdio_bus(). The call use NULL
as bus parameter to not set a shared mdio bus reference that would be
freed when probe fails. Also add a eth_phy_get_addr() call to try and
get the phy addr from DT when DM_MDIO is disabled.
This help fix ethernet on Radxa ROCK Pi E v1.21:
=> mdio list
ethernet@ff540000:
1 - RealTek RTL8211F <--> ethernet@ff540000
Reported-by: Trevor Woerner <twoerner@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
This ports the pad drive strength register configuration which can be
already found in the Linux driver for this PHY.
Signed-off-by: Lukasz Tekieli <tekieli.lukasz@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
|
|
This function is a no-op. Remove it.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Link: https://lore.kernel.org/r/20231216193843.2463779-3-seanga2@gmail.com
|
|
Make the "phy-handle" property optional, which allows support
for a fixed-link phy configuration.
Thus if the "phy-handle" is present in a DT, then driver will work as
before. Otherwise, phyaddr initialization will not be necessary,
as it is not needed in case of a fixed-link config.
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
|
|
Maxim Uvarov <maxim.uvarov@linaro.org> says:
Add small net fixes prior lwip patches.
|
|
debug print delays reset of the driver. Finally I see
bunch of "rx error FFFF" errors in the screen. CI can
not handle many prints. While network works fine there
Reproduced with:
make CROSS_COMPILE=sh2-linux- r2dplus_defconfig all
qemu-system-sh4 -M r2d -nographic -serial null \
-serial mon:stdio -net user,tftp=`pwd` \
-net nic,model=rtl8139 -kernel ./u-boot.bin
Signed-off-by: Maxim Uvarov <maxim.uvarov@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
return value of smc911x_send is ignored, but on sucesseful
send we need return 0 and or error -ETIMEOUT, not opposite.
Signed-off-by: Maxim Uvarov <maxim.uvarov@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
In order to make it easier to move on to dropping common.h from code
directly, remove common.h inclusion from the rest of the header file
which had been including it.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Port the mdio-mux-meson-gxl.c Linux driver introduced in [1],
and adapt it to U-Boot.
This driver is needed to boot U-Boot with Linux DT since v6.4,
since it switched the MDIO mux from the mmio to a proper GXL driver.
[1] 9a24e1ff4326 ("net: mdio: add amlogic gxl mdio mux support")
Link: https://lore.kernel.org/r/20231213-u-boot-gxl-mdio-mux-v2-1-c56bb02a75ea@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
|
|
https://source.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2024.04-rc1
zynqmp:
- Introduce Kria specific defconfig
- Calculate SPI image location based on boot offset
- DT updates
zynqmp-clk:
- Fix topsw_lsbus_clock for DP
axi-enet:
- Support older DT binding
mailbox:
- Add support for multiple mailboxes
pcie-xilinx:
- Covert driver to newer interface
- Enable MMIO region
zynq:
- dfu updates
- Enable capsule update for Antminer S9
- DT updates
xilinx_spi:
- Add new xfer callback and support runtime fifo depth discovery
|
|
Add support for the RTL8211F(D)(I)-VD-CG PHY present on the i.MX93 EVK
board.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
|
|
Add support for DWC EQoS MAC on i.MX93.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
|
|
As per the xlnx,axi-ethernet-1.00.a DT documentation in linux, the AXI
DMA registers can be obtained via the reg property or via a separate
node for the axistream DMA controller. Currently only the latter is
supported, so add support to fetch the DMA controller registers from the
"reg" property.
Signed-off-by: Mayuresh Chitale <mchitale@ventanamicro.com>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20231116164024.139934-1-mchitale@ventanamicro.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
|
|
Prepare v2024.01-rc3
|
|
DM_GPIO is always enable in U-Boot proper for ARCH_SUNXI, and this
driver is never enabled in SPL, so the condition is always true.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
|
|
Replace instances of http://www.ti.com with https://www.ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
|
|
In both include/fsl_qe.h and then also remove common.h from the files
which had included fsl_qe.h
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
There are no platforms which enable this feature, so remove it.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Older DesignWare Ethernet MAC versions that this driver supports can
only work with 32-bit DMA source/destination addresses. Some platforms
have no physical RAM at the lowest 4GB address space. For these
platforms the driver must translate DMA addresses to/from physical
memory addresses.
Call translation routines so that properly configured platforms can use
the DesignWare Ethernet MAC. For platforms using device-tree this
usually means adding dma-ranges property to the bus the device node is
in.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
|
|
e1000_eth_ids holds compatible strings for e1000 devices, but it
is meaningless as e1000 is a PCI device and there is no such
compatible string assigned to e1000 by the DT bindings community.
Drop it.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Setting the clock delay from the device tree settings
rx-internal-delay-ps and tx-internal-delay-ps was broken:
- The expected value in the device tree is suppose to be a
delay in picoseconds, but the driver only allowed an array index.
- Driver converted this array index to the actual delay in
picoseconds and tried to apply this in the device register. This
however is not a valid register value. The actual logic here was
reversed, it converted an register representation of the delay to
the device tree delay in picoseconds.
Only when the internal delays were NOT configured in the device tree
and they default value of 7 (=2000ps) was used, a valid value was
loaded in the register.
Signed-off-by: Frank de Brabander <debrabander@gmail.com>
|
|
It adds the driver for the internal MDIO bus of HIFEMAC Ethernet
controller. It's based on the mainstream linux driver.
Signed-off-by: Yang Xiwen <forbidden405@outlook.com>
|
|
It adds the driver for HIFEMAC Ethernet controller found on HiSilicon
SoCs like Hi3798MV200. It's based on the mainstream linux driver, but
quite a lot of code gets rewritten and cleaned up to adopt u-boot driver
model.
Signed-off-by: Yang Xiwen <forbidden405@outlook.com>
|
|
Marvell LinkStreet switches support Clause 45 MDIO on the internal bus.
C45 read or writes require the register address to be written first to
the SMI PHY Data register, and then a special C45 Write Address Register
OP is used on the SMI PHY Register before making a C45 Read Data Register
OP and being able to actually read the register.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
|
|
Driver is currently defining the mask and bit shifting itself,
there is no need for that as U-Boot has generic bitfield macros that help
us achieve the same result but in a cleaner way.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
|
|
Add optional reset control, especially for the Aspeed SOC. For the
hardware without a reset line, the reset assertion/deassertion will be
skipped.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
|
|
Set upper 32bit address for DMA descriptors and buffer address to support
64-bit addressing.
Signed-off-by: Ley Foon Tan <leyfoon.tan@starfivetech.com>
|
|
The CONFIG_MACPWR Kconfig symbol is used to point to a GPIO that enables
the power for the Ethernet "MAC" (mostly PHY, really).
In the DT this is described with the phy-supply property in the MAC DT
node, pointing to a (GPIO controlled) regulator. Since we need Ethernet
only in U-Boot proper, and use a DM driver there, we should use the DT
instead of hardcoding this.
Add code to the sun8i_emac and sunxi_emac drivers to check the DT for
that regulator and enable it, at probe time. Then drop the current code
from board.c, which was doing that job before.
This allows us to remove the MACPWR Kconfig definition and the respective
values from the defconfigs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Sam Edwards <CFSworks@gmail.com>
|
|
At the moment the sun4i EMAC driver relies on hardcoded CONFIG_MACPWR
Kconfig symbols to enable potential PHY regulators. As we want to get rid
of those, we need to find the regulator by chasing up the DT.
The sun4i-emac binding puts the PHY regulator into the MDIO node, which
is the parent of the PHY device. U-Boot does not have (and does not
need) an MDIO driver, so we need to chase down the regulator through the
EMAC node: we follow the "phy-handle" property to find the PHY node,
then go up to its parent, where we find the "phy-supply" link to the
regulator. Let U-Boot find the associated regulator device, and put that
into the private device struct, so we can find and enable the regulator
at probe time, later.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Sam Edwards <CFSworks@gmail.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
|
|
https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2024.01-rc1 v3
clk:
- remove additional compatible strings for Versal NET
net:
- zynq_gem: Fix clock calculation for MDC for higher frequencies
pinctrl:
- core: Extend pinmux status buffere size
- zynqmp driver: Show also tristate configuration
test:
- add test case for pxe get
Xilinx:
- describe SelectMAP boot mode
Zynq:
- Fix nand description in DT
ZynqMP:
- DTS sync patches with kernel and also W=1 related fixes
- Add support for KD240, zcu670, e-a2197 with x-prc cards, SC revB/C with i2c
description for other SC based boards
- k24 psu_init cleanup
|
|
As the xlnx,phy-type device tree property is deprecated and phy-mode
is being used, so removing the code references of xlnx,phy-type.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20231010030436.11854-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
|
|
Add support for declaring in device tree the reserved memory ranges
required for MC. Since the MC firmware acts as any DMA master present
in the SoC, the reserved memory ranges need also be identity mapped
in the SMMU, so create the required 'iommu-addresses' property in
the reserved memory nodes.
For now this support is used only on LX2160A SoCs.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
MDC clock change needs to be done when the driver probe function
is called as mdio is enabled at probe and not when the ethernet starts.
Setup the MDC clock at the probe itself.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20230922045010.22852-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
|
|
Add rk_gmac_ops and other special handling that is needed for GMAC to
work on RK3588.
rk_gmac_ops was ported from linux commits:
2f2b60a0ec28 ("net: ethernet: stmmac: dwmac-rk: Add gmac support for rk3588")
88619e77b33d ("net: stmmac: rk3588: Allow multiple gmac controller")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
|
|
Add a new glue driver for Rockchip SoCs, i.e RK3568, with a GMAC based
on Synopsys DWC Ethernet QoS IP.
rk_gmac_ops was ported from linux commit:
3bb3d6b1c195 ("net: stmmac: Add RK3566/RK3568 SoC support")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
|
|
Remove spam of RX packet not available debug messages when waiting to
receive a packet.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
|
|
Return error code when phy_connect fails or no link can be established.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
|
|
rx_pkt is allocated and not used for anything, remove it.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
|
|
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This old patch was marked as deferred. Bring it back to life, to continue
towards the removal of common.h
Move this out of the common header and include it only where needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
The NETSEC GMAC occasionally falls into a weird state where
MAC_REG_DESC_SOFT_RST has never been cleared and shows errors like the
below when networking commands are issued:
=> ping 192.168.1.1
ethernet@522d0000 Waiting for PHY auto negotiation to complete... done
netsec_wait_while_busy: timeout
Using ethernet@522d0000 device
ARP Retry count exceeded; starting again
ping failed; host 192.168.1.1 is not alive
It happens on not only 'ping' but also 'dhcp', 'tftp' and so on.
Luckily, restarting the NETSEC GMAC and trying again seems to fix the
problematic state. So first ensure that we haven't entered the state by
checking MAC_REG_DESC_SOFT_RST to be cleared; otherwise, restarting
NETSEC/PHY and trying again would work as a workaround.
Signed-off-by: Ryosuke Saito <ryosuke.saito@linaro.org>
Tested-by: Masahisa Kojima <masahisa.kojima@linaro.org>
|
|
Current code expects bridge phy address at 0 which is not correct
expectation because bridge phy address is configurable.
That's why update the code to read reg property to figure it out
where bridge is and use it in phy creation code.
Signed-off-by: Tejas Bhumkar <tejas.arvind.bhumkar@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20230915045043.4167628-1-tejas.arvind.bhumkar@amd.com
|
|
FDT functions is not working when OF_LIVE is enabled.
Convert fdt parsing functions to ofnode parsing functions.
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Link: https://lore.kernel.org/r/20230811074351.26916-1-fido_max@inbox.ru
|
|
The last user of the NEEDS_MANUAL_RELOC has been removed in commit
26af162ac8f8 ("arch: m68k: Implement relocation")
Remove now unused NEEDS_MANUAL_RELOC code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
|
The last user of the NEEDS_MANUAL_RELOC has been removed in commit
26af162ac8f8 ("arch: m68k: Implement relocation")
Remove now unused NEEDS_MANUAL_RELOC code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
|
The documentation for struct phy state that "The content of the
structure is managed solely by the PHY API and PHY drivers".
Change to use the generic_phy_valid() helper to check if phy is valid.
Fixes: 10c50b1facbf ("net: zynq: Add support for PHY configuration in SGMII mode")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
|
|
It's Broadcom PHY simply described as single-port
RGMII 10/100/1000BASE-T PHY. It requires disabling
delay skew and GTXCLK bits.
BCM54210E support ported from Linux kernel commit
0fc9ae1076697 ("net: phy: broadcom: add support for BCM54210E")
AUX/SHD/bcm54xx_config_clock_delay update ported from Linux 6.5-rc4 commit
28e219aea0b9e ("net: phy: broadcom: drop brcm_phy_setbits() and use phy_set_bits() instead")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Rafał Miłecki <rafal@milecki.pl>
|
|
The YT8511 ethernet PHYs can be found on e.g. the SOQuartz or
the Quartz64. Add rudimentary support for them.
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
|
