summaryrefslogtreecommitdiff
path: root/drivers/net
AgeCommit message (Collapse)Author
2021-01-31net: sun8i-emac: Determine pinmux based on SoC, not EMAC typeAndre Przywara
The pinmux choice for the RMII/RGMII pins the EMAC is connected to is not dependent on the EMAC IP, but on the SoC it is integrated in. Deriving the pinmux from the DT compatible string (as we do at the moment) will thus cause problems with certain EMAC IP / SoC combinations. To avoid this exact issue with the H616, let's use our Kconfig MACH symbols to choose the correct pinmux setup. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Tested-by: Jernej Skrabec <jernej.skrabec@siol.net> Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
2021-01-31net: sun8i-emac: Always clear syscon EPHY registerAndre Przywara
At the moment we only consider the EPHY register for those SoCs were we actually have an internal PHY to configure. However even other SoCs have this register, an expect the EPHY select bit to be cleared for proper operation with an external PHY. Rework sun8i_emac_set_syscon_ephy() to be called regardless of the EMAC model, and clear the H3_EPHY_SELECT bit if no internal PHY is used. We get away without it so far because SoCs like the A64 clear this bit on reset, but we need to explicitly clear it on the H616, for instance. The Linux driver does so as well. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Tested-by: Jernej Skrabec <jernej.skrabec@siol.net> Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
2021-01-27net: phy: micrel: Try default PHY ofnode firstMarek Vasut
The phydev structure has a PHY OF node pointer in it, use that OF node first when looking up PHY OF node properties, since that is likely the correct PHY OF node pointer. If the pointer is not valid, which is the case e.g. on legacy DTs, fall back to parsing MAC ethernet-phy subnode. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Ramon Fried <rfried.dev@gmail.com>
2021-01-27net: phy: ca_phy: Add driver for CAxxxx SoCsAbbie Chang
Add phy driver support for MACs embedded inside Cortina Access SoCs Signed-off-by: Abbie Chang <abbie.chang@cortina-access.com> Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com> CC: Joe Hershberger <joe.hershberger@ni.com> CC: Tom Rini <trini@konsulko.com> CC: Aaron Tseng <aaron.tseng@cortina-access.com> Moved out PHY specific code out of Cortina NI Ethernet driver and into a Cortina Access PHY interface driver
2021-01-27net: cortina_ni: Add eth support for Cortina Access CAxxxx SoCsAaron Tseng
Add Cortina Access Ethernet device driver for CAxxxx SoCs. This driver supports both legacy and DM_ETH network models. Signed-off-by: Aaron Tseng <aaron.tseng@cortina-access.com> Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com> Signed-off-by: Abbie Chang <abbie.chang@cortina-access.com> CC: Joe Hershberger <joe.hershberger@ni.com> CC: Abbie Chang <abbie.chang@Cortina-Access.com> CC: Tom Rini <trini@konsulko.com>
2021-01-27net: e1000: Add missing address translationsStefan Roese
Add some missing address translations from virtual address in local DRAM to physical address, which is needed for the DMA transactions to work correctly. This issue was detected while testing the e1000 driver on the MIPS Octeon III platform, which needs address translation. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Aaron Williams <awilliams@marvell.com> Cc: Chandrakala Chavva <cchavva@marvell.com>
2021-01-27net: e1000: Use virt_to_phys() instead of pci_virt_to_mem()Stefan Roese
Using (dm_)pci_virt_to_mem() is incorrect to translate the virtual address in local DRAM to a physical address. The correct macro here is virt_to_phys() so switch to using this macro. As virt_to_bus() is now not used any more, this patch also removes both definitions (DM and non-DM). This issue was detected while testing the e1000 driver on the MIPS Octeon III platform, which needs address translation. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Aaron Williams <awilliams@marvell.com> Cc: Chandrakala Chavva <cchavva@marvell.com>
2021-01-27net: e1000: Remove unused bus_to_phys() macroStefan Roese
bus_to_phys() is defined but not referenced at all. This patch removes it completely. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Aaron Williams <awilliams@marvell.com> Cc: Chandrakala Chavva <cchavva@marvell.com>
2021-01-25Merge https://gitlab.denx.de/u-boot/custodians/u-boot-sunxiTom Rini
- New Allwinner H616 SoC support (sans Ethernet & USB) - H6 DT update - Tanix TX6 TV box support - OrangePi 3 support - OrangePi Zero2 (H616) support
2021-01-25net: sun8i-emac: Allow all RGMII PHY modesAndre Przywara
So far all GBit users of the sun8i-emac driver were using the "rgmii" PHY mode, even though this turns out to be wrong. It just worked because the PHY driver doesn't do the proper setup (yet). In fact for most boards the "rgmii-id" or "rgmii-txid" PHY modes are the correct ones. To allow the DTs to describe the phy-mode correctly, and to stay compatible with Linux, at least allow those other RGMII modes in the driver. This avoids breakage if mainline DTs will be synced with U-Boot. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2021-01-25Merge tag 'mips-pull-2021-01-24' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-mips - MIPS: add support for Mediatek MT7620 SoCs
2021-01-25Merge tag 'u-boot-atmel-2021.04-b' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-atmel Second set of u-boot-atmel features for 2021.04 cycle This feature set includes macb updates for all interfaces and new sama7g5 variant support; micrel ksz9031 DLL support; a new board from Giant based on Adafruit feather form factor which contains a SAMA5D27 SoC; several fixes regarding the NAND flash PMECC block; and pincontrol drive strength support for pio4 controller.
2021-01-24net: add ethernet driver for MediaTek MT7620 SoCWeijie Gao
This patch adds ethernet driver for MediaTek MT7620 SoC. The MT7620 SoC has a built-in ethernet (Frame Engine) and a built-in 7-port switch and two xMII interfaces (can be MII/RMII/RGMII). The port 0-3 of the switch connects to intergrited FE PHYs. Port 4 can be configured to connect to either the intergrited FE PHY, or the xMII. Port 5 always connects to the xMII. Port 6 is the CPU port. This driver supports MT7530 giga switch connects to port 5. Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
2021-01-22net: macb: take into account all RGMII interface typesClaudiu Beznea
Take into account all RGMII interface types. Depending on it the RGMII PHY's timings are setup. Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
2021-01-22net: macb: add support for sama7g5 emacClaudiu Beznea
Add support for SAMA7G5 EMAC. Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
2021-01-22net: macb: add support for sama7g5 gmacClaudiu Beznea
Add support for SAMA7G5 GMAC. Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
2021-01-22net: macb: check clk_set_rate return value to be negativeClaudiu Beznea
clk_set_rate() returns the set rate in case of success and a negative number in case of failure. Consider failure only the negative numbers. Fixes: 3ef64444de157 ("dm: net: macb: Implement link speed change callback") Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
2021-01-22net: macb: add user io config data structureClaudiu Beznea
Different implementation of USER IO register needs different mapping for bit fields of this register. Add implementation for this and, since clken is part of USER IO and it needs to be activated based on per SoC capabilities, add caps in macb_config where clken specific information needs to be filled. Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
2021-01-19net: dwc_eth_qos: Pad descriptors to cacheline sizeMarek Vasut
The DWMAC4 IP has the possibility to skip up to 7 AXI bus width size words after the descriptor. Use this to pad the descriptors to cacheline size and remove the need for noncached memory altogether. Moreover, this lets Tegra use the generic cache flush / invalidate operations. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrice Chotard <patrice.chotard@st.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: Ramon Fried <rfried.dev@gmail.com> Cc: Stephen Warren <swarren@nvidia.com> Tested-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com> Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
2021-01-19net: ks8851: Reset internal RXFC count on bad packetMarek Vasut
A sporadic condition occurs when the "bad packet" error is triggered repeatedly, which results in "bad packet" messages scrolling on the console during transfer. To avoid triggering this, reset the internal RXFC count on the first occurance of the "bad packet", which forces the code to re-read the RX packet count from the MAC, and prevents any additional "bad packet" messages if there are no more packets in the MAC. Also print better debug information if this condition occurs. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Eugen Hristev <eugen.hristev@microchip.com> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Tom Rini <trini@konsulko.com>
2021-01-19net: ftgmac100: Read and retain MAC addressHongwei Zhang
Read and retain MAC address across flash and QEMU support. Signed-off-by: Hongwei Zhang <hongweiz@ami.com>
2021-01-19net: e1000: implement eth_write_hwaddr for DM_ETHIan Ray
Implement programming MAC address to the hardware also for device model configuration. Fixes: b565b18a294f ("board: ge: bx50v3: Enable DM for PCI and ethernet") Signed-off-by: Ian Ray <ian.ray@ge.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2021-01-19net: phy: micrel: fix typoClaudiu Beznea
Fix typo. Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
2021-01-19net: phy: micrel: add support for DLL setup on ksz9131Claudiu Beznea
Add support for DLL setup on KSZ9131. Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
2021-01-18net: macb: Add phy address to read it from device treePadmarao Begari
Read phy address from device tree and use it to find the phy device if not found then search in the range of 0 to 31. Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com> Reviewed-by: Anup Patel <anup.patel@wdc.com> Reviewed-by: Bin Meng <bin.meng@windriver.com> Tested-by: Bin Meng <bin.meng@windriver.com>
2021-01-18net: macb: Add DMA 64-bit address support for macbPadmarao Begari
Enable 32-bit or 64-bit DMA in the macb driver based on the macb hardware compatibility and it is configured with structure macb_config in the driver. The Microchip PolarFire SoC Memory Protection Unit(MPU) gives the 64-bit DMA access with the GEM, the MPU transactions on the AXI bus is 64-bit not 32-bit So 64-bit DMA is enabled for the Microchip PolarFire SoC GEM. Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com> Reviewed-by: Anup Patel <anup.patel@wdc.com> Tested-by: Bin Meng <bin.meng@windriver.com>
2021-01-15common: board_r: Drop initr_bbmii wrapperOvidiu Panait
Add a return value to bb_miiphy_init and use it directly in the post-relocation init sequence, rather than using a wrapper stub. Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2021-01-15net: designware: socfpga: Add ATF support for MAC driverChee Hong Ang
In non-secure mode (EL2), MAC driver calls the SMC/PSCI services provided by ATF to setup the PHY interface. Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com> Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
2021-01-05Merge tag 'dm-pull-5jan21' of git://git.denx.de/u-boot-dm into nextTom Rini
Driver model: make some udevice fields private Driver model: Rename U_BOOT_DEVICE et al. dtoc: Tidy up and add more tests ns16550 code clean-up x86 and sandbox minor fixes for of-platdata dtoc prepration for adding build-time instantiation
2021-01-05Merge tag 'v2021.01-rc5' into nextTom Rini
Prepare v2021.01-rc5 Signed-off-by: Tom Rini <trini@konsulko.com>
2021-01-05dm: core: Access device ofnode through functionsSimon Glass
At present ofnode is present in the device even if it is never used. With of-platdata this field is not used, so can be removed. In preparation for this, change the access to go through inline functions. Signed-off-by: Simon Glass <sjg@chromium.org>
2021-01-05dm: Use access methods for dev/uclass private dataSimon Glass
Most drivers use these access methods but a few do not. Update them. In some cases the access is not permitted, so mark those with a FIXME tag for the maintainer to check. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Pratyush Yadav <p.yadav@ti.com>
2020-12-18net: Update to use new sequence numbersSimon Glass
Checking for seq == -1 is effectively checking that the device is activated. The new sequence numbers are never -1 for a bound device, so update the check. Also drop the note about valid sequence numbers so it is accurate with the new approach. Signed-off-by: Simon Glass <sjg@chromium.org>
2020-12-18octeon: Don't attempt to set the sequence numberSimon Glass
Several Octeon drivers operate by setting the sequence number of their device. This should not be needed with the new sequence number setup. Also it is not permitted. Drop it. Signed-off-by: Simon Glass <sjg@chromium.org>
2020-12-18dm: Avoid accessing seq directlySimon Glass
At present various drivers etc. access the device's 'seq' member directly. This makes it harder to change the meaning of that member. Change access to go through a function instead. The drivers/i2c/lpc32xx_i2c.c file is left unchanged for now. Signed-off-by: Simon Glass <sjg@chromium.org>
2020-12-13dm: treewide: Rename ..._platdata variables to just ..._platSimon Glass
Try to maintain some consistency between these variables by using _plat as a suffix for them. Signed-off-by: Simon Glass <sjg@chromium.org>
2020-12-13dm: treewide: Rename ofdata_to_platdata() to of_to_plat()Simon Glass
This name is far too long. Rename it to remove the 'data' bits. This makes it consistent with the platdata->plat rename. Signed-off-by: Simon Glass <sjg@chromium.org>
2020-12-13dm: treewide: Rename dev_get_platdata() to dev_get_plat()Simon Glass
Rename this to be consistent with the change from 'platdata'. Signed-off-by: Simon Glass <sjg@chromium.org>
2020-12-13dm: treewide: Rename 'platdata' variables to just 'plat'Simon Glass
We use 'priv' for private data but often use 'platdata' for platform data. We can't really use 'pdata' since that is ambiguous (it could mean private or platform data). Rename some of the latter variables to end with 'plat' for consistency. Signed-off-by: Simon Glass <sjg@chromium.org>
2020-12-13dm: treewide: Rename auto_alloc_size members to be shorterSimon Glass
This construct is quite long-winded. In earlier days it made some sense since auto-allocation was a strange concept. But with driver model now used pretty universally, we can shorten this to 'auto'. This reduces verbosity and makes it easier to read. Coincidentally it also ensures that every declaration is on one line, thus making dtoc's job easier. Signed-off-by: Simon Glass <sjg@chromium.org>
2020-12-13dm: Remove uses of device_bind_offset()Simon Glass
This function is not needed since the standard device_bind() can be used instead. Signed-off-by: Simon Glass <sjg@chromium.org>
2020-12-13dm: core: Rename device_bind() to device_bind_offset()Simon Glass
This function is not necessary anymore, since device_bind_ofnode() does the same thing and works with both flattree and livetree. Rename it to indicate that it is special. Signed-off-by: Simon Glass <sjg@chromium.org>
2020-12-10net: pfe_eth: read PFE ESBC header flash with spi_flash_read APIBiwen Li
Read PFE ESBC header flash with spi_flash_read API - logs as follows, Net: SF: Detected s25fs512s with page size 256 Bytes, erase size 256 KiB, total 64 MiB "Synchronous Abort" handler, esr 0x96000210 elr: 000000008206db44 lr : 0000000082004ea0 (reloc) elr: 00000000b7ba6b44 lr : 00000000b7b3dea0 x0 : 00000000b79407e8 x1 : 0000000040640000 x2 : 0000000000000050 x3 : 0000000000000000 x4 : 000000000000000a x5 : 0000000000000050 x6 : 0000000000000366 x7 : 00000000b7942308 x8 : 00000000b76407c0 x9 : 0000000000000008 x10: 0000000000000044 x11: 00000000b7634d1c x12: 000000000000004f x13: 0000000000000044 x14: 00000000b7634d98 x15: 00000000b76407c0 x16: 0000000000000000 x17: 0000000000000000 x18: 00000000b7636dd8 x19: 0000000000000000 x20: 00000000b79407d0 x21: 00000000b79407e8 x22: 0000000040640000 x23: 00000000b7634e58 x24: 0000000000000000 x25: 0000000003800000 x26: 00000000b7bdd000 x27: 0000000000000000 x28: 0000000000000000 x29: 00000000b7634d10 Code: d2800003 eb03005f 54000101 d65f03c0 (f8636826) Resetting CPU ... Signed-off-by: Biwen Li <biwen.li@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-12-10armv8: lx2162a: Add Soc changes to support LX2162AMeenakshi Aggarwal
LX2162 is LX2160 based SoC, it has same die as of LX2160 with different packaging. LX2162A support 64-bit 2.9GT/s DDR4 memory, i2c, micro-click module, microSD card, eMMC support, serial console, qspi nor flash, qsgmii, sgmii, 25g, 40g, 50g network interface, one usb 3.0 and serdes interface to support three PCIe gen3 interface. Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com> [Fixed whitespace errors] Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-12-10drivers/net/phy: Add CORTINA_NO_FW_UPLOAD to KconfigMeenakshi Aggarwal
Move CORTINA_NO_FW_UPLOAD to Kconfig file so that it can be controlled via defconfig files. Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-11-09net: ks8851: Implement EEPROM MAC address readoutMarek Vasut
In case there is an EEPROM attached to the KS8851 MAC and the EEPROM contains a valid MAC address, the MAC address is loaded into the NIC registers on power on. Read the MAC address out of the NIC registers and provide it to U-Boot. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Eugen Hristev <eugen.hristev@microchip.com> Cc: Joe Hershberger <joe.hershberger@ni.com>
2020-10-29Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriqTom Rini
- Bug fixes and updates on vid, ls1088a lx2160a and other layerscape platforms. - Add optee_rpmb support for LX2 & Kontron sl28 support
2020-10-23net: lx2160a.c: Update to set ECx_PMUX precedenceRazvan Ionut Cirjan
As per hardware documentation, ECx_PMUX has precedence over SerDes protocol. For LX2160/LX2162 if DPMACs 17 and 18 are enabled as SGMII through SerDes protocol but ECx_PMUX configured them as RGMII, then the ports will be configured as RGMII and not SGMII. Signed-off-by: Razvan Ionut Cirjan <razvanionut.cirjan@nxp.com> [Rebased] Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-10-22Merge branch 'master' of https://gitlab.denx.de/u-boot/custodians/u-boot-sunxiTom Rini
- sun8i emac changes (Andre) - SCP firmware (Samuel)
2020-10-22net: Add IPQ40xx MDIO driverRobert Marko
This adds the driver for the IPQ40xx built-in MDIO. This will be needed to support future PHY driver. Signed-off-by: Robert Marko <robert.marko@sartura.hr> Cc: Luka Perkov <luka.perkov@sartura.hr>
generated by cgit v1.2.3 (git 2.0.4) at 2025-11-20 06:09:22 +0000