| Age | Commit message (Collapse) | Author |
|---|
|
There is a TX-FIFO and Shift Register empty(TFES) status
bit in spi controller. This commit checks the TFES bit
to wait the TX transfer completes.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Signed-off-by: Satoru Okamoto <okamoto.satoru@socionext.com>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
DMSTART bit must not be set while there is active transfer.
This commit sets the DMSTART bit only when the transfer begins.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Signed-off-by: Satoru Okamoto <okamoto.satoru@socionext.com>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
synquacer_cs_set() function does not wait the chip select
is deasserted when the driver sets the DMSTOP to deselect
the slave.
This commit checks the Slave Select Released(SRS) bit to wait
until the slave is deselected.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Signed-off-by: Satoru Okamoto <okamoto.satoru@socionext.com>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
"busy" variable is ORed without being initialized,
must be zeroed before use.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Signed-off-by: Satoru Okamoto <okamoto.satoru@socionext.com>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
Add Nuvoton BMC NPCM750 Pinmux and Pinconf support.
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
|
|
This loads a mac address using a misc device using the nvmem interface.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
|
|
This uses the nvmem API to load a mac address from an RTC.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This uses an i2c eeprom to load a mac address using the nvmem interface.
Enable I2C_EEPROM for sandbox SPL since it is the only sandbox config
which doesn't enable it eeprom.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This adds support for "nvmem cells" as seen in Linux. The nvmem device
class in Linux is used for various assorted ROMs and EEPROMs. In this
sense, it is similar to UCLASS_MISC, but also includes
UCLASS_I2C_EEPROM, UCLASS_RTC, and UCLASS_MTD. New drivers corresponding
to a Linux-style nvmem device should be implemented as one of the
previously-mentioned uclasses. The nvmem API acts as a compatibility
layer to adapt the (slightly different) APIs of these uclasses. It also
handles the lookup of nvmem cells.
While nvmem devices can be accessed directly, they are most often used
by reading/writing contiguous values called "cells". Cells typically
hold information like calibration, versions, or configuration (such as
mac addresses).
nvmem devices can specify "cells" in their device tree:
qfprom: eeprom@700000 {
#address-cells = <1>;
#size-cells = <1>;
reg = <0x00700000 0x100000>;
/* ... */
tsens_calibration: calib@404 {
reg = <0x404 0x10>;
};
};
which can then be referenced like:
tsens {
/* ... */
nvmem-cells = <&tsens_calibration>;
nvmem-cell-names = "calibration";
};
The tsens driver could then read the calibration value like:
struct nvmem_cell cal_cell;
u8 cal[16];
nvmem_cell_get_by_name(dev, "calibration", &cal_cell);
nvmem_cell_read(&cal_cell, cal, sizeof(cal));
Because nvmem devices are not all of the same uclass, supported uclasses
must register a nvmem_interface struct. This allows CONFIG_NVMEM to be
enabled without depending on specific uclasses. At the moment,
nvmem_interface is very bare-bones, and assumes that no initialization
is necessary. However, this could be amended in the future.
Although I2C_EEPROM and MISC are quite similar (and could likely be
unified), they present different read/write function signatures. To
abstract over this, NVMEM uses the same read/write signature as Linux.
In particular, short read/writes are not allowed, which is allowed by
MISC.
The functionality implemented by nvmem cells is very similar to that
provided by i2c_eeprom_partition. "fixed-partition"s for eeproms does
not seem to have made its way into Linux or into any device tree other
than sandbox. It is possible that with the introduction of this API it
would be possible to remove it.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
|
|
i2c_eeprom_ops->write uses a const buf, so use one for the wrapper
function as well.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Instead of reading a pseudo-rom mac address from the device tree, just use
whatever we get from write_hwaddr. This has the effect of using the mac
address from the environment (or from the device tree, if it is
specified).
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ramon Fried <rfried.dev@gmail.com>
|
|
Check the length of data written by the device is consistent with the
size of the buffers to avoid out-of-bounds memory accesses in case
values aren't consistent.
Signed-off-by: Andrew Scull <ascull@google.com>
Cc: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
The virtio-rng driver is extremely simple, making it suitable for
testing more of the virtio uclass logic. Have the sandbox driver bind
the virtio-rng driver rather than the virtio-blk driver so it can be
used in tests.
Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
The virtio sandbox transport was setting the device features value to
the bit index rather than shifting a bit to the right index. Fix this
using the bit manipulation macros.
Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
When the device returns used buffers, it should refer to the descriptor
that is the head of the descriptor chain for that buffer. Confirm this
to be the case by tracking the head of descriptor chains that have been
made available to the device.
Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
The shared descriptors should only be written by the guest driver,
however, the device is still able to overwrite and corrupt them.
Maintain a private shadow copy of the descriptors for the driver to
use for state tracking, removing the need to read from the shared
descriptors.
Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Move the logic for attaching a descriptor to its own function.
Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
The variables `total_sg` and `descs_used` have the same value. Replace
the few uses of `total_sg` with `descs_used` to simplify the situation.
Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
CONFIG_VAL(DEBUG_UART_BASE) expands to CONFIG_DEBUG_UART_BASE or
CONFIG_SPL_DEBUG_UART_BASE or CONFIG_TPL_DEBUG_UART_BASE and allows boards
to set different values for SPL, TPL and U-Boot Proper.
For ns16550 driver this support is there since commit d293759d55cc
("serial: ns16550: Add support for SPL_DEBUG_UART_BASE").
Signed-off-by: Pali Rohár <pali@kernel.org>
|
|
Add a check for calloc() failing to allocate the requested memory.
Make decode_regions() return an error code.
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Pierre-Clément Tosi <ptosi@google.com>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
access
CONFIG_MMC only initializes drivers for devices in UCLASS_MMC, we need
to initialize drivers for devices of type IF_TYPE_MMC in UCLASS_BLK as
well because they are the child devices of devices in UCLASS_MMC. This
is required for feature RPMB since it will access eMMC in optee-os.
Signed-off-by: Judy Wang <wangjudy@microsoft.com>
[trini: Add my SoB line and adjust Judy's name in git, having emailed
off-list]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
ARM semihosting provides no provisions for determining if there is
pending input. The only way to determine if there is console input is to
do a read (and block until the user types something). For this reason,
we always return true for tstc (since you will always get input if you
try). However, this behavior can cause problems for code which expects
tstc to eventually be empty. In query_console_serial, there is the
following construct:
/* empty input buffer */
while (tstc())
getchar();
with the current implementation, this effectively turns into an infinite
loop. To avoid this, fake tstc by returning false half of the time. This
is generally OK because the other common construct looks like
do {
if (tstc())
process(getchar());
} while (!timeout());
so it's fine if we only read a new character every other loop. This will
break things like CYGACC_COMM_IF_GETC_TIMEOUT, but that could be
reworked to test on the timeout instead of calling tstc again (and
ymodem over semihosted serial is not that useful in the first place).
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
|
|
Replace in the function of_machine_is_compatible(), the used API
fdt_node_check_compatible() by ofnode_device_is_compatible()
to support a live tree.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
Set correct type for 3rd argument of ofnode_get_addr_size_index_notrans()
function. It expects fdt_size_t * and not fdt_addr_t *.
When these two types do not have same size then U-Boot throw compile
warning:
drivers/mtd/mtdpart.c: In function ‘add_mtd_partitions_of’:
drivers/mtd/mtdpart.c:906:57: warning: passing argument 3 of ‘ofnode_get_addr_size_index_notrans’ from incompatible pointer type [-Wincompatible-pointer-types]
offset = ofnode_get_addr_size_index_notrans(child, 0, &size);
^~~~~
In file included from include/dm/device.h:13,
from include/linux/mtd/mtd.h:26,
from include/ubi_uboot.h:28,
from drivers/mtd/mtdpart.c:27:
include/dm/ofnode.h:530:25: note: expected ‘fdt_size_t *’ {aka ‘long long unsigned int *’} but argument is of type ‘fdt_addr_t *’ {aka ‘long unsigned int *’}
fdt_size_t *size);
~~~~~~~~~~~~^~~~
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
|
|
We have many cases of SPL (or TPL or VPL) drivers that don't depend on
SPL_MISC (and so on) but rather just MISC.
Cc: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
|
|
CONFIG_DM_EVENT without CONFIG_EVENT is non-functional.
Let CONFIG_DM_EVENT depend on CONFIG_EVENT.
Remove superfluous stub in include/event.h.
Fixes: 5b896ed5856f ("event: Add events for device probe/remove")
Reported-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
|
|
CONFIG_FIXED_SDHCI_ALIGNED_BUFFER is needed on some Marvell SoCs when
booting from MMC. All existing usages of this have the same value so
make this the default and have the Kconfig option depend on SPL &&
MVEBU_SPL_BOOT_DEVICE_MMC.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
This converts the following to Kconfig:
CONFIG_TPL_NAND_INIT
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
There are no platforms that set this, remove the code.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_SPL_COMMON_INIT_DDR
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_SPL_SYS_MALLOC_SIMPLE
The problem here is that a few platforms have been doing:
#ifdef CONFIG_SPL_BUILD
#define CONFIG_SYS_MALLOC_SIMPLE
#endif
instead of defining CONFIG_SPL_SYS_MALLOC_SIMPLE directly. Correct this
and update the documentation in a few places to match usage.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_SYS_CFI_FLASH_STATUS_POLL
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_SYS_FLASH_CFI_WIDTH
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This is always defined to 2, and referenced in two places. Move the
define to <asm/omap_common.h> and make sure the code that uses this
includes that file. Make <asm/arch-omap*/clock.h> not include that
file, as we don't need to be doing so.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
If the device fails to probe - for example, when there is no
ethaddr set - then the private data is automatically freed
but the mdiobus remains registered.
Fixes: 1e354cb39314 ("drivers: net: fsl_enetc: register internal MDIO bus")
Signed-off-by: Michael Walle <michael@walle.cc>
|
|
This driver depends on PCI. Update the Kconfig accordingly.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
|
|
https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2022.07-rc4
zynqmp:
- Fix DP PLL configuration for zcu102/zcu106 and SOM
- Fix split mode for starting R5s
- DT fixes
- Remove firmware node for mini configurations
- Wire TEE for multi DTB fit image
xilinx:
- Handle board_get_usable_ram_top(0) properly
phy:
- Extend psgtr timeout
mmc:
- Fix mini configuration which misses zynqmp_pm_is_function_supported()
|
|
The bulk of it is (finally!) some DT sync from the kernel. We refrained
from syncing one incompatible change, as this would spoil booting Linux
kernels before v5.13 with U-Boot's DT (via UEFI, for instance).
I test booted Linux v5.18 and v5.4 with that new DT on some boards, and
the headless peripherals (MMC, USB, Ethernet) seemed to work.
The rest are fixes:
- silencing missing clock warnings due to the new pinctrl driver
- fixing "UART0 on PortF", allowing UART access through the SD card pins
- add an F1C100s clock driver, to enable MMC support (SPI comes later)
- some cleanups for CONS_INDEX_n in Kconfig
Tested on BananaPi-M1, Pine64-LTS, Pine-H64, X96-Mate (H616) and
OrangePi-Zero.
|
|
Add support for i2c devices
|
|
These were only ever implied by sunxi platforms, and that usage has
been removed. Current practice is to specify CONFIG_CONS_INDEX in each
board's defconfig.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
|
|
Some devices enumerate various clocks in their DT, and many drivers
just blanketly try to enable all of them. This creates problems
since we only model a few gate clocks, and the clock driver outputs
a warning when a clock is not described:
=========
sunxi_set_gate: (CLK#3) unhandled
=========
Some clocks don't have an enable bit, or are already enabled in a
different way, so we might want to just ignore them.
Add a CCU_CLK_F_DUMMY_GATE flag that indicates that case, and define
a GATE_DUMMY macro that can be used in the clock description array.
Define a few clocks, used by some pinctrl devices, that way to suppress
the runtime warnings.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
|
|
The introduction of the DM pinctrl driver made its probe function enable
all clocks enumerated in the DT. This includes the "CLK_BUS_PIO" (and
variations) gate clock. Also CLK_PLL_PERIPH0 is used by the R_CCU device.
So far we didn't describe those clocks in our clock driver.
As we enable them already in the SPL, the devices happen to work, but
the clock driver still complains about not finding those clocks:
=========
sunxi_set_gate: (CLK#58) unhandled
=========
Add the one-liners that are needed to announce the gate bit for those
clocks, to silence that message on the console.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
|
|
H6 is from the sun50i family, not sun6i.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
|
|
Now that the pinmux conflict is handled in the board code (by skipping
setup for the one conflicting MMC controller), the driver does not need
to be entirely disabled based on the UART pinmux.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
|
|
Add the tpm2_tis_i2c driver that should support any TPMv2 compliant
I2C chips, such as the NPCT75X chip.
[Ilias rename priv_auto_alloc_size to priv_auto]
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
|
|
Commit 0980cbba7b3c ("mmc: fsl_esdhc_spl: pre-PBL: implement redundancy
support") changed number of sectors which are read but did not adjusted
error check.
Fix it and check for if correct number of sectors were read.
Fixes: 0980cbba7b3c ("mmc: fsl_esdhc_spl: pre-PBL: implement redundancy support")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
Now, spi_flash_probe_bus_cs() relies on DT for spi speed and mode
and logically calls spi_get_bus_and_cs(). In case spi mode and speed are
not read from DT, make usage of spi_flash_probe() instead.
To sum-up:
- Previous call tree was:
spi_flash_probe() -> spi_flash_probe_bus_cs() -> spi_get_bus_and_cs()
- Current call tree is:
spi_flash_probe() -> _spi_get_bus_and_cs()
spi_flash_probe_bus_cs() -> spi_get_bus_and_cs()
This patch impacts the following :
- cmd/sf.c: if spi mode and/or speed is passed in argument of
do_spi_flash_probe(), call spi_flash_probe() otherwise call
spi_flash_probe_bus_cs().
- drivers/net/fm/fm.c: as by default spi speed and mode was set to
0 and a comment indicates that speed and mode are read from DT,
use spi_flash_probe_bus_cs().
- drivers/net/pfe_eth/pfe_firmware.c: spi speed and mode are not read
from DT by all platforms using this driver, so keep legacy and replace
spi_flash_probe_bus_cs() by spi_flash_probe();
- drivers/net/sni_netsec.c : spi speed and mode are not read from DT,
so replace spi_flash_probe_bus_cs() by spi_flash_probe().
- drivers/usb/gadget/max3420_udc.c: Can't find any platform which make
usage of this driver, nevertheless, keep legacy and replace
spi_get_bus_and_cs() by _spi_get_bus_and_cs().
- env/sf.c: a comment indicates that speed and mode are read
from DT. So use spi_flash_probe_bus_cs().
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Marek Behun <marek.behun@nic.cz>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefan Roese <sr@denx.de>
Cc: "Pali Rohár" <pali@kernel.org>
Cc: Konstantin Porotchkin <kostap@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Pratyush Yadav <p.yadav@ti.com>
Cc: Sean Anderson <seanga2@gmail.com>
Cc: Anji J <anji.jagarlmudi@nxp.com>
Cc: Biwen Li <biwen.li@nxp.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Chaitanya Sakinam <chaitanya.sakinam@nxp.com>
|
|
Move legacy spi_get_bus_and_cs() code to _spi_get_bus_and_cs().
Add new spi_get_bus_and_cs() implementation which rely on DT
for speed and mode and don't need any drv_name nor dev_name
parameters. This will prepare the ground for next patch.
Update all callers to use _spi_get_bus_and_cs() to keep the
same behavior.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Marek Behun <marek.behun@nic.cz>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefan Roese <sr@denx.de>
Cc: "Pali Rohár" <pali@kernel.org>
Cc: Konstantin Porotchkin <kostap@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Pratyush Yadav <p.yadav@ti.com>
Cc: Sean Anderson <seanga2@gmail.com>
Cc: Anji J <anji.jagarlmudi@nxp.com>
Cc: Biwen Li <biwen.li@nxp.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Chaitanya Sakinam <chaitanya.sakinam@nxp.com>
|
|
Requesting the locality uses the timeout values, so they need
to be set beforehand.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-imx
u-boot-imx-20220523
-------------------
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/12087
Additionally to u-boot-imx20200520:
- DH MX8MP
- i.MX GPIO: reading GPIO when direction is output
- Menlo i.MX53: switch to DM
And from u-boot-imx20200520:
- fix Verdin hang
- add pca9450 regulator
- conversion to DM_SERIAL
- NAND block handling
- fix crypto
- enable cache on some boards
- add ACC board (MX6)
|
