| Age | Commit message (Collapse) | Author |
|---|
|
Set the speed requested through mpc8xx_spi_set_speed() instead
of hardcoding a fixed speed.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
|
|
On CPM, the RISC core is a lot more efficiant when doing transfers
in 16-bits chunks than in 8-bits chunks, but unfortunately the
words need to be byte swapped.
So, for large tranfers with an even size, allocate a temporary
buffer and byte-swap data before and after transfer.
This change allows setting higher speed for transfer. For instance
on an MPC 8xx (CPM1 comms RISC processor), the documentation tells
that transfer in byte mode at 1 kbit/s uses 0.200% of CPM load
at 25 MHz while a word transfer at the same speed uses 0.032%
of CPM load. This means the speed can be 6 times higher in
word mode for the same CPM load.
For small transfers, the load reduction is not worth the CPU load
required to allocate the temporary buffer, so do it only when data
size is over 64 bytes.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
|
|
Perform multiple transfer of size MAX_BUFFER when the data to be
transferred is longer than MAX_BUFFER.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
|
|
SDMA configuration register needs to be set up only once and doesn't
belong to drivers. Also, the value to be used is different on mpc885.
So do the init in cpu_init_f() with 0x40 for mpc885 and 0x1 for others.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
|
|
LM74 is a SPI temperature sensor.
Implement a driver to read temperature from it.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
|
|
xfer ops can be passed a NULL input or output buffer. At the
time being the driver ignores it and overwrites memory at 0.
Define a dummy buffer and use it when either input or output
buffer is NULL. Bail out when both are NULL as it shouldn't.
Also increase MAX_BUFFER len to 32k as the current is pretty
low.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
|
|
Since commit 773ad4ebb1d6 ("spi, mpc8xx: Add support for chipselect via
GPIO and fixups"), DM_GPIO is required for 8xx SPI.
Add the missing dependency to avoid build failures.
Fixes: 773ad4ebb1d6 ("spi, mpc8xx: Add support for chipselect via GPIO and fixups")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-imx
CI:
https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/20348
- Update the imx_rgpio2p to only access one address as per the
dt-schema.
- Remove unused imx9_cpu.c file.
- Only use the LPUART ipg clk for i.MX7ULP.
- Use the correct anatop base for accessing the PLL clocks on i.MX93.
|
|
|
|
The PLL clk needs use anatop base, otherwise wrong PLL address will
be used.
Fixes: 9c153e46661b ("clk: imx: add i.MX93 CCF driver")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
This was wrongly committed, no user, remove it.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
To i.MX7ULP compatible lpuart, there is only ipg clk, no per clk.
So add a devtype check for i.MX7ULP.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
The i.MX8ULP/93 gpio dt-schema have been updated to only have one
address entry, update the driver to support it.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Remove the unused argument about cmd_error.
Fixes: a3b2786651c7 ("mmc: Drop unused mmc_send_tuning() cmd_error parameter")
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
The value defaults to 0 and is ignored by dw_mmc code, so the other
users are not affected.
Setting this explicitly fixes some weird reading error found on Hi3798MV200.
Fixes: 8a5dc8140e62 ("mmc: hi6220_dw_mmc: add compatible for HC2910 support")
Signed-off-by: Yang Xiwen <forbidden405@outlook.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
As described in [1], some poor hardware or cards would fail to release
the bus and keep driving data lines low. Ignore it and send the next cmd
directly seems okay for most cases.
[1]: https://patchwork.kernel.org/project/linux-mmc/patch/1424458179-5456-1-git-send-email-dianders@chromium.org/
Signed-off-by: Yang Xiwen <forbidden405@outlook.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
CONFIG_DM_RESET enabled
This can avoid hardcoding a clock rate in driver. Also can enable the
clocks and deassert the resets if the pre-bootloader does not do this
for us.
Currently only enabled for Hi3798MV200.
Signed-off-by: Yang Xiwen <forbidden405@outlook.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
Place the SDR104/HS200/HS400 checks into the mmc_deinit() and always
call it. This simplifies the code and removes ifdeffery. No functional
change is expected.
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
|
|
Do not access SCC when sending commands during tuning operation as that
will disrupt the tuning operation. The tuning operation is adjusting the
SCC settings itself in execute_tuning callback.
When renesas_sdhi_execute_tuning() is called by the MMC core code, a loop
which consists of renesas_sdhi_prepare_tuning(), mmc_send_tuning() and
renesas_sdhi_compare_scc_data() iterates over each SCC tuning tap.
The renesas_sdhi_prepare_tuning() configures the SCC tuning tap number into
hardware, mmc_send_tuning() triggers transfer of tuning block which depends
on the bus mode for which the bus is currently being tuned, this information
is supplied by the MMC core code, and finally renesas_sdhi_compare_scc_data()
tests the received tuning block for validity.
Because renesas_sdhi_prepare_tuning() configures the SCC tuning tap into
the hardware to fit the tuning operation, mmc_send_tuning() which triggers
command transfer using renesas_sdhi_send_cmd() must not manipulate with
the SCC in any way. Currently renesas_sdhi_send_cmd() does unconditionally
call renesas_sdhi_check_scc_error(), which may adjust the SCC tuning tap
position by writing RENESAS_SDHI_SCC_TAPSET, which would overwrite the
required tuning configuration set by renesas_sdhi_prepare_tuning() and
disrupt the tuning operation.
Fix this by skipping the renesas_sdhi_check_scc_error() call in case the
MMC subsystem is in tuning state. This way, the SCC settings are left
unmodified by command transfer during tuning operation.
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Tested-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
Set generic mmc->tuning flag when performing tuning to indicate
this condition to drivers. Drivers may use this to bypass various
checks during tuning.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
This hs400_tuning is a flag, make it bool. No functional change.
This will be useful in the following patch, which adds another
more generic flag, where the compiler can better use the space
now reserved for the u8 to store more flags in it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
The current code uses the state of tuning block received by SCC to
determine whether or not to send transmission stop command. This is
not correct. Use the state of tuning block transfer to determine
whether or not to send transmission stop command instead, because
the transmission stop command has to be sent in case the tuning
block transfer failed.
This requires two changes, separate variable to store and check the
state of tuning block received by SCC, and another separate variable
to store and check return value from transmission stop command.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Tested-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
In case a CRC error occurs during DMA transfer, the transfer completion
flag is not set in TMIO_SD_DMA_INFO1 and the transfer would eventually
time out. The timeout could be very long in case the transfer consists
of a large amount of blocks, the base timeout is 10 seconds and every
block adds 100 us more.
In case a CRC error does occur, a completion flag is set in a different
register, TMIO_SD_INFO1. Use this other completion flag to detect DMA
transfer ended and stop waiting for TMIO_SD_DMA_INFO1 completion flag.
This reduces the lengthy timeout in case of an error. The unconditional
check of TMIO_SD_DMA_INFO2 register for DMA related errors must not be
skipped in any case to actually recognize the DMA error and report it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Tested-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
The cmd_error parameter is not used, remove it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
|
The PL180/MMCI driver is implied to use CONFIG_DM and the ARM
defconfigs such as configs/vexpress_ca9x4_defconfig will get it
as well.
With a simple oneline to default to not being the v2 variant,
the original ARM MMCI variant works fine with the driver as well.
The IP version actually needs to be read out from a register on
the ARM versions, but we will simply assume we are running on the
original hardware if arm,primecell-periphid is not explicitly
specified in the device tree.
Drop the !CONFIG_DM code and depend on DM_MMC.
Tested on the Versatile Express CA9x4 board.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
With MMC_PWRSEQ enabled the following link issue may happen when
building SPL and SPL_PWRSEQ is not enabled.
aarch64-linux-gnu-ld.bfd: drivers/mmc/meson_gx_mmc.o: in function `meson_mmc_probe':
drivers/mmc/meson_gx_mmc.c:295: undefined reference to `pwrseq_set_power'
Fix this by adding a SPL_MMC_PWRSEQ Kconfig option used to enable mmc
pwrseq support in SPL.
Also add depends on DM_GPIO to fix following link issue:
aarch64-linux-gnu-ld.bfd: drivers/mmc/mmc-pwrseq.o: in function `mmc_pwrseq_set_power':
drivers/mmc/mmc-pwrseq.c:26: undefined reference to `gpio_request_by_name'
aarch64-linux-gnu-ld.bfd: drivers/mmc/mmc-pwrseq.c:29: undefined reference to `dm_gpio_set_value'
aarch64-linux-gnu-ld.bfd: drivers/mmc/mmc-pwrseq.c:31: undefined reference to `dm_gpio_set_value'
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Ferass El Hafidi <vitali64pmemail@protonmail.com>
|
|
U-Boot does not support building kernel modules.
Fixes: 3c0dbed232bd ("mmc: arm_pl180_mmci: adapt driver to DM usage")
Fixes: 36645f45a048 ("drivers: mmc: Add sdhci driver for Broadcom iProc platform")
Fixes: dadd43c14368 ("mmc: synquacer: Add SynQuacer F_SDH30 SDHCI driver")
Fixes: b312c590bcd8 ("mmc: Add MMC support for stm32h7 Socs")
Fixes: d24b69395949 ("mmc: mtk-sd: add SD/MMC host controller driver for MT7623 SoC")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
If the CSD register contains a reserved value (4 - 7) in bits 0:2 of the
TRAN_SPEED field, a buffer overrun occurs. Resize the mapping table.
According to the original report
https://lore.kernel.org/u-boot/20180826231332.2491-11-erosca@de.adit-jv.com/
reserved values have been observed resulting in a buffer overrun.
Reported-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Fixes: 272cc70b211e ("Add MMC Framework")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
CONFIG_SPL_SOCFPGA_DT_REG
Commit 3f190c55a4211215914126b74357344342329943
("drivers: misc: Add socfpga_dtreg driver for Intel SoCFPGA")
This commit rename CONFIG_SPL_SOCFPGA_SEC_REG to CONFIG_SPL_SOCFPGA_DT_REG
in Makefile.
Signed-off-by: Wan Yee Lau <wan.yee.lau@intel.com>
|
|
|
|
https://source.denx.de/u-boot/custodians/u-boot-nand-flash
The first patch is by Weizhao Ouyang and avoids sf probe crashes.
The second patch is by Arseniy Krasnov and adds basic support for Amlogic
Meson NAND controller on AXG.
The following four patches are by Alexander Dahl and apply some fixes to
drivers/mtd/nand/raw/ and port some changes applied in Linux.
The following patch is by Bruce Suen and adds support for XTX SPINAND.
Finally, the last patch is again by Arseniy Krasnov and adds access to
OTP region, supporting info, dump, write and lock operations.
|
|
Add support for XTX XT26G0xA and XT26xxxD. The driver is ported from
linux-6.7.1. This driver is tested on Banana BPI-R3 with XT26G01A and
XT26G12D.
Link: https://lore.kernel.org/all/20240312014314.15454-1-bruce_suen@163.com
Signed-off-by: Bruce Suen <bruce_suen@163.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
|
|
Introduced with commit 6a8dfd57220d ("nand: atmel: Add DM based NAND
driver") when driver was initially ported from Linux. The context
around this and especially the code itself suggests 'read' is meant
instead of write.
The fix is the same as accepted in Linux already with mainline Linux
kernel commit 1c60e027ffde ("mtd: nand: raw: atmel: Fix comment in
timings preparation").
Link: https://lore.kernel.org/all/20240320090214.40465-6-ada@thorsis.com
Link: https://lore.kernel.org/linux-mtd/20240307172835.3453880-1-miquel.raynal@bootlin.com/T/#t
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
|
|
One tab in general. One tab plus two spaces for help text.
Link: https://lore.kernel.org/all/20240320090214.40465-4-ada@thorsis.com
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
|
|
Introduced in upstream Linux with commit 7a08dbaedd365 for release v5.0.
When the new atmel nand driver was backported to U-Boot with commit
6a8dfd57220d ("nand: atmel: Add DM based NAND driver") that definition
was added to the driver instead of the header file. Move it over to the
other definitions with the same help text it has in Linux.
Code actually using this has not been ported over to raw nand base yet.
Link: https://lore.kernel.org/all/20240320090214.40465-3-ada@thorsis.com
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
|
|
In every other place in this file the macro is used, make it consistent.
Link: https://lore.kernel.org/all/20240320090214.40465-2-ada@thorsis.com
Fixes: 9d1806fadc24 ("mtd: nand: Get rid of mtd variable in function calls")
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
|
|
Basic support for Amlogic Meson NAND controller on AXG. This version
works at only first EDO mode.
Based on Linux version 6.7.0-rc4.
Link: https://lore.kernel.org/all/20240210223927.570043-1-avkrasnov@salutedevices.com
Signed-off-by: Arseniy Krasnov <avkrasnov@salutedevices.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
|
|
Allowing multicast packets is required for IPv6 neighbor discovery
protocol.
Signed-off-by: Parvathi Bhogaraju <pbhogaraju@microsoft.com>
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
|
|
In IPv6 context, the ICMP and UDP checksum byte in the RX packet
is initially set to 0, recaclculated, and then re-inserted.
This process can result in a dirty cache line. To prevent issues,
it is essential to invalidate cache for the RX buffer before freeing
the descriptor for next DMA transfer.
This ensure that the dirty cache line doesn't inadvertently written back
due to cache eviction, there by corrupting the RX buffer
Signed-off-by: Parvathi Bhogaraju <pbhogaraju@microsoft.com>
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
|
|
Fix compilation warning:
../arch/arm/include/asm/io.h: In function 'eqos_free_pkt':
../arch/arm/include/asm/io.h:103:32: warning: 'rx_desc' may be used uninitialized [-Wmaybe-uninitialized]
103 | #define writel(v,c) ({ u32 __v = v; __iowmb(); __arch_putl(__v,c); __v; })
| ^~~
../drivers/net/dwc_eth_qos.c:1220:27: note: 'rx_desc' was declared here
1220 | struct eqos_desc *rx_desc;
| ^~~~~~~
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
MD Danish Anwar <danishanwar@ti.com> says:
Introduce ICSSG PRUETH support in uboot. The ICSSG driver is used in TI
AM654 SR2.0.
The ICSSG PRU Sub-system runs on EMAC firmware. This series Introduces
support for ICSSG driver in uboot.
This series has been tested on AM65x SR2.0, and the ICSSG interface is
able to ping / dhcp and boot kernel using tftp in uboot.
To use ICSSG2 ethernet, the ICSSG firmware needs to be loaded to PRU RPROC
cores and RPROC cores need to be booted with the firmware. This step is
done inside driver similar to kernel.
The remoteproc driver uses request_fw_into_buf() API from fs-loader driver
to load and start rproc with the required firmwares.
This series only introduces driver files. The device tree and config
changes to enable ICSSG driver will be introduced later.
|
|
ICSSG firmware supports FDB commands. Add support to send FDB commands
from driver. Once rx_flow_id is obtained from dma, let firmware know that
we are using this rx_flow_id by sending a FDB command.
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
|
|
This is the PRUSS Ethernet driver for TI AM654 SR2.0 and later SoCs with
the ICSSG PRU Sub-system running EMAC firmware. ICSSG Subsystem supports
two slices per instance. This driver caters to both slices / ports of
the icssg subsystem.
Since it is not possible for Ethernet driver to register more than one
port for a given instance, this patch introduces top level PRUETH as
UCLASS_MISC and binds UCLASS_ETH to individual ports in order to support
bringing up more than one Ethernet interface in U-Boot.
Since top level driver is UCLASS_MISC, board files would need to
instantiate the driver explicitly.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
|
|
Add icssg_queue.c file. This file introduces macros and APIs related to
ICSSG queues. These will be used by ICSSG Ethernet driver.
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
|
|
Add icssg_config.h / .c and icssg_classifier.c files. These are firmware
configuration and classification related files. Add MII helper APIs and
MACROs. These APIs and MACROs will be later used by ICSSG Ethernet driver.
Also introduce icssg_prueth.h which has definition of prueth related
structures.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
|
|
Add firmware interface related headers and macros for ICSSG Ethernet
driver. These macros will be later used by the ICSSG ethernet driver.
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
|
|
The sysreset TI-SCI API is available with TI-SCI always, there is no need
for a DT node to describe the availability of this. If the sysreset driver
is available then bind it during ti-sci probe.
Remove the unneeded device tree matching.
Signed-off-by: Andrew Davis <afd@ti.com>
Tested-by: Jonathan Humphreys <j-humphreys@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
|
|
The device name is a concatenation of the device node name of the cpsw
device and of the device node name of the port. In my case that is
ethernet@8000000
port@1
First the buffer is really too small, but more importantly, there is no
boundary check. Use snprintf() and increase the buffer size.
Fixes: 38922b1f4acc ("net: ti: am65-cpsw: Add support for multi port independent MAC mode")
Signed-off-by: Michael Walle <mwalle@kernel.org>
|
|
Simon Glass <sjg@chromium.org> says:
This little series reprises the EFI-video fix, fixes a USB problem and
enables a boot script for coreboot.
It also moves to truetype fonts for coreboot and qemu-x86, since the
menus look much better and there are no strong size constraints.
With these changes it is possible to boot a Linux distro automatically
with U-Boot on x86, including when U-Boot is the second-stage
bootloader.
|
|
This is needed to support Truetype fonts. In any case, the compiler
expects SSE to be available in 64-bit mode. Provide an option to enable
SSE so that hardware floating-point arithmetic works.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Suggested-by: Bin Meng <bmeng.cn@gmail.com>
|
