| Age | Commit message (Collapse) | Author |
|---|
|
Anurag Dutta <a-dutta@ti.com> says:
Hi All,
In u-boot, hbmc is broken and has been removed from j7200
configs. This series re-enables the hbmc driver and introduces a series
of hyperflash boot fixes. At present, in u-boot, the parent device (fss)
gets registered as a syscon device. This is done because the MMIO
mux driver in u-boot did not support the mux functionality when the
parent device is not a syscon. In this series, we make relevant changes
in the hbmc driver as well as dts' so that we can use the reg-mux driver for
selecting the appropriate state of the mux.
Test logs:
1) j721e-idk-gw hyperflash boot test: https://gist.github.com/anuragdutta731/50aae6fec707a3ffad6d985de6757fe4
2) j7200-evm hyperflash boot test: https://gist.github.com/anuragdutta731/c3a4d60f8bfd9c425d6c44b36eb7322b
Link: https://lore.kernel.org/r/20241129113136.383277-1-a-dutta@ti.com
|
|
The HBMC_AM654 driver was dependent on SYSCON because syscon APIs were
being used to select the multiplexer state. Change the dependency to
MULTIPLEXER and MUX_MMIO because mux APIs are now being used to
select mux state.
Signed-off-by: Anurag Dutta <a-dutta@ti.com>
|
|
The syscon APIs were used for selecting the state of the mux
device because the mmio-mux driver in u-boot did not support
the mux functionality when the parent device is not a syscon.
Change to mux APIs which utilizes the reg-mux driver to select the
state of the multiplexer.
Signed-off-by: Anurag Dutta <a-dutta@ti.com>
|
|
Add config required to build mmio-mux driver and dependencies.
Signed-off-by: Anurag Dutta <a-dutta@ti.com>
|
|
Gokul Praveen <g-praveen@ti.com> says:
The OMAP specific UART driver is changed from a generic implementation of
certain ops functions to an OMAP specific implementation of it to add
support for higher baudrates for OMAP devices.
Hence to support the above change, static functionality of ops functions
in generic ns16550 UART U-Boot driver is removed and also migrated certain
macros to its header file for usage in device-specific drivers.
Boot logs link :
https://gist.github.com/GOKU-THUG/8b90117c963e5da5c1b6caeee427c82c
Link: https://lore.kernel.org/r/20241126105131.43359-1-g-praveen@ti.com
|
|
higher baudrates
Move to OMAP specific implementation of certain ops functions as the UART
prints on the serial console fail for baudrates greater than 460800.
The MDR1 register is responsible for determining the speed mode at which
the UART should operate for OMAP specific devices. The baud divisor is used
to set the UART_DLL register which is used for generation of the baud
clock in the baud rate generator. The implementation logic is similar to
how it is implemented in omap_8250_get_divisor function of 8250_omap UART
linux driver.
Signed-off-by: Gokul Praveen <g-praveen@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Increase scope of ops functions and do some clean up for usage in device
-specific UART drivers.
Remove the static functionality of ops functions and migrate certain macros
to header file for usage in device-specific drivers.
Signed-off-by: Gokul Praveen <g-praveen@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Siddharth Vadapalli <s-vadapalli@ti.com> says:
Hello,
This series adds support for USB DFU boot on TI's AM62A SoC which has
two instances of DWC3 USB Controllers namely USB0 and USB1. The USB0
instance of the USB Controller supports USB DFU boot:
ROM => tiboot3.bin => tispl.bin => u-boot.img
USB DFU Boot requires the USB Controller to be configured for Gadget
mode of operation. Since the USB0 instance of the DWC3 USB Controller
supports both Host and Gadget modes of operation via the Type-C interface
on the AM62A7-SK board, the device-tree specifies the "dr_mode" as "OTG".
However, there is currently no support for dynamically switching the "mode"
from Host to Gadget and vice-versa with the help of a state-machine.
The OTG mode is treated as a separate mode in itself rather than being
treated as an intermediate stage before assuming the Host/Gadget mode.
Due to this, USB DFU boot via the Type-C interface doesn't work as the
USB Controller hasn't been appropriately configured for Device/Gadget
mode of operation. One option is to change the device-tree to specify
"dr_mode" as "peripheral" and force the controller to assume the Device
role. This will imply that the U-Boot device-tree for AM62A diverges
from its Linux counterpart. Therefore, with the intent of keeping the
device-tree uniform across Linux and U-Boot, and at the same time, in
order to enable USB DFU boot in "OTG" mode with the DWC3 Controller,
the first patch in this series sets the "mode" on the basis of the
caller function, rather than using the "dr_mode" property in the
device-tree. There are only two callers of "dwc3_generic_probe()",
each of which clearly specify the expected mode of configuration.
This will enable both Host and Device mode of operation based on the
command executed by the user, thereby truly supporting "OTG"
functionality when the USB Controller supports it.
The second patch in this series adds USB DFU environment for AM62A,
enabling USB DFU Boot and USB DFU flash on AM62A.
In addition to the patches in this series, the following device-tree
changes will be required to test USB DFU on AM62A (bootph-all property
to be added to ensure that USB Controller is present at all stages
for DFU Boot):
https://gist.github.com/Siddharth-Vadapalli-at-TI/53ba02cb0ff4a09c47e920d08247065f
The above device-tree changes will be made to the Linux device-tree,
which shall ensure that the same shall be a part of U-Boot device-tree
eventually.
The USB DFU config fragments for AM62x have been used for enabling
USB DFU boot on AM62a as follows:
R5 => am62ax_evm_r5_defconfig + am62x_r5_usbdfu.config
A53 => am62ax_evm_a53_defconfig + am62x_a53_usbdfu.config
Logs validating USB DFU boot with this series:
https://gist.github.com/Siddharth-Vadapalli-at-TI/daa71da1b0e478a51afea42605fb2d2c
Link: https://lore.kernel.org/r/20241126120322.1760862-1-s-vadapalli@ti.com
|
|
There are only two callers of "dwc3_generic_probe()", namely:
1. dwc3_generic_peripheral_probe()
2. dwc3_generic_host_probe()
Currently, the "mode" is set based on the device-tree node of the
platform device. Also, the DWC3 core doesn't support updating the "mode"
dynamically at runtime if it is set to "OTG", i.e. "OTG" is treated as a
separate mode in itself, rather than being treated as a mode which should
eventually lead to "host"/"peripheral".
Given that the callers of "dwc3_generic_probe()" clarify the expected
"mode" of the USB Controller, use that "mode" instead of the one
specified in the device-tree. This shall allow the USB Controller to
function both as a "Host" and as a "Peripheral" when the "mode" is "otg"
in the device-tree, based on the caller of "dwc3_generic_probe()".
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
|
|
Sometimes clocks provided to a consumer might not have .set_rate
operation (like gate or mux clocks), but have CLK_SET_PARENT_RATE flag
set. In that case it's usually possible to find a parent up the tree
which is capable of setting the rate (div, pll, etc). Implement a simple
lookup procedure for such cases, to traverse the clock tree until
.set_rate capable parent is found, and use that parent to actually
change the rate. The search will stop once the first .set_rate capable
clock is found, which is usually enough to handle most cases.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
|
|
Prepare v2025.01-rc4
|
|
In rzg2l_pinconf_set(), there are no new variables defined in the case
statement for PIN_CONFIG_INPUT_ENABLE so no additional scope is needed.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
|
On the RZ/G2L SoC family, the direction of the Ethernet TXC/TX_CLK
signal is selectable to support an Ethernet PHY operating in either MII
or RGMII mode. By default, the signal is configured as an input and MII
mode is supported. The ETH_MODE register can be modified to configure
this signal as an output to support RGMII mode.
As this signal is be default an input, and can optionally be switched to
an output, it maps neatly onto an `output-enable` property in the device
tree.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
|
The Ethenet interfaces on the Renesas RZ/G2L SoC family can operate at
multiple power supply voltages: 3.3V (default value), 2.5V and 1.8V.
rzg2l_pinconf_set() is extended to support the 2.5V setting, with a
check to ensure this is only used on Ethernet interfaces as it is not
supported on the SD & QSPI interfaces.
While we're modifying rzg2l_pinconf_set(), drop the unnecessary default
value for pwr_reg as it is set in every branch of the following if
condition.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
|
We can call dev_read_u32_default() instead of calling fdt_getprop() then
fdt32_to_cpu().
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
|
In the RZ/G2L family, core clocks are always on and can't be disabled.
However, drivers which are shared with other SoCs may call clk_enable()
or clk_enable_bulk() for a clock referenced in the device tree which
happens to be a core clock on the RZ/G2L. To avoid the need for
conditionals in these drivers, simply ignore attempts to enable a core
clock.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
|
Reuse i.MX93 pinctrl driver for i.MX91, because i.MX91 follows same
design as i.MX93 in IOMUXC controller.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
iMX91 reuses iMX93 controller and PHY, but with lower speed,
so add new DDR rates for i.MX91.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Add new rates to integer and frac PLL to support iMX91
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
i.MX91 is a derived from i.MX93, and most clocks could be reused from
i.MX93. Also Update imx93-clock.h to sync with linux next.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
iMX91 is reduced part from iMX93 with part number: i.MX9131/11/01
It removed A55_1, M33, MIPI DSI, LVDS, etc.
i.MX9131:
- Support 2.4GT/s DDR and HWFFC at 1.2GT/s
i.MX9121:
- A55 at 800Mhz and DDR at 1600MTS, with low drive mode.
i.MX9111:
- Support 1.6GT/s DDR and HWFFC at 800MT/s
i.MX9101:
- Support 800Mhz ARM clock
- Support 1.6GT/s DDR and HWFFC at 800MT/s
- No parallel display, eQOS, flexcan
Updated Clock/Container/CPU and etc for i.MX91
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
have_dual_base is set to false, so the 8ulp_data will be put in BSS
section which conflicts with the area of u-boot.dtb which padded just
after u-boot-nodtb.bin. So move 8ulp_data to data section to avoid
its content being corrupted by dtb.
Fixes: 51cfa66f2c4 ("gpio: imx_rgpio2p: support one address")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Building qemu_arm64_defconfig with CONFIGS_DM_RTC=n and CONFIGS_RTC_PL031=y
leads to a build failure.
Adjust the vexpress64 configuration to avoid circular dependency.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
|
|
Manorit Chawdhry <m-chawdhry@ti.com> says:
It has done a re-write of the full driver and the commits aren't split
to keep the bisectability intact.
Boot Logs: https://gist.github.com/manorit2001/1eaba109d722715a233244da693133d3
Link: https://lore.kernel.org/r/20241121-b4-upstream-pll-fix-v1-0-904f618897a7@ti.com
|
|
Based on the recommendation from HW team make modifications to
the sequence for more robustness.
- Unlock the PLL registers
- Enable external bypass
- Disable the PLL
- Program pllm and pllf
- Program Ref divider
- Enable other PLL controls like DSM_EN, DAC_EN,etc
- Enable calibration if available
- Enable PLL
- Wait for PLL lock and Calibration lock
- Remove external bypass
Re-write the full sequence from scratch as the previous sequence was way
off and keep it in a single commit for bisectability.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
|
|
base is more appropriate for the usage as the variable stores the base
address and seems more accurate w.r.t reg. Change reg to base.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
|
|
Those debug() calls might be useful, but beware. They can cause the DDR
controller to hang if we do not run the sequence quickly enough.
They usually are not an issue with upstream U-Boot and the default DDR
config, but they have become troublesome with custom DDR configs.
Drop those debug() statements that shouldn't be present in
time-sensitive code, to avoid anyone else falling into the trap.
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
|
|
implementation"
Christian Marangi <ansuelsmth@gmail.com> says:
This series is split in 2 part.
While adapting the LED boot and activity code to the new property
accepted by Rob in dt-schema repository, a big BUG was discovered.
The reason wasn't clear at start and took me some days to figure it
out.
This was triggered by adding a new phandle in the test.dts to
introduce test for the new OPs.
This single addition caused the sandbox CI test to fail in the
dm_test_ofnode_phandle_ot test.
This doesn't make sense as reverting the change made the CI test
to correctly finish. Also moving the uboot node down
after the first phandle (in test.dts the gpio one) also made
the CI test to correctly finish.
A little bit of searching and debugging made me realize the
parse phandle OPs didn't support other.dts at all and they
were still referencing phandle index from test.dts.
(more info in the related commit)
In short the test was broken all along and was working by
pure luck. The first 4 patch address and fix the problem for good.
The other 4 patch expand and address the property change for
LED boot/activity.
Posting in a single series as changes are trivial and just
to speedup review process. (and also because the second
part depends on the first)
All CI tested with azure pipeline.
Link: https://lore.kernel.org/r/20241110115054.2555-1-ansuelsmth@gmail.com
|
|
Update LED boot/activity to reference by phandle instead of label and
add to period property the "-ms" suffix.
This is a followup request by dt-schema maintainers that required LED
node to be referenced by a phandle to the node instead of indirectly by
the LED label and for timevalue to have a suffix.
While at it generalize the LED node label parsing since the logic is
common for generic LED bind and LED activity/boot.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
|
|
Implement ofnode_options phandle helper to get an ofnode from a phandle
option in /options/u-boot.
This helper can be useful since new DT yaml usually require to link a
phandle of a node instead of referencing it by name or other indirect
way.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Implement ofnode/tree_parse_phandle() helper as an equivalent of
of_parse_phandle to handle simple single value phandle.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Implement oftree variant of parse_phandle OPs.
There is currently a very hidden and laten BUG with parse_phandle OPs
that doesn't permit the support of multiple DTS in a system. One usage
example if sandbox with the usage of other.dts
The BUG is only present on live scenario where of_... OPs are used and
it's not present when fdt... OPs are used.
This is caused by an assumption made in __of_parse_phandle_with_args,
with the of_find_node_by_phandle call that pass the first arg as NULL.
This makes of_find_node_by_phandle use the default root node of the
system and doesn't permit the usage of alternative tree. This is correct
for normal system and also for the linux kernel where it's assumed a
single device tree.
It's problematic if other device tree needs to be used.
To fix this, introduce __of_root_parse_phandle_with_args to define a
root device tree for of_find_node_by_phandle.
Introduce all the variant OPs for this and in ofnode, the oftree OPs
following how it's done for other OPs with similar task.
For FDT scenario, ofnode_from_fdtdec_phandle_args is reworked to accept
a new variable, node and noffset_to_ofnode is used instead of
offset_to_ofnode. This is required to support multiple FDB blob to
calculate the correct of_offset of the ofnode.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
To ease debugging, use dev_err() instead of dev_dbg() for
alerting when regulator has nonunique value.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
Replace some debug() by dev_dbg() when dev variable
is available/valid.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
Aniket Limaye <a-limaye@ti.com> says:
This series adds OPP_LOW spec data in k3_avs driver and enables a config
option to select the OPP_LOW performance point.
J7200 SOC supports OPP_LOW and OPP_NOM as two Operating Performance
Points as per (7.5 Operating Performance Points) section in the
Datasheet [0].
- A72SS/MSMC at 2 GHz/1GHz operation must use OPP_NOM.
- A72SS/MSMC at 1 GHz/500 MHz operation can use OPP_NOM or OPP_LOW
voltage (though OPP_LOW voltage is recommended to reduce power
consumption).
The actual OPP voltage for the device is read from the efuse and
updated in k3_avs_probe().
The default j7200 devicetree and k3_avs driver set OPP_NOM spec
frequency and voltage.
In the board init file, if K3_OPP_LOW config is enabled, Check if
OPP_LOW AVS voltage read from efuse is valid and update frequency (A72
and MSMC) and voltage (VDD_CPU) as per the OPP_LOW spec.
[0]: https://www.ti.com/lit/gpn/dra821u (J7200 Datasheet)
Test logs:
https://gist.github.com/aniket-l/328ad93ed60c2419ed7be9f85e6b6075
- With series applied on master and CONFIG_K3_OPP_LOW enabled in
j7200_evm_r5_defconfig
- Logs shown with and without efuse register programmed for OPP_0
(Errors out if OPP_0 not found, programs OPP_LOW spec if found)
- Voltage update verified using 'i2c md 0x4c 0xe' in u-boot
- Frequency update verified using 'k3conf clock dump' in linux
Link: https://lore.kernel.org/r/20241119003617.1871183-1-a-limaye@ti.com
|
|
k3_avs driver checks opp_ids when probing and overwrites the voltage
values in vd_data for the respective board. The new k3_avs_check_opp()
can be called from board files to check the efuse data and returns 0 if
valid.
Also add the same check in k3_avs_program_voltage() to error out if
the efuse data was not valid.
Signed-off-by: Reid Tonking <reidt@ti.com>
Signed-off-by: Aniket Limaye <a-limaye@ti.com>
Reviewed-by: Manorit Chawdhry <m-chawdhry@ti.com>
|
|
J7200 SOC supports OPP_LOW and OPP_NOM as two Operating Performance
Points as per (7.5 Operating Performance Points) section in the
Datasheet [0].
- A72SS/MSMC at 2 GHz/1GHz operation must use OPP_NOM.
- A72SS/MSMC at 1 GHz/500 MHz operation can use OPP_NOM or OPP_LOW
voltage (though OPP_LOW voltage is recommended to reduce power
consumption).
Add OPP_LOW frequency->voltage entry to vd_data.
The actual OPP voltage for the device is read from the efuse and
updated in k3_avs_probe().
OPP_NOM corresponds to OPP_1 and OPP_LOW to OPP_0 efuse register
fields, as described in the Datasheet [0]
The register offsets and fields are described in the TRM (5.2.6.1.5
WKUP_VTM_VD_OPPVID_j Register) [1].
[0]: https://www.ti.com/lit/gpn/dra821u (J7200 Datasheet)
[1]: https://www.ti.com/lit/pdf/spruiu1 (J7200 TRM)
Signed-off-by: Reid Tonking <reidt@ti.com>
Signed-off-by: Aniket Limaye <a-limaye@ti.com>
|
|
not implmentated
Currently in _dm_gpio_set_flags() when set_flags ops is not implemented
direction_output()/_input() is used, but pull up/down is not supported by
these ops.
Signed-off-by: Zixun LI <admin@hifiphile.com>
|
|
Avoid crashing U-Boot when the GPIO controller for a button is disabled
or failed to probe. We also need to check the priv data for each button
since even if a button fails to probe it will still be polled by the
core code.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
The ST M24256E behaves as a regular M24C256, except for the E variant
which uses up another I2C address for Additional Write lockable page.
This page is 64 Bytes long and can contain additional data. Add entry
for it, so users can describe that page in DT. Note that users still
have to describe the main M24C256 area separately as that is on separate
I2C address from this page.
Unlike M24C32-D and M24C64-D, this part is specifically ST and does not
have any comparable M24* counterparts from other vendors, hence the st,
vendor prefix. Furthermore, the part name is M24256E without C between
the 24 and 256, this is not a typo. Finally, there is M24C256-D part,
which does contain 32 Bytes long Additional Write lockable page, which
is a different part and not supported by this patch.
Datasheet: https://www.st.com/resource/en/datasheet/m24256e-f.pdf
From Linux kernel commit:
339cb28b9ee6 ("eeprom: at24: add ST M24256E Additional Write lockable page support")
Signed-off-by: Marek Vasut <marex@denx.de>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
AMD/Xilinx changes for v2025.04-rc1
binman:
- Separate binman description from main DT
zynqmp:
- Enable binman for ZynqMP platforms
- DT sync with Linux v6.12
- Update usb5744 hub for SOMs
common:
- Drop SPL_FIT_GENERATOR support
versal2
- Enable OPTEE layers
ospi:
- Refactor the flash reset functionality
pytest:
- Fix tcminit mode handling
|
|
|
|
Tom Rini <trini@konsulko.com> says:
Hey all,
This is picking up Simon's v5 of the above-named series and making a few
more changes so that the follow-up series I have leads to arm64 being
supported for almost all jobs. To quote Simon's cover letter:
All gitlab runners are currently amd64 machines. This series attempts to
create a docker image which can also support arm64 so that sandbox tests
can be run on it.
The TARGET_... environment variables for grub could perhaps be adjusted,
using the new variables, but I have not done that for now.
Adding to what Simon said, we now build grub for all architectures as
the reason to install it was to be able to use the binaries in QEMU.
That won't provide us with amd64 binaries on arm64 hosts so we can't use
that shortcut anymore.
Link: https://lore.kernel.org/r/20241127172247.1488685-1-trini@konsulko.com
|
|
The cache-flush function is incorrect which causes a crash in the
remoteproc tests with arm64.
Fix both problems by using map_sysmem() to convert an address to a
pointer and map_to_sysmem() to convert a pointer to an address.
Also update the image-loader's cache-flushing logic.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: 3286d223fd7 ("sandbox: implement invalidate_icache_all()")
Acked-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Changes in v6:
- Re-introduce
Changes in v2:
- Drop message about EFI_LOADER
arch/sandbox/cpu/cache.c | 8 +++++++-
drivers/remoteproc/rproc-elf-loader.c | 18 +++++++++++-------
lib/efi_loader/efi_image_loader.c | 3 ++-
3 files changed, 20 insertions(+), 9 deletions(-)
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
This breaks chromebook_coral which says:
Video: No video mode configured in FSP!
This reverts commit 2e9313179a846b581c0fc3f6a49e19f3d343efa8.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
As the flash reset is handled in spi nor core, removing the
flash reset functionality. As the configuration like tristate
and hysterisis need to be enabled by the cdo. Handle the flash
reset only for mini u-boot case.
Rename the "cadence_qspi_versal_flash_reset" to generic name
"cadence_qspi_flash_reset" as this can be used by other platforms
as well.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20241108063537.13180-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
|
|
Always probing pmecc in the generic nand controller probe function and
bailing out if pmecc is missing, prevents the driver to be usable for
SoCs which do not have a pmecc hardware ecc engine like older sam9 SoCs,
for example at91sam9g20. Tested on sam9x60 that the call, which the
comment was moved to, is sufficient to probe the pmecc.
Signed-off-by: Alexander Dahl <ada@thorsis.com>
|
|
Add ops get_dir_flags() to read status from GPIO registers.
Signed-off-by: Zixun LI <admin@hifiphile.com>
|
|
Support GPIO configuration with following flags:
- in, out, out_active
- open_drain, pull_up
Signed-off-by: Zixun LI <admin@hifiphile.com>
|
|
This patch adds support for determining whether a gpio pin is mapped as
peripheral function.
Signed-off-by: Zixun LI <admin@hifiphile.com>
|
