| Age | Commit message (Collapse) | Author |
|---|
|
SARADC v1 and v2 have a different way of reading data, therefore let's
abstract this function so that it can be provided from the udevice.data
pointer.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
|
|
The registers are entirely different between SARADC v1 and SARADC v2, so
let's prepare to add another struct for accessing v2 registers by adding
a union.
Cc: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
|
|
This adds support for RK806, only the SPI variant has been tested.
The communication "protocol" over SPI is the following:
- write three bytes:
- 1 byte: [0:3] length of the payload, [6] Enable CRC, [7] Write
- 1 byte: LSB register address
- 1 byte: MSB register address
- write/read length of payload
The CRC is always disabled for now.
The RK806 technically supports I2C as well, and this should be able to
support it without any change, but it wasn't tested.
The DT node name prefix for the buck converters has changed in the
Device Tree and is now dcdc-reg. The logic for buck converters is
however manageable within the current logic inside the rk8xx regulator
driver. The same cannot be said for the NLDO and PLDO.
Because pmic_bind_children() parses the DT nodes and extracts the LDO
index from the DT node name, NLDO and PLDO will have overlapping
indices. Therefore, we need a separate logic from the already-existing
ldo callbacks. Let's reuse as much as possible though.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
|
|
By passing a rk8xx_reg_info directly to the internal get_value, it'd be
possible to call this same function with a logic for getting the
rk8xx_reg_info different from the current get_ldo_reg, e.g. for NLDO and
PLDO support for RK806.
No logic change is expected.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
|
|
On RK809 in PMIC_POWER_ENX registers, in order to set or clear a bit N,
the bit at offset N + 4 needs to be set otherwise nothing is done.
This fixes the inability to modify the SWITCH state on RK809.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: William Wu <william.wu@rock-chips.com>
[reworded commit log]
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
|
|
Those two functions had their last user removed in commit f9c68a566c4d
("rockchip: phycore_rk3288: remove phycore_init() function") part of
v2023.01 release, so let's do some cleanup here.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
|
|
The read-only mode is currently supported but only for 16b-aligned
buffers. For unaligned buffers, the last byte will be read in RW mode
right now, which isn't what is desired. Instead, let's put the
controller back into RO mode for that last byte and skip any write in
the xfer loop.
This is required for 3-wire SPI mode where PICO/POCI lanes are shorted
on HW level. This incidentally the recommended design for RK806 PMIC for
RK3588 products.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
|
|
Port the RK3399 part of the Rockchip IO-domain driver from linux.
This differs from linux version in that pmu io iodomain bit is enabled
in the write ops instead of in an init ops as in linux, this way we can
avoid keeping a full state of all supply that have been configured.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
RK3036 is using the USB product id normally used by RK3066B, and RK3328
is using the product id normally used by RK3368.
Fix this and update the default USB_GADGET_PRODUCT_NUM Kconfig option
for remaining supported Rockchip SoCs to match the product id used in
Maskrom mode.
Also remove a reference to an undefined ROCKCHIP_RK3229 Kconfig symbol.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
|
|
The USB2PHY regs already contain working default reset values for RK3328
and RK35xx as evidenced by the fact that this driver never has changed a
single value for these SoCs.
Reduce to only configure utmi_suspend_n and utmi_sel bits similar to
what is currently done on RK3399. Also add missing clkout_ctl for RK3588.
When enabled utmi_suspend_n is changed to normal mode and utmi_sel to
use otg/host controller utmi interface to phy. When disabled
utmi_suspend_n is changed to suspend mode and utmi_sel to use GRF utmi
interface to phy.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
|
|
On RK3399 the USB2PHY regs are located in the common GRF, remaining SoCs
that is supported by this driver have the USB2PHY regs in a different
GRF.
When support for RK356x, RK3588 and RK3328 was added this driver was
never updated to use correct GRF and have instead incorrectly written
to wrong GRF for these SoCs.
The default reset values for the USB2PHY have made USB mostly working
even when wrong GRF was used, however, following have been observed:
scanning bus usb@fd840000 for devices...
ERROR: USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did
not provide a handshake (OUT) (5)
ERROR: USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did
not provide a handshake (OUT) (5)
unable to get device descriptor (error=-1)
Fix this by using a regmap from rockchip,usbgrf prop and fall back to
getting a regmap for parent udevice instead of always getting the
common GRF.
Also protect against accidental clear of bit 0 in a reg with offset 0,
only bind driver to enabled otg/host-ports and remove unused headers.
Fixes: 3da15f0b49a2 ("phy: rockchip-inno-usb2: Add USB2 PHY for rk3568")
Fixes: cdf9010f6e17 ("phy: rockchip-inno-usb2: add initial support for rk3588 PHY")
Fixes: 9aa93d84038b ("phy: rockchip-inno-usb2: Add USB2 PHY for RK3328")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Replace the rockchip,cryptov1-rng compatible with compatibles used in
the linux device tree for RK3288, RK3328 and RK3399 to ease sync of SoC
device tree from linux.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
The U-Boot driver try to base the gpio bank id on the gpio-ranges prop
and fall back to base the bank id on the node name. However, the linux
driver try to base the bank id on the gpio alias id and fall back on
node order.
This can cause issues when SoC DT is synced from linux and gpioX@ nodes
has been renamed to gpio@ and gpio-ranges or a SoC specific alias has
not been assigned.
Try to use the gpio alias id as first fallback when a gpio-ranges prop
is missing to ease sync of updated SoC DT. Keep the current fallback on
node name as a third fallback to not affect any existing unsynced DT.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
The different macros use writel which is defined in asm/io.h, so let's
include the header so users of hardware.h do not need to include
asm/io.h as well.
While at it, remove asm/io.h includes wherever
asm/arch-rockchip/hardware.h is included already.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
|
|
hardware.h is only defining macros which are "wrappers" around writel().
writel() is however not available in hardware.h, <asm/io.h> needs to be
included. This means in order to use the wrappers in hardware.h, one
also needs to include the <asm/io.h> header.
However, this cannot be done currently because hardware.h is included in
include/configs files, which are implicitly included by every code file
by default, which makes the compilation of arch/arm/cpu/armv8/u-boot.lds
fail because ALIGN (the ARM assembly directive) got redefined by some
of the include files coming from <asm.io.h>.
Because nothing in the include/configs file actually use hardware.h,
let's remove the inclusion of hardware.h from the include/configs files
and explicitly add it wherever it is required.
This prepares for the next commit where <asm/io.h> will be included in
hardware.h.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
|
|
Prepare v2024.04-rc4
|
|
- Singular quirk DT property rename.
|
|
In case the PHY is fully described in DT, use PHY MDIO address
from DT directly instead of always using auto-detection. This
also fixes the behavior of 'mdio list' in such DT setup, which
now prints the PHY connected to the MAC correctly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
|
|
It is found that when DM is enabled, only generic init function is
called in .probe(). Baudrate is never honored. Add a function call
to .setbrg() when probing so that we can update the baudrate of the
serial device.
Signed-off-by: Yang Xiwen <forbidden405@outlook.com>
|
|
Add a new Kconfig symbol MDIO_TI_CPSW for the CPSW MDIO
driver and build it with proper DM support if enabled.
If MDIO_TI_CPSW is not enabled then we continue to
behave like before.
Clean up MDIO custom handling in am65-cpsw and use
dm_eth_phy_connect() to get the PHY.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Tested-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
|
|
The functions virtio_pci_get_config() and virtio_pci_set_config() don't
take the offset into account when reading the config space. For example
this manifests when U-Boot tries to read the MAC address of the VirtIO
networking device. It reads 6 equa bytes instead of the proper addess.
Fix those functions by taking the offset in the config space into
account.
Fixes: 4135e10732a0 ("virtio: Add virtio over pci transport driver")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
|
|
Michał Barnaś <barnas@google.com> says:
Fix the driver to behave like the chip datasheet requires.
Improve wake up function to send low signal on SDA line for at least
60us as chip requires to wake up. Fix sleep function to move the chip
into sleep mode, not into idle mode. Remove unnecessary for loop,
which would never run for more than one iteration.
|
|
The ATSHA204A chip requires SDA line to go low for at least 60us to
wake up the chip. Previous implementation did not meet this requirement
due to the NAK received on bus and not sending the zeroes.
The function to ignore the NAK and send bytes regardless is not
supported in the u-boot making it impossible to wake up the chip
this way.
Instead, the bus speed, if needed, is set to lowest value and the
message is sent to the address 0x0. This way, the address of zero
makes the SDA line go low for about 80us, meeting the required time
to wake up the chip. The zero length packet is not sent by the i2c,
so the one byte is sent to the transfer function, but only the address
is sent anyway.
After sending the zero address, the bus speed is restored to the
previous value if it was slowed down to wake up the chip.
Signed-off-by: Michał Barnaś <barnas@google.com>
|
|
Fix the sleep function to issue the sleep command instead of idle one.
Signed-off-by: Michał Barnaś <barnas@google.com>
|
|
Some previous commit changed the continue statement to return,
making the for loop used to retry waking up the chip to always
return after one iteration. This commit removes the loop, cleaning
the code a little.
Signed-off-by: Michał Barnaś <barnas@google.com>
|
|
- net: mv88e6xxx: fix missing SMI address initialization (Marek)
- mvebu: turris_omnia: Enable networking via ethernet switch (Marek)
- mvebu: helios-4: add config fragment for spi booting et al (Josua)
- rng: Add Turris Mox rTWM RNG driver (Max)
|
|
One fix makes the reboot more robust on some older board, another one
stabilises the initial clock setup on the A10/A20.
Two patches make sure our DRAM init does not actually change the content
of the DRAM array, which allows to use DRAM for Linux' pstore
functionality.
We get SPI support for U-Boot proper for one more SoC, that patch was
lingering around for a while, and should not affect other SoCs, so I am
merging this now.
As an added bonus, we get the defconfig file for a new board, the DT was
already synced from the kernel tree.
The CI looked happy with changes, and I tested them on five different
boards with different SoCs.
|
|
A RNG driver for Armada 3720 boards running the Turris Mox rWTM firmware
from CZ.NIC in the secure processor.
Signed-off-by: Max Resch <resch.max@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
The mv88e6xxx driver does not currently initialize the smi_addr field, but
instead keeps the default zero value. This leads to driver being unusable
on devices where the switch is not on address zero of the mdio bus. Fix
this problem by reading the SMI address from device tree.
Signed-off-by: Marek Mojík <marek.mojik@nic.cz>
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
No device tree in U-Boot or linux use the wrong spelling used in code.
Use correct property name as defined in dwc3 bindings.
Fixes: 062790f46131 ("usb: xhci-dwc3: Add USB2 PHY configuration")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Marek Vasut <marex@denx.de>
|
|
ring_idx was not correctly assigned in case of tflow_id is zero.
Which leads to wrong pairing of DMA for drivers like OSPI.
Fixes: 4312a1dfca26 ("dma: ti: k3-udma: Use ring_idx to pair k3 nav rings")
Reviewed-by: Jai Luthra <j-luthra@ti.com>
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
|
|
In udma_probe() the return value of setup_resources() is stored in the
u32 "ch_count" member of "struct udma_dev", due to which any negative
return value which indicates an error is masked.
Fix this by storing the return value of setup_resources() in the already
declared integer variable "ret", followed by assigning it to the "ch_count"
member of "struct udma_dev" in case of no error.
While at it, change the "return ret" at the end of udma_probe() to a
"return 0", to explicitly indicate that probe was successful.
Fixes: a8837cf43839 ("dma: ti: k3-udma: Query DMA channels allocated from Resource Manager")
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
|
|
Add support for DMA in J784S4 SoC.
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Signed-off-by: Hari Nagalla <hnagalla@ti.com>
Signed-off-by: Apurva Nandan <a-nandan@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> # AM69-SK
|
|
Add clk and device data which can be used by respective drivers
to configure clocks and PSC.
Signed-off-by: Hari Nagalla <hnagalla@ti.com>
Signed-off-by: Apurva Nandan <a-nandan@ti.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> # AM69-SK
|
|
Add support for J784S4 SoC Identification.
Signed-off-by: Hari Nagalla <hnagalla@ti.com>
Signed-off-by: Apurva Nandan <a-nandan@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> # AM69-SK
|
|
Add J784S4 initialization files for initial SPL boot.
config SYS_K3_MCU_SCRATCHPAD_BASE default value is same
for J721E, J721S2, J784S4. So combined them into a single
default.
Signed-off-by: Hari Nagalla <hnagalla@ti.com>
[ add firewall configurations and change the R5 MCU scratchpad ]
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Signed-off-by: Dasnavis Sabiya <sabiya.d@ti.com>
Signed-off-by: Apurva Nandan <a-nandan@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> # AM69-SK
|
|
During address translation #address/size-cells props are expected to
apply to child nodes. However, devfdt_get_addr_index() incorrectly use
the parent offset of the udevice parent instead of getting the offset of
the node parent. This will work in most cases when there is only one
udevice tied to a node.
On e.g. an Orange Pi R1 Plus TLS board the dwc3-generic (parent) and
dwc3-generic-host (child) udevice is tied to the same node.
In that case both the offset and parent values end up being the same.
As a result, the #address/size-cells props intended for child nodes
incorrectly gets applied to the node itself resulting in wrong addr
being returned, 0x0 instead of 0xff600000.
The following can be seen on console:
dwc3-generic-host usb@ff600000: this is not a DesignWare USB3 DRD Core
dwc3-generic-host usb@ff600000: failed to initialize core
Fix this by using the offset of the parent node and not the offset to
the node the parent udevice is tied to.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
|
|
Pinconfig nodes normally bind recursively with PINCTRL_FULL and
PINCONF_RECURSIVE enabled. However, during U-Boot proper pre-relocation
any node marked with e.g. bootph-all will not bind unless its parent is
also marked for pre-reloc.
group1 {
pinconf1 {
bootph-all;
};
};
This cause the following warning message to be shown during U-Boot
proper pre-reloc stage on Rockchip devices, e.g on RK3568:
ns16550_serial serial@fe660000: pinctrl_select_state_full: uclass_get_device_by_phandle_id: err=-19
and on RK3328:
ns16550_serial serial@ff130000: pinctrl_select_state_full: uclass_get_device_by_phandle_id: err=-19
Check pinconfig nodes pre-reloc status recursively to fix this and to
make pinconfig_post_bind work same at both U-Boot proper pre-reloc and
at TPL/SPL stage.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
|
|
Because of commit bf947d2a4b15 ("imx6ul: synchronise device tree with
linux"), the compatible property of lcdif in imx6ul.dtsi went from
compatible = "fsl,imx6ul-lcdif", "fsl,imx28-lcdif";
to
compatible = "fsl,imx6ul-lcdif", "fsl,imx6sx-lcdif";
without updating the mxsfb driver to match that change.
Add "fsl,imx6sx-lcdif" as a compatible id to fix that.
Fixes: bf947d2a4b15 ("imx6ul: synchronise device tree with linux")
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
|
|
These SoCs have two SPI controllers that are quite similar to the SPI
on previous Allwinner SoCs. The main difference is that new SoCs
don't have a clock divider (SPI_CCR register) inside SPI IP.
Instead SPI sample mode should be configured depending on the input clock.
For now SPI input clock source selection is not supported by this driver,
and only HOSC@24MHz can be used as input clock. Therefore, according to
the, manual we could change the SPI sample mode from delay half
cycle(default) to normal.
This patch adds a quirk for this kind of SPI controllers
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com>
Tested-by: Sam Edwards <CFSworks@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
|
|
Marek Vasut <marek.vasut+renesas@mailbox.org> says:
Rename R-Mobile to Renesas all over the place because the chips are
made by Renesas, while only a subset of them is from the R-Mobile line.
|
|
Rename rmobile_is_gen3_mmc0() to rcar_is_gen3_mmc0() because
this particular function is specific to Renesas R-Car Gen3.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
|
|
Rename ARCH_RMOBILE to ARCH_RENESAS because all the chips are made
by Renesas, while only a subset of them is from the R-Mobile
line.
Use the following command to perform the rename:
"
$ git grep -l 'ARCH_RMOBILE' | xargs -I {} sed -i 's@ARCH_RMOBILE@ARCH_RENESAS@g' {}
"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
|
|
Rename rmobile.h to renesas.h because all the chips are made
by Renesas, while only a subset of them is from the R-Mobile
line.
Use the following command to perform the rename:
"
$ git grep -l 'include.*rmobile.h' | \
xargs -I {} sed -i '/include.*rmobile.h/ s@rmobile.h@renesas.h@g' {}
"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
|
|
Rename RMOBILE_CPU_TYPE_* to RENESAS_CPU_TYPE_* because all
the chips are made by Renesas, while only a subset of them is
from the R-Mobile line.
Use the following command to perform the rename:
"
$ git grep -l '\<RMOBILE_CPU_TYPE_[A-Z0-9]\+\>' | \
xargs -I {} sed -i 's@\<RMOBILE\(_CPU_TYPE_[A-Z0-9]\+\)\>@RENESAS\1@g' {}
"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
|
|
Rename rmobile_get_cpu_rev_*() to renesas_get_cpu_rev_*() because
all the chips are made by Renesas, while only a subset of them is
from the R-Mobile line.
Use the following command to perform the rename:
"
$ git grep -l '\<rmobile_get_cpu_rev_\(integer\|fraction\)\>' | \
xargs -I {} sed -i 's@\<rmobile_get_cpu_rev_\(integer\|fraction\)\>@renesas_get_cpu_rev_\1@g' {}
"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
|
|
Rename rmobile_get_cpu_type() to renesas_get_cpu_type() because
all the chips are made by Renesas, while only a subset of them
is from the R-Mobile line.
Use the following command to perform the rename:
"
$ git grep -l '\<rmobile_get_cpu_type\>' | \
xargs -I {} sed -i 's@\<rmobile_get_cpu_type\>@renesas_get_cpu_type@g' {}
"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
|
|
FDT functions is not working when OF_LIVE is enabled.
Convert fdt parsing functions to ofnode parsing functions
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com>
|
|
Usage of common.h is deprecated.
* Remove common.h from RNG drivers.
* Sort includes.
* Add time.h to sandbox driver.
* Add linux/types.h to rng.h to provide size_t.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
|
|
The actual driver does not work when there is no linked PHY. These
changes add support for fixed-link feature in the device tree.
Signed-off-by: BELOUARGA Mohamed <m.belouarga@technologyandstrategy.com>
|
