| Age | Commit message (Collapse) | Author |
|---|
|
Import linux commit 007773e16a6f ("spi: nxp-fspi: Ensure width is
respected in spi-mem operations") to fix SPI access on boards which
don't have all SPI I/O lines connected to the flash.
Since commit 71025f013ccb ("mtd: spi-nor-core: Rework hwcaps selection")
u-boot figures out the capabilities by looking at spi_mem_supports_op().
The FlexSPI driver doesn't take the board layout into account. Fix that.
Fixes: 383fded70c4f ("spi: nxp_fspi: new driver for the FlexSPI controller")
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
Add the support of the BSEC clock used by the STM32MP misc driver
since the commit 622c956cada0 ("stm32mp: bsec: manage clock when present
in device tree") even if this clock is not yet defined in kernel device
tree stm32mp151.dtsi.
This patch avoids issue for basic boot when this secure clock are not
provided by secure world with SCMI.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
https://source.denx.de/u-boot/custodians/u-boot-rockchip
- Add Rockchip SFC driver support;
- DTS sync from kernel;
- emmc hs400 support for rk3399;
- Fix for spinore bootdevice and MMC boot order;
|
|
Make px30 SFC clock configurable
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Adds support for XT25F128B used on Odroid Go Advance. Unfortunately
this chip uses a continuation code which I cannot seem to parse, so
there are possibly going to be collisions with chips that use the same
manufacturer/ID.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
This patch adds support for the Rockchip serial flash controller
found on the PX30 SoC. It should work for versions 3-5 of the SFC
IP, however I am only able to test it on v3.
This is adapted from the WIP SPI-MEM driver for the SFC on mainline
Linux. Note that the main difference between this and earlier versions
of the driver is that this one does not support DMA. In testing
the performance difference (performing a dual mode read on a 128Mb
chip) is negligible. DMA, if used, must also be disabled in SPL
mode when using A-TF anyway.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
- Some CFI flash related fixups (Kconfig & header) (Bin)
- Enable CFI flash support on the QEMU RISC-V virt machine. (Bin)
|
|
This patch adds support for the RK3568 platform to this driver.
Signed-off-by: Yifeng Zhao <yifeng.zhao@rock-chips.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Add clock, phy and other configuration, it is convenient to support
new controller. Here a short summary of the changes:
- Add mmc_of_parse to parse dts config.
- Remove OF_PLATDATA related code.
- Reorder header inclusion.
- Add phy ops.
- add ops set_ios_post to modify the parameters of phy when the
clock changes.
- Add execute tuning api for hs200 tuning.
Signed-off-by: Yifeng Zhao <yifeng.zhao@rock-chips.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
The DM version CFI flash driver is in driver/mtd/cfi_flash.c, which
only gets built when FLASH_CFI_DRIVER is on. If CFI_FLASH is on but
FLASH_CFI_DRIVER is not, nothing is enabled at all.
Fix this dependency by selecting FLASH_CFI_DRIVER when CFI_FLASH is
enabled.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
Returning fabricated CRS value (0xFFFF0001) by PCIe Root Complex to OS is
allowed only for 4-byte PCI_VENDOR_ID config read request and only when
CRSSVE bit in Root Port PCIe device is enabled. In all other error PCIe
Root Complex must return all-ones.
So implement this logic in pci-aardvark.c driver properly.
aardvark HW does not have Root Port PCIe device and U-Boot does not
implement emulation of this device. So expect that CRSSVE bit is set as
U-Boot can already handle CRS value for PCI_VENDOR_ID config read request.
More callers of pci_bus_read_config() function in U-Boot do not check for
return value, but check readback value. Therefore always fill readback
value in pcie_advk_read_config() function. On error fill all-ones of
correct size as it is required for PCIe Root Complex.
And also correctly propagates error from failed config write request to
return value of pcie_advk_write_config() function. Most U-Boot callers
ignores this return value, but it is a good idea to return correct value
from function.
These issues about return value of failed config read requests, including
special handling of CRS were reported by Lorenzo and Bjorn for Linux kernel
driver pci-aardvark together with quotes from PCIe r4.0 spec, see details:
https://lore.kernel.org/linux-pci/20210624213345.3617-1-pali@kernel.org/t/#u
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
During cold start, with some HDDs, mv_sata_identify() does not populate
the ID words on the 1st ATA ID command. In fact, the first ATA ID
command will only power up the drive, and then the ATA ID command
processing is lost in the process.
Tests with:
- Seagate ST9250320AS 250GB HDD and Seagate ST4000DM004-2CV104 4TB HDD.
- Zyxel NSA310S (Kirkwood 88F6702), Marvell Dreamplug (Kirkwood 88F6281),
Seagate GoFlex Home (Kirkwood 88F6281), Pogoplug V4 (Kirkwood 88F6192).
Observation:
- The Seagate ST9250320AS 250GB took about 3 seconds to spin up.
- The Seagate ST4000DM004-2CV104 4TB took about 8 seconds to spin up.
- mv_sata_identify() did not populate the ID words after the call to
mv_ata_exec_ata_cmd_nondma().
- Attempt to insert a long delay of 30 seconds, ie. mdelay(30_000), after
the call to ata_wait_register() inside mv_ata_exec_ata_cmd_nondma() did
not help with the 4TB drive. The ID words were still empty after that 30s
delay.
Patch Description:
- Added a second ATA ID command in mv_sata_identify(), which will be
executed if the 1st ATA ID command did not return with valid ID words.
- Use the HDD drive capacity in the ID words as a successful indicator of
ATA ID command.
- In the scenario where a box is rebooted, the 1st ATA ID command is always
successful, so there is no extra time wasted.
- In the scenario where a box is cold started, the 1st ATA command is the
power up command. The 2nd ATA ID command alleviates the uncertainty of
how long we have to wait for the ID words to be populated by the SATA
controller.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
|
|
https://source.denx.de/u-boot/custodians/u-boot-imx
u-boot-imx-20210809
- new SOC: add support for imx8ulp
- Toradex fixes for colibri (vf / imx6 / imx7 / imx8x)
- convert to DM for mx28evk
- Fixes for Gateworks ventana boards
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/8639
|
|
Add iMX8ULP DDR initialization driver which loads the DDR timing
parameters and executes the training procedure.
When enabling IMX8ULP_DRAM_PHY_PLL_BYPASS, using PHY PLL bypass mode
to do DDR init
Signed-off-by: Ye Li <ye.li@nxp.com>
|
|
Move struct mu_type to common header to make it reusable by upower and
S400
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
This driver uses FSB to read some fuses, but not support program fuse.
It only works in SPL (secure mode), u-boot needs traps to ATF to
read them.
Some fuses can read from S400 API and others are from FSB.
Also support program some fuses via S400 API
Signed-off-by: Ye Li <ye.li@nxp.com>
|
|
Since S400 will set the memory of SPL image to R/X. We can't write
to any data in SPL image.
1. Set the parameters save/restore only for u-boot, not for SPL. to
avoid write data.
2. Not use MU DM driver but directly call MU API to send release XRDC
to S400 at early phase.
3. Configure the SPL image memory of SRAM2 to writable (R/W/X)
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Add API to support fuse read and write
Signed-off-by: Ye Li <ye.li@nxp.com>
|
|
The RDC API is updated to add a field for XRDC or TRDC
Signed-off-by: Ye Li <ye.li@nxp.com>
|
|
Add S400 API for image authentication
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
According to latest S400 API doc, the the success indicate value is
changed to 0xd6. So update the driver codes.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
i.MX8ULP reuse same SDHC IP as i.MX8M, so follow i.MX8M code logic.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Add pinctrl driver for i.MX8ULP
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Support i.MX8ULP in fec_mxc
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
|
|
Add MU driver and S400 API. Need enable MISC driver to work
Signed-off-by: Ye Li <ye.li@nxp.com>
|
|
At present it is possible to call uclass_get() before driver model is
inited. In fact this happens on x86 boards which use Intel FSPv1, since
mrccache_get_region() tries to get the SPI flash device very early
during init.
This has always been undefined behaviour. Previously it generally worked,
i.e. returned an error code without crashing, because gd->uclass_root_s
is zeroed and the uclass can be added despite driver model not being
ready, due to the way lists are implemented. With the change to use a
gd->uclass_root pointer, this no-longer works. For example, it causes a
hang on minnowmax.
Fix this by adding a check that driver model is ready when uclass_get() is
called. This function is called in the process of locating any device, so
it is a good place to add the check.
This fixes booting on minnowmax.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: 8a715530bb1 ("dm: core: Allow the uclass list to move")
|
|
Migrate the dm_warn function to log macro with
LOGC_DM category and LOGL_WARNING level.
This macro allows filtering with log command and allows
output on all log backend.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
https://source.denx.de/u-boot/custodians/u-boot-video
- add display driver for ST-Ericsson MCDE
- drop legacy CONFIG_VIDEO dependency for Hitachi tx18d42vm
|
|
This is not used in U-Boot at present. Drop it and related config options.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
We don't need these checks anymore since when PCI is enabled, driver model
is always used.
Drop them.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
set_delay() has return type as void. If there are any errors while
setting tapdelay's it won't be able to return them.
Change the prototype of set_delay() in sdhci_ops structure and return
the errors from wherever it is called.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Change return type of arasan_sdhci_set_tapdelay() to int, to facilitate
returning errors. Get return values from input and output set clock phase
functions inside arasan_sdhci_set_tapdelay() and return those errors.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Add firmware based reset controller for Xilinx ZynqMP SoC to let other
drivers to call reset functions. Driver is only tested on Xilinx ZynqMP but
support for Xilinx Versal can be simply added. That's why reset_id and
nr_reset are assigned in probe folder.
Driver is inpired by driver from Linux kernel.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
The whole driver logic is taken from Linux kernel but only set/get/reset
functions are implemented. When device is power off RTC is power out of
battery.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
RTCs are using aliases for sequences. That's why enable
DM_UC_FLAG_SEQ_ALIAS for exact RTC indentification.
The same flag is used by a lot of other uclasses like mmc, pci, serial,
spi, timer, tpm, etc.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
We don't need these checks anymore since when PCI is enabled, driver model
is always used.
Drop them.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
We don't need this check anymore since when PCI is enabled, driver model
is always used.
Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Now that DM_PCI is always enabled we don't need to check it. Drop this
old code.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Now that DM_PCI is always enabled we don't need to check it. Drop this
old code.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Now that DM_PCI is always enabled we don't need to check it. Drop this
old code.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Now that DM_PCI is always enabled, check on CONFIG_PCI instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Update for non-PCI users of this code, reword]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
We don't need this check anymore since when PCI is enabled, driver model
is always used.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
We don't need this check anymore since when PCI is enabled, driver model
is always used.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
- SPI-NOR fix (Big Meng)
- XMC XM25QH64C flash (Reto Schneider)
|
|
The DT bindings of "jedec,spi-nor" [1] defines "m25p,fast-read" property
to indicate that "fast read" opcode can be used to read data from the
chip instead of the usual "read" opcode.
If this property is not present in DT, mask out fast read in
spi_nor_init_params(). This change mirrors the same logic in
spi_nor_info_init_params() in drivers/mtd/spi-nor/core.c in
the Linux kernel v5.14-rc3.
[1] Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml in the kernel tree
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
The smart spi_nor_adjust_hwcaps() does not respect the SPI flash's
hwcaps, and only looks to the controller on what can be supported.
The flash's hwcaps needs to be AND'ed before checking.
Fixes: 71025f013ccb ("mtd: spi-nor-core: Rework hwcaps selection")
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
When slave drivers don't set the max_read_size, the spi-mem should
directly use data.nbytes and not limit to any size. But current
logic will limit to the max_write_size.
This commit mirrors the same changes in the dm version done in
commit 535b1fdb8e5e ("spi: spi-mem: Fix read data size issue").
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
This chip has been (briefly) tested on the MediaTek MT7688 based GARDENA
smart gateway.
Datasheet: http://xmcwh.com/Uploads/2020-12-17/XM25QH64C_Ver1.1.pdf
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
- Fixed broken ICH SPI driver in software sequencer mode
- Added "m25p,fast-read" to SPI flash node for x86 boards
- Drop ROM_NEEDS_BLOBS and BUILD_ROM for x86 ROM builds
- Define a default TSC timer frequency for all x86 boards
- x86 MTRR MSR programming codes bug fixes
- x86 "hob" command bug fixes
- Don't program MTRR for DRAM for FSP1
- Move INIT_PHASE_END_FIRMWARE to FSP2
- Use external graphics card by default on Intel Crown Bay
- tangier: Fix DMA controller IRQ polarity in CSRT
|
|
It is a pain to have to specify the value 10 in each call. Add a new
dectoul() function and update the code to use it.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
