| Age | Commit message (Collapse) | Author |
|---|
|
This reverts commit d927d1a80843e1c3e2a3f0b8f6150790bef83da1, reversing
changes made to c07ad9520c6190070513016fdb495d4703a4a853.
These changes do not pass CI currently.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Emulate Secure World's FF-A ABIs and allow testing U-Boot FF-A support
Features of the sandbox FF-A support:
- Introduce an FF-A emulator
- Introduce an FF-A device driver for FF-A comms with emulated Secure World
- Provides test methods allowing to read the status of the inspected ABIs
The sandbox FF-A emulator supports only 64-bit direct messaging.
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Cc: Jens Wiklander <jens.wiklander@linaro.org>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
Provide armffa command showcasing the use of the U-Boot FF-A support
armffa is a command showcasing how to invoke FF-A operations.
This provides a guidance to the client developers on how to
call the FF-A bus interfaces. The command also allows to gather secure
partitions information and ping these partitions. The command is also
helpful in testing the communication with secure partitions.
For more details please refer to the command documentation [1].
[1]: doc/usage/cmd/armffa.rst
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Cc: Jens Wiklander <jens.wiklander@linaro.org>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
Add Arm FF-A support implementing Arm Firmware Framework for Armv8-A v1.0
The Firmware Framework for Arm A-profile processors (FF-A v1.0) [1]
describes interfaces (ABIs) that standardize communication
between the Secure World and Normal World leveraging TrustZone
technology.
This driver uses 64-bit registers as per SMCCCv1.2 spec and comes
on top of the SMCCC layer. The driver provides the FF-A ABIs needed for
querying the FF-A framework from the secure world.
The driver uses SMC32 calling convention which means using the first
32-bit data of the Xn registers.
All supported ABIs come with their 32-bit version except FFA_RXTX_MAP
which has 64-bit version supported.
Both 32-bit and 64-bit direct messaging are supported which allows both
32-bit and 64-bit clients to use the FF-A bus.
FF-A is a discoverable bus and similar to architecture features.
FF-A bus is discovered using ARM_SMCCC_FEATURES mechanism performed
by the PSCI driver.
Clients are able to probe then use the FF-A bus by calling the DM class
searching APIs (e.g: uclass_first_device).
The Secure World is considered as one entity to communicate with
using the FF-A bus. FF-A communication is handled by one device and
one instance (the bus). This FF-A driver takes care of all the
interactions between Normal world and Secure World.
The driver exports its operations to be used by upper layers.
Exported operations:
- ffa_partition_info_get
- ffa_sync_send_receive
- ffa_rxtx_unmap
Generic FF-A methods are implemented in the Uclass (arm-ffa-uclass.c).
Arm specific methods are implemented in the Arm driver (arm-ffa.c).
For more details please refer to the driver documentation [2].
[1]: https://developer.arm.com/documentation/den0077/latest/
[2]: doc/arch/arm64.ffa.rst
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Cc: Jens Wiklander <jens.wiklander@linaro.org>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
https://source.denx.de/u-boot/custodians/u-boot-at91
First set of u-boot-atmel fixes for the 2023.07 cycle:
This small fixes set includes the LTO configs for the boards that had
the SPL size up to the limit (sama5d2-based), such that more code can be
added. It also includes a fix for mmc non-removable.
|
|
If the device attached to the MMC bus is not removable, set force card-detect
bit to bypass card detection procedure, so card detection pin can be used for
other purposes.
It's also a workaround for SAMA5D2 who doesn't drive CMD if using GPIO for card
detection.
Signed-off-by: Zixun LI <zli@ogga.fr>
Reviewed-by: Eugen Hristev <eugen.hristev@collabora.com>
|
|
Modify the drivers to add of_xlate ops and transform clock id.
Signed-off-by: Xingyu Wu <xingyu.wu@starfivetech.com>
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
Reviewed-by: Torsten Duwe <duwe@suse.de>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
|
|
Drop the PLL part in SYSCRG driver and separate to be a single
PLL driver of which the compatible is "starfive,jh7110-pll".
Signed-off-by: Xingyu Wu <xingyu.wu@starfivetech.com>
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
Reviewed-by: Torsten Duwe <duwe@suse.de>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
|
|
This is required since user may want to either call the remove method
of video driver and reset the display or not call the remove method
to continue displaying until next stage.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
U-boot proper can use frame buffer address passed from SPL to reserve
the memory area used by framebuffer set in SPL so that splash image
set in SPL continues to get displayed while u-boot proper is running.
Put the framebuffer address and size in a bloblist to make them
available at u-boot proper, if in u-boot proper CONFIG_VIDEO is defined.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Add method to reserve video framebuffer information using blob,
received from previous stage.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
During LPDDR initialization we will loop through a series of frequency
changes in order to train at the various operating frequencies. During
this training, accessing the DRAM_CLASS bitfield could happen during a
frequency change and cause the read to hang.
Store the DRAM type into the main structure to avoid multiple readings
while the independent phy is training.
Signed-off-by: Bryan Brattlof <bb@ti.com>
|
|
For once this adds USB support for two SoCs: the H616 and the F1C100s
series. The rest is support for LPDDR3 DRAM chips on H616 boards.
Gitlab CI passed, and I booted that briefly on an H616 and an F1C200s
board. I don't have an H616 board with LPDDR3 DRAM, but reportedly that
works for Mikhail, and doesn't regress on my DDR3 boards.
|
|
https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2023.10-rc1 v2
axi_emac:
- Change return value if RX packet is not ready
cadence_qspi:
- Enable flash reset for Versal NET
dt:
- Various DT syncups with Linux kernel
- SOM - reserved pmufw memory location
fpga:
- Add load event
mtd:
- Add missing dependency for FLASH_CFI_MTD
spi/nand:
- Minor cleanup in Xilinx drivers
versal-net:
- Prioritize boot device in boot_targets
- Wire mini ospi/qspi/emmc configurations
watchdog:
- Use new versal-wwdt property
xilinx:
- fix sparse warnings in various places ps7_init*
- add missing headers
- consolidate code around zynqmp_mmio_read/write
- switch to amd.com email
zynqmp_clk:
- Add handling for gem rx/tsu clocks
zynq_gem:
- Configure mdio clock at run time
zynq:
- Enable fdt overlay support
zynq_sdhci:
- Call dll reset only for ZynqMP SOCs
|
|
This enables implementing custom logic after a bitstream was loaded
into the fpga.
Signed-off-by: Christian Taedcke <christian.taedcke@weidmueller.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Link: https://lore.kernel.org/r/20230720072724.11516-1-christian.taedcke-oss@weidmueller.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
|
|
Add gem_tsu and gem0_rx till gem3_rx to return proper register from
zynqmp_clk_get_register. Otherwise firmware won't be able to set clock
for these due to incorrect register address.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230720072859.3724-1-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
|
|
gem0_rx till gem3_rx and gem_tsu are missing from set rate function.
Add them, so that they can be set from pmu firmware via clock framework.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230719084912.30209-1-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
|
|
If there is no incoming package than axiemac_recv will return -1 which
in turn leads to printing `eth_rx: recv() returned error -1` error
message in eth_rx function. But missing a package is not an fatal error,
so return -EAGAIN in that case would be more suitable.
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com>
Link: https://lore.kernel.org/r/20230719065337.69280-1-bigunclemax@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
|
|
cfi_mtd requires add_mtd_device() which is available only when MTD is
enabled that's why record this dependency.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/76ae01ce2b2c988758b69e0f0cdcc21bf301c01e.1688472227.git.michal.simek@amd.com
|
|
Dll reset is needed only for ZynqMP platforms, add condition in tuning
to call arasan_zynqmp_dll_reset() just for ZynqMP platforms.
On other platforms like Versal NET, If this condition is not added, we
see PLM error messages when dll reset smc is called.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/d673ff3bdc5c236a7f0403c920e719684abd6059.1688991117.git.michal.simek@amd.com
|
|
Update my and DPs email address to match current setup.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/aba5b19b9c5a95608829e86ad5cc4671c940f1bb.1688992543.git.michal.simek@amd.com
|
|
zynqmp_mmio_read/write() are firmware provided hooks that's why use only
zynqmp_firmware.h for function declaration.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/e7489556f9e447c737a578c169d7e1e43586a273.1687524706.git.michal.simek@amd.com
|
|
Enable flash reset functionality for Versal NET platform.
In cadence_qspi.c there is weak function defined for reset, hence remove
the check for config, so that it will work for Versal and Versal NET
platforms.
Add register defines in Versal NET hardware.h for mini U-Boot flash
reset.
Add read_delay initialization for Versal NET also.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230614120452.21019-1-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
|
|
As per spec MDC must not exceed 2.5MHz, read the pclk clock
from the device tree and update the MDC clock divisor.
GEM devices support larger clock divisors and have a different
range of divisors. Program the MDIO clock divisors based on
the clock rate of the pclk clock.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20230619034922.24019-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
|
|
status and ecc_status are of unsigned type where they are compared for
negative value. This is pointed by below sparse warning. Change datatype
to int to fix this.
warning: comparison of unsigned expression in '< 0' is always false
[-Wtype-limits]
Signed-off-by: Algapally Santosh Sagar <santoshsagar.algapally@amd.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230614090359.10809-5-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
|
|
Add missing prototype to fix the sparse warning, warning: no
previous prototype for 'zynq_qspi_mem_exec_op' [-Wmissing-prototypes].
Signed-off-by: Algapally Santosh Sagar <santoshsagar.algapally@amd.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230614090359.10809-4-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
|
|
Add missing prototype to fix the below sparse warning
warning: no previous prototype for 'xilinx_qspi_mem_exec_op'
[-Wmissing-prototypes]
Signed-off-by: Algapally Santosh Sagar <santoshsagar.algapally@amd.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230614090359.10809-2-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
|
|
DT binding has been approved that's why use new compatible string.
The old one is mark as deprecated and should be removed after some
releases.
Link: https://lore.kernel.org/r/20230420104231.2243079-3-srinivas.neeli@amd.com/
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/6e78d0d2e21f2f9e7f8f448bb8e0d27ced4de7d3.1686655339.git.michal.simek@amd.com
|
|
Now that the Allwinner USB PHY driver supports the H616 quirk, let's
enable support for USB ports on that SoC.
We connect the compatible string to a new struct describing the SoCs USB
PHY properties, and unblock the PHY driver selection in Kconfig.
A later patch will enable USB support in the H616 boards' defconfigs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
|
|
The H616 USB PHY is some kind of special snowflake: Only port2 works out
of the box, but all other ports need some help from this port2 to work
correctly: The CLK_BUS_PHY2 and RST_USB_PHY2 clock and reset need to be
enabled, and the SIDDQ bit in the PMU PHY control register needs to be
cleared. For this register to be accessible, CLK_BUS_ECHI2 needs to be
ungated. Don't ask ....
Follow the respective Linux patch (b45c6d80325b) and add a quirk bit,
triggering the special sequence as outlined above, for PHYs other than
PHY2: ungate this one special clock, and clear the SIDDQ bit. We also
pick the clock and reset from PHY2 and enable them as well.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
|
|
So far we were assigning some crude "type" (SoC name, really) to each
Allwinner USB PHY model, then guarding certain quirks based on this.
This does not only look weird, but gets more or more cumbersome to
maintain.
Remove the bogus type names altogether, instead introduce flags for each
quirk, and explicitly check for them.
This improves readability, and simplifies future extensions.
Port of Linux patch 8dd256bae653.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
|
|
At the moment we use "select" in each Allwinner SoC's Kconfig section to
include the USB PHY driver in the build. This means it cannot be disabled
via Kconfig, although USB is not really a strictly required core
functionality, and a particular board might not even include USB ports.
Rework the Kconfig part by removing the "select" lines for each SoC's
section, and instead letting it default to "y" in the PHY driver section
itself. We use "depends on !" to exclude the few SoCs we don't support
(yet). The Allwinner V3s does not enable USB (PHY) support at the moment,
even though it should work: let the PHY default to "n" to keep the
current behaviour.
Also the MUSB USB driver directly calls some functions from the PHY
driver, so let the former depend on the PHY driver.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Tested-by: Sam Edwards <CFSworks@gmail.com>
|
|
The Allwinner F1C100s implements a single USB PHY, connected to its MUSB
OTG controller. The USB PHY is of the simpler, older type (like the A10),
the only real difference is that it's indeed only one PHY.
Add a struct describing those F1C100s USB PHY properties, and connect it
to the new compatible string.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
|
|
In its of_xlate() function, the Allwinner USB PHY driver compares the
args_count variable against the number of implemented USB PHYs, although
this is the *number of arguments* to the DT phandle property. Per the DT
binding for this PHY device, this number is always one, so this check
will always fail if the particular SoC implements exactly one USB PHY.
So far this affected only the V3s (which has USB support disabled), but
the F1C100s also sports one PHY only.
Fix that check to compare args_count against exactly 1, and the args[0]
content (requested PHY number) against the number of implemented PHYs.
This fixes USB operation on the Allwinner V3s and allows to enable USB
on the Allwinner F1C100s SoC.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
|
|
The behaviour of dev_read_addr_size() is surprising as it does not
handle #address-cells and #size-cells but instead hardcodes the values
based on sizeof(fdt_addr_t).
This is different from dev_read_addr_size_index() and
dev_read_addr_size_name() both of which do read the cell sizes from the
device tree.
Since dev_read_addr_size() is only used by a single driver and this
driver is broken when CONFIG_FDT_64BIT does not match the address size
in the device tree, fix the function to behave like all of the other
similarly named functions. Drop the property name argument as the only
caller passes "reg" and this is the expected property name matching the
other similarly named functions.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # chromebook_jerry
Tested-by: Simon Glass <sjg@chromium.org> # chromebook_bob
|
|
of_property_match_string calls of_find_property to search for the
string property.
If the device node does not exist, of_find_property returns NULL, and
of_property_match_string returns -EINVAL, which is correct.
However, if the device node exists, but the property is not found,
of_find_property still returns NULL, but it will place -FDT_ERR_NOTFOUND
in the *lenp variable.
of_property_match_string does not use the lenp parameter, thus this error
case is being lost, and treated as if the node is NULL, and returns
-EINVAL, which is incorrect.
The callers of of_property_match_string treat the error differently if
the return value is -EINVAL or -ENOENT, e.g. in dwc3 driver:
ret = generic_phy_get_by_name(dev, "usb3-phy", &phy);
if (!ret) {
ret = generic_phy_init(&phy);
if (ret)
return ret;
} else if (ret != -ENOENT && ret != -ENODATA) {
debug("could not get phy (err %d)\n", ret);
return ret;
} else {
phy.dev = NULL;
}
So the caller drivers will just consider the property missing if -ENOENT
is returned, versus the case of -EINVAL, which means something else.
To fix this situation, changed the code to call the of_find_property
with the right third argument to catch this error code and treat it
accordingly.
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
|
|
|
|
Set MMC clock when reverting to safe bus mode and speed
in case current MMC mode fails. Otherwise, trying out
the other modes may fail as well.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
[hp: fallback to legacy_speed]
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
|
|
When tuning command (CMD21) fails with command error, call
mmc_send_stop_transmission() to send stop command (CMD12).
Reviewed-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Add dev_dbg() message in case tuning abort fails
Move tuning opcode check from mmc_abort_tuning()]
Reviewed-by: Peng Fan <peng.fan@nxp.com>
|
|
If a tuning command times out, the card could still be processing it,
which will cause problems for recovery. The eMMC specification section
6.6 Data transfer mode (cont’d) claims that CMD12 can be used to stop
CMD21:
"
The relationship between the various data transfer modes is summarized (see Figure 27):
- All data read commands can be aborted any time by the stop command (CMD12).
The data transfer will terminate and the Device will return to the Transfer State.
The read commands are: ... send tuning block (CMD21) ....
"
Add a function that does that.
Based on Linux commit [1] and [2].
[1] e711f0309109 ("mmc: mmc: Introduce mmc_abort_tuning()")
[2] 21adc2e45f4e ("mmc: Improve function name when aborting a tuning
cmd")
Reviewed-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Update commit message, quote relevant part of the specification.
Rename to mmc_send_stop_transmission().
Remove tuning opcode check, this is controller driver specific.
Deduplicate part of mmc_read_blocks() using this function.]
Reviewed-by: Peng Fan <peng.fan@nxp.com>
|
|
For MMC/eMMC, the MMC_CMD_STOP_TRANSMISSION response is R1 for read
transfers and R1b for write transfers per JEDEC Standard No. 84-B51
Page 126 . The response is R1b unconditionally per Physical Layer
Simplified Specification Version 9.00.
Correct the response type and add a comment about it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
|
|
When CONFIG_CMD_MMC and CONFIG_MMC are disabled, still some compilation
errors are seen as below due to unresolved symbols.
drivers/dfu/dfu_mmc.o: in function `mmc_block_op':
drivers/dfu/dfu_mmc.c:32: undefined reference to `find_mmc_device'
drivers/dfu/dfu_mmc.c:54: undefined reference to `mmc_get_blk_desc'
drivers/dfu/dfu_mmc.c:67: undefined reference to `mmc_get_blk_desc'
drivers/dfu/dfu_mmc.c:70: undefined reference to `mmc_get_blk_desc'
drivers/dfu/dfu_mmc.o: in function `dfu_fill_entity_mmc':
drivers/dfu/dfu_mmc.c:369: undefined reference to `find_mmc_device'
drivers/dfu/dfu_mmc.c:376: undefined reference to `mmc_init'
drivers/dfu/dfu_mmc.c:403: undefined reference to `mmc_get_blk_desc'
gnu/aarch64/lin/aarch64-linux/bin/aarch64-linux-gnu-ld.bfd: line 4:
31661 Segmentation fault (core dumped) $CC --sysroot=$LIBC
--no-warn-rwx-segment "$@"
Makefile:1760: recipe for target 'u-boot' failed
make: *** [u-boot] Error 139
make: *** Deleting file 'u-boot'
Add dependency of CONFIG_MMC for CONFIG_DFU_MMC config to fix the errors.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
|
|
- bootstd: Add a bootmeth for ChromiumOS on x86
- x86: Use qemu-x86_64 to boot EFI installers
|
|
Bochs is convenient with QEMU on x86 since it does not require a video
BIOS. Add a driver for it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Move from using debug() to log_debug() so that we don't have to use the
__func__ parameter and can access other logging features.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
The ACPI tables are special in that they are passed to EFI as a separate
piece, independent of other tables.
Also they can be spread over two areas of memory, e.g. with QEMU we end
up with tables kept in high memory as well.
Add new global_data fields to hold this information and update the bdinfo
command to show the table areas.
Move the rom_table_end variable into the loop that uses it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
In some cases the video ROM may have been enabled previously, such as by
a previous firmware stage. Use the correct address in that case.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
A hex value is expected for the VGA mode. Add a 0x prefix, since the #
construct is not supported in SPL. We don't want to add it, due to
code-size constraints.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
When video is set up in SPL, U-Boot proper needs to use the correct
parameters so it can write to the display.
Put these in a bloblist so they are available to U-Boot proper.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
With qemu-x86_64 we need to run the video BIOS while in 32-bit mode, i.e.
SPL. Add a Kconfig option for this, adjust the Makefile rules and use
CONFIG_IS_ENABLED() where needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
