| Age | Commit message (Collapse) | Author |
|---|
|
The commit e8a9521e649f
("vf500/vf610: synchronise device trees with linux")
has synchronized U-Boot's DTS with v5.19 Linux kernel.
It turned out that in Linux's upstream iomuxc node description the
'fsl,mux_mask' was missing, so the U-Boot's pinctrl driver for NXP's
Vybrid SoC was not working properly.
As by default the mux mask was set to 0, for example the vf610 based
boards (like BK4) were bricked, due to misconfiguration of gpio at
early boot stage.
The fix for all NXP eligible boards is to define .mux_mask field for
soc specific *pinctrl_soc_info structure and use it directly in pinctrl
MMIO driver, without the need to read the "fsl,mux_mask" property from
device tree.
This change brings the NXP's pinctrl driver in U-Boot closer to Linux
upstream one.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com> #for i.MX8ULP
|
|
Ilias Apalodimas <ilias.apalodimas@linaro.org> says:
Instructions that lead ito an exception in the hypervisor can't modify two
CPU registers at once for the ARM ISA.
These instructions cannot be emulated by KVM as they do not produce
syndrome information data that KVM can use to infer the destination
register, the faulting address, whether it was a load or store, or
if it's a 32 or 64 bit general-purpose register.
As a result an external abort is injected from QEMU, via ext_dabt_pending.
Link: https://lore.kernel.org/r/20250618065828.1312146-1-ilias.apalodimas@linaro.org
|
|
A following patch is replacing our IO accessors with
do { ... } while(0) ones in order to make them usable with KVM.
That leads to an error eventually looking like this:
arch/arm/include/asm/io.h:62:9: error: expected expression before 'do'
62 | do { \
| ^~
arch/arm/include/asm/io.h:211:41: note: in expansion of macro '__raw_writel'
211 | #define out_arch(type,endian,a,v) __raw_write##type(cpu_to_##endian(v),a)
| ^~~~~~~~~~~
arch/arm/include/asm/io.h:223:25: note: in expansion of macro 'out_arch'
223 | #define out_be32(a,v) out_arch(l,be32,a,v)
| ^~~~~~~~
drivers/spi/fsl_dspi.c:127:17: note: in expansion of macro 'out_be32'
127 | out_be32(addr, val) : out_le32(addr, val);
| ^~~~~~~~
So adjust the current macros and code to be compatible with the upcoming
change.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
dw_pcie_link_set_max_link_width()"
This patch set from Marek Vasut <marek.vasut+renesas@mailbox.org>
introduces dw_pcie_link_set_max_link_width() similar to the Linux Kernel
and then migrates the current platform drivers to use it. Next it adds
support for Renesas R-Car Gen4 platforms and enables it on one.
Link: https://lore.kernel.org/r/20250617081641.8385-1-marek.vasut+renesas@mailbox.org
|
|
Add R-Car Gen4 PCIe controller support for host mode.
This controller is based on Synopsys DesignWare PCIe. However, this
particular controller has a number of vendor-specific registers, and as
such, requires initialization code, including PHY firmware loading.
The PHY firmware loading is implemented in an entirely generic manner,
by calling a firmware loading script, which the user can configure in
a way they require. This provides the user with flexibility of loading
the PCIe firmware from whichever storage device they need to load it
from.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
|
Use dw_pcie_link_set_max_link_width() instead of local implementation
of the same functionality. This does change the behavior slightly, as
the dw_pcie_link_set_max_link_width() implementation also programs the
LNKCAP register MLW, this should however be correct and is now aligned
with Linux kernel behavior.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
|
Use dw_pcie_link_set_max_link_width() instead of local implementation
of the same functionality.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
|
|
Use dw_pcie_link_set_max_link_width() instead of local implementation
of the same functionality. This does change the behavior slightly, as
the dw_pcie_link_set_max_link_width() implementation also programs the
LNKCAP register MLW, this should however be correct and is now aligned
with Linux kernel behavior.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
|
|
Add dw_pcie_link_set_max_link_width() implementation ported from Linux kernel
as of commit 89db0793c9f2 ("PCI: dwc: Add missing PCI_EXP_LNKCAP_MLW handling").
This is common code which is already duplicated in multiple drivers.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
|
Hrushikesh Salunke <h-salunke@ti.com> says:
This series adds support for the Endpoint mode on Cadence PCIe controller
on TI's K3 family of SoCs. The driver is an adaptation of the Linux
driver (drivers/pci/controller/cadence/pci-j721e.c) and has been
implemented specifically for Endpoint mode of operation on AM64X. A minor
set of changes will be sufficient to support other K3 SoCs as well.
This patch is tested on AM64X EVM. Following are the log corresponding
to this feature.
https://gist.github.com/hrushikesh221/e8557cbe7667877c50f7d7e9bb96d060
Link: https://lore.kernel.org/r/20250616164929.631791-1-h-salunke@ti.com
|
|
Add support for Endpoint mode of operation in the Cadence PCIe
Controller present on TI's K3 SoCs. This driver is an adaptation of the
Linux kernel v6.15 driver (drivers/pci/controller/cadence/pci-j721e.c).
Signed-off-by: Hrushikesh Salunke <h-salunke@ti.com>
|
|
This is a port of the corresponding commit in the Linux kernel which
adds the same support for the Cadence Torrent driver[0]. The commit
message below is taken as-is from the Linux kernel commit being ported.
The Torrent SERDES can support at most two different protocols (PHY types).
This only mandates that the device-tree sub-nodes used to represent the
configuration should describe links with at-most two different protocols.
The existing implementation however imposes an artificial constraint that
allows only two links (device-tree sub-nodes). As long as at-most two
protocols are chosen, using more than two links to describe them in an
alternating configuration is still a valid configuration of the Torrent
SERDES.
A 3-Link 2-Protocol configuration of the 4-Lane SERDES can be:
Lane 0 => Protocol 1 => Link 1
Lane 1 => Protocol 1 => Link 1
Lane 2 => Protocol 2 => Link 2
Lane 3 => Protocol 1 => Link 3
A 4-Link 2-Protocol configuration of the 4-Lane SERDES can be:
Lane 0 => Protocol 1 => Link 1
Lane 1 => Protocol 2 => Link 2
Lane 2 => Protocol 1 => Link 3
Lane 3 => Protocol 2 => Link 4
[0] https://github.com/torvalds/linux/commit/5b7b83a9839be643410c31d56f17c2d430245813
Signed-off-by: Hrushikesh Salunke <h-salunke@ti.com>
|
|
Add support for Dallas/Maxim ds1672 32bit counter RTC.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
|
|
https://source.denx.de/u-boot/custodians/u-boot-snapdragon into next
This PR introduces 3 new platforms, two from the new Dragonwing IQx
series (QCS615 and QCS8300) as well as the IPQ5424.
Additionally:
* Support for booting downstream Android boot images on some phones is
added
* Capsule update support is expanded to be more generic, determining
which partition U-Boot was flashed to automatically and supporting
many more boards.
* Minor capsule update bugs are fixed
* A watchdog driver is added and gets timeout support
* Autoboot now requires pressing "space" specifically to stop booting as
a workaround for some boards getting rogue key presses which would
cause autoboot to fail
* Documentation is added for the Dragonwing boards
* The RB1/2 now use USB gadget mode rather than host
* A bug is fixed where GPIO reads could return incorrect values
|
|
Update the variable name to sm8250_gcc_data as it's in the sm8250
driver.
Fixes: dcd688229cb ("clk/qcom: add driver for sm8250 GCC")
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Casey Connolly <casey.connolly@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250611-qcom-clk-variable-names-v1-2-37615b74daad@fairphone.com
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>
|
|
Update the variable name to sc7280_gcc_data as it's in the sc7280
driver.
Fixes: f50e7be6bb1 ("clk/qcom: add initial clock driver for sc7280")
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Casey Connolly <casey.connolly@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250611-qcom-clk-variable-names-v1-1-37615b74daad@fairphone.com
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>
|
|
Calling scsi_scan() results in all the block devices (and EFI block
devices) being destroyed and re-created. This breaks the EFI filesystem
drivers during capsule update.
Remove the call, since boards really should be calling scsi_scan()
themselves during board_init().
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Link: https://lore.kernel.org/r/20250411-b4-qcom-capsule-update-improvements-v2-3-27f6b2fcc4a9@linaro.org
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>
|
|
Port Linux's gcc-qcs615.c driver to U-Boot for basic bring-up.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Aswin Murugan <aswin.murugan@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250521035324.1182833-4-aswin.murugan@oss.qualcomm.com
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>
|
|
Enable QMP phy for QCS615, referenced from Linux.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Aswin Murugan <aswin.murugan@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250521035324.1182833-3-aswin.murugan@oss.qualcomm.com
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>
|
|
Enable QMP phy for QCS8300, referenced from Linux.
Reviewed-by: Casey Connolly <casey.connolly@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Balaji Selvanathan <balaji.selvanathan@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250529154931.1879976-5-quic_bselvana@quicinc.com
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>
|
|
* Port Linux's gcc-qcs8300.c driver to U-Boot for basic bring-up.
* Enable QCS8300 clocks in qcom_defconfig.
Reviewed-by: Casey Connolly <casey.connolly@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Balaji Selvanathan <balaji.selvanathan@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250529154931.1879976-4-quic_bselvana@quicinc.com
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>
|
|
In the current implementation, the GPIO read operation considers
both the input and outbut bits (bits 0 and 1). It should only consider
the state of input bit, i.e bit 0. To address this, mask input bit
alone and read it.
Signed-off-by: Aswin Murugan <aswin.murugan@oss.qualcomm.com>
Reviewed-by: Sumit Garg <sumit.garg@oss.qualcomm.com>
Reviewed-by: Casey Connolly <casey.connolly@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250508113646.1462518-1-aswin.murugan@oss.qualcomm.com
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>
|
|
Prepare v2025.07-rc5
With this merge, tighten up the LTO_FLAGS removal we added to not
trigger on ARMv7 (which is Thumb-2 and should be fine).
|
|
This patch enhances the Qualcomm watchdog driver by introducing
support for dynamic timeout configuration. Specifically:
- Calculates and sets the bark and bite timeout values based on
the clock rate and the requested timeout in milliseconds.
- Adds retrieval of the watchdog clock rate during probe using
the common clock framework.
- Adds a default timeout value for ARCH_SNAPDRAGON
in WATCHDOG_TIMEOUT_MSECS.
These changes improve the configurability and accuracy of the
watchdog timer on Qualcomm platforms.
This work builds upon the previous submission:
https://lore.kernel.org/all/20250422-b4-qcom-wdt-v3-1-730d4d5a858d@paulsajna.com/
Signed-off-by: Balaji Selvanathan <balaji.selvanathan@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250527124926.128413-1-balaji.selvanathan@oss.qualcomm.com
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>
|
|
Some Qualcomm device vendors decide to turn the watchdog on in the
bootloader, resulting in the device being reset if it isn't petted every
~30 seconds. Introduce a driver to keep the watchdog happy and prevent this
annoying behaviour.
Signed-off-by: Paul Sajna <hello@paulsajna.com>
Co-authored-by: Paul Sajna <hello@paulsajna.com>
Tested-by: Paul Sajna <hello@paulsajna.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Sumit Garg <sumit.garg@oss.qualcomm.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250422-b4-qcom-wdt-v3-1-730d4d5a858d@paulsajna.com
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>
|
|
Add pinctrl driver for the TLMM block found in the ipq5424 SoC.
Signed-off-by: Varadarajan Narayanan <quic_varada@quicinc.com>
Reviewed-by: Casey Connolly <casey.connolly@linaro.org>
Link: https://lore.kernel.org/r/20250304110105.2762124-6-quic_varada@quicinc.com
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>
|
|
Add initial set of clocks and resets for enabling U-Boot on ipq5424
based RDP platforms.
Signed-off-by: Varadarajan Narayanan <quic_varada@quicinc.com>
Reviewed-by: Casey Connolly <casey.connolly@linaro.org>
Link: https://lore.kernel.org/r/20250304110105.2762124-5-quic_varada@quicinc.com
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>
|
|
Device bus address might not be valid for direct access when the bus
address and CPU address are not the same. Use dev_bus_to_phys() to
translate bus address back to CPU address.
Fixes: 3d98b8c504e15 ("net: designware: Invalidate RX buffer cache before freeing the DMA descriptor")
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
|
|
Marek Vasut <marek.vasut+renesas@mailbox.org> says:
Rename the environment related variables and add ENV_ prefix, so that
all configuration options which are related to environment would have
an CONFIG_ENV_ prefix. No functional change.
Link: https://lore.kernel.org/r/20250609192701.20260-1-marek.vasut+renesas@mailbox.org
|
|
Rename the variable and add ENV_ prefix, so that all configuration
options which are related to environment would have an CONFIG_ENV_
prefix. No functional change.
Use ENV_MMC_DEVICE_INDEX to clarify this is the SD/MMC device
index, a number, as enumerated by U-Boot. Update the help text
accordingly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
|
https://source.denx.de/u-boot/custodians/u-boot-at91 into next
First set of u-boot-at91 features for the 2025.10 cycle:
This feature set includes the addition of new sam9x7 SoC and a new board
named sam9x7-curiosity. There is also new support for sam9x60 compatible
at91 watchdog.
|
|
into next
- Assorted cleanups and R-Car Gen4 watchdog driver
|
|
Add PMC driver support for sam9x7 SoC family
Signed-off-by: Varshini Rajendran <varshini.rajendran@microchip.com>
[balamanikandan.gunasundar@microchip.com: Add peripheral clock id for pmecc]
Signed-off-by: Balamanikandan Gunasundar <balamanikandan.gunasundar@microchip.com>
|
|
The clk_register function logs an error if parent_name is missing from the
Device Tree.On the SAM9X7, the main_rc node is omitted to stay aligned with
the Linux Device Tree.Remove the parent_name check in at91_clk_main_rc()
to allow it to pass NULL when the parent is not specified.
Signed-off-by: Manikandan Muralidharan <manikandan.m@microchip.com>
|
|
Add support for hardware dividers for PLL IDs.In sam9x7 SoC,
PLL_ID_PLLA and PLL_ID_PLLA_DIV2 has /2 hardware dividers
each.
fcorepllack -----> HW Div = 2 -+--> fpllack
|
+--> HW Div = 2 ---> fplladiv2ck
Signed-off-by: Varshini Rajendran <varshini.rajendran@microchip.com>
|
|
Add support for different core clock frequency input ranges
for different PLL IDs in the PLL driver and align sam9x60, sama7g5 SOC
platforms.
Signed-off-by: Varshini Rajendran <varshini.rajendran@microchip.com>
|
|
SAM9X60 has a slightly different watchdog implementation:
- Timer value moved into a new register WLR
- Some MR register fields have their position changed
This patch add SAM9X60 support, also adds a compatible
for SAMA5D4 which is the same as existing SAM9260.
Signed-off-by: Zixun LI <admin@hifiphile.com>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
"wdt" is a better name for watchdog rather than generic "priv".
Signed-off-by: Zixun LI <admin@hifiphile.com>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
Use the name "mr" since we are referring to timer mode register.
Signed-off-by: Zixun LI <admin@hifiphile.com>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
Moteen Shah <m-shah@ti.com> says:
This patch series adds the functionality to print the DM firmware
version being used. Before requesting TISCI for the DM version we
first check if the DM split mode capability exists, if yes, we proceed
onto making the call to TISCI for retrieving the version information.
DM split mode capability indicates that the DM is a separate binary
altogether and has its own versioning information similar to TIFS.
Boot Logs: https://gist.github.com/Jamm02/37864f605445944a0c0caf426e0aba50
Link: https://software-dl.ti.com/tisci/esd/latest/2_tisci_msgs/general/core.html#tisci-msg-query-fw-caps
Link: https://lore.kernel.org/r/20250609081434.1000377-1-m-shah@ti.com
|
|
Beleswar Padhi <b-padhi@ti.com> says:
This series adds remoteproc support on MCU R5F in Split mode.
During boot, ROM can bring up the boot R5F cores in either lockstep or
split mode based on X509 certificate flags. If booted in lockstep mode,
the MCU R5F cores will run first the R5 SPL, and then once A72 comes up,
will run the Device Manager (DM) firmware. But if booted in split mode, core
0 will run DM firmware and second core sits in WFI. Shut it down so that
other firmwares can later be loaded on them.
The shutdown of MCU R5 Core 1 is invoked at A72 SPL init, as by that
time Device Manager (DM) is up and running on R5 Core 0. The shutdown
of MCU R5 Core 1 is handled by Device Manager itself.
Test logs:
https://gist.github.com/3V3RYONE/ee8e3cb9aa5f4c5c00b059b9c14bfa98
Link: https://lore.kernel.org/r/20250609081429.1724643-1-b-padhi@ti.com
|
|
Add a function to retrieve information of the DM firmware's ABI versions,
RM/PM HAL, firmware version, etc using TI_SCI protocol.
Signed-off-by: Moteen Shah <m-shah@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
|
|
Add a new function to query the capabilities of the DM firmware, using
TI SCI protocol to retrieve a 64-bit firmware capability, where each bit
represents a specific capability supported by the firmware.
Signed-off-by: Moteen Shah <m-shah@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
|
|
Introduce response and request structs to receive and request
information regarding DM version, etc from TI SCI.
Signed-off-by: Moteen Shah <m-shah@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
|
|
Introduce response and request structs for receiving information
regarding FW/SOC capability from DM. The received capability can
further be used to call certain API's based on the feature supoorted
by the DM firmware.
Signed-off-by: Moteen Shah <m-shah@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
|
|
Acquire processor control before doing core reset operations in probe
routine. Release the control afterwards, so that it can be acquired
during core loading operations.
Signed-off-by: Beleswar Padhi <b-padhi@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
|
|
Add support of Renesas R-Car Gen4 watchdog timer. Timeouts up to
8184.0s are supported (CKS1 register is not involved). The watchdog
uses the clock of type CLK_TYPE_GEN4_MDSEL.
The timeout is set in
dts/upstream/src/arm64/renesas/r8a779f0-spider-cpu.dtsi section &rwdt.
This driver is based on upstream linux commit:
e70140ba0d2b("Get rid of 'remove_new' relic from platform driver struct")
Signed-off-by: Shmuel Leib Melamud <smelamud@redhat.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
|
Rasmus Villemoes <ravi@prevas.dk> says:
While looking through list.h, I saw that the regular list_* helpers
(and one of the hlist_* ones) still contain the prefetch() that was
removed in linux 14 years ago. It doesn't do anything, but makes the
macros harder to read, so get rid of it, and the fallback, no-op
definition that they relied on. That requires removing a few uses
outside list.h as well.
checkpatch warns about some whitespace issues in list.h, but as I've
copied whole kerneldoc+#define blocks directly from the linux kernel,
I think it's better to just accept that so that we don't introduce
needless diffs. The "macro argument reuse" arguments should also be
ignored, as e.g. the "member" arguments are obviously always just bare
identifiers, and the "pos" arguments must be assigned to multiple
times.
Link: https://lore.kernel.org/r/20250507121246.518691-1-ravi@prevas.dk
|
|
These all end up using the no-op prefetch() defined in linux/list.h,
because the only possible real implementation is in
arch/mips/include/asm/processor.h, which is behing
CONFIG_CPU_HAS_PREFETCH which is nowhere defined.
In order to be able to drop that fallback definition from list.h,
first remove all uses.
Signed-off-by: Rasmus Villemoes <ravi@prevas.dk>
|
|
Add support of CLK_TYPE_GEN4_MDSEL clock type to gen3_clk_get_rate64()
function. In particular, this type of clock is used by Renesas R-Car
Gen4 watchdog. It operates similarly to CLK_TYPE_GEN3_MDSEL clock.
Signed-off-by: Shmuel Leib Melamud <smelamud@redhat.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@kernel.org>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Stefan Roese <sr@denx.de>
|
