| Age | Commit message (Collapse) | Author |
|---|
|
This conditional always evaluated as false, regardless of the value of reg.
Fix it so that it properly tests the bits in the PLL register. Also test
PLL_EN, now that we set it.
Reported-by: Damien Le Moal <Damien.LeMoal@wdc.com>
Signed-off-by: Sean Anderson <seanga2@gmail.com>
|
|
After starting or setting the rate of a PLL, the enable bit must be set.
This fixes a bug where the AI ram would not be accessible, because it
requires PLL1 to be running.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
|
|
If the user/dev explicitly requests a clock be assigned a certain rate,
then we should warn them if we can't do it. This makes it clear if the
clock is running at the default rate.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
|
|
This patch changes the functioning of the detection of w1 devices.
The old way was a comparison between detected w1 and the ones described in
the device tree. Now it will just look for the driver matching the family
id of the w1 detected.
The patch is inspired from Maxime Ripard code.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Maxime Ripard <maxime@cerno.tech>
|
|
https://source.denx.de/u-boot/custodians/u-boot-ti
- Initial support for AM64 EVM and SK
- K3 DDR driver unification for J7 and AM64 platforms.
- Minor fixes for TI clock driver
|
|
Add a new compatible to support AM64 SoC
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Currently driver may end up caching disabled port ID as active
interface. Fix this by bailing out earlier in case port is marked
disabled in the DT.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
CPSW NUSS IP on K3 SoCs can have more than one external port (upto 8)
Therefore increase AM65_CPSW_CPSWNU_MAX_PORTS to 9 (8 ext + 1 Root port)
as preparation to allow any one of the 8 ports to be used as ethernet
interface in U-Boot.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Sync BCDMA and PKTDMA support from Kernel for AM64 SoC
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Add AM64 SoC specific channel mapping and endpoint data.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Extend PSIL EP data to include AM64 DMA specific information
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
ICSSG Ethernet driver uses two src threads per port (one per slice).
Similarly CPSW uses one src thread.
Drop PSIL EP static data for other src threads in order to reduce
R5 SPL footprint. This makes AM65x board bootable again.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
With AM64x supporting only K3_NAV_RINGACC_RING_MODE_RING or the exposed
ring mode, all other K3 SoCs have also been moved to this common
baseline. Therefore drop other modes such as
K3_NAV_RINGACC_RING_MODE_MESSAGE (and proxy) to save on SPL footprint.
There is a saving of ~800 bytes with this change for am65x_evm_r5_defconfig.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
|
|
AM64 dual mode rings are modeled as pair of Rings objects which has common
configuration and memory buffer, but separate real-time control register
sets for each direction mem2dev (forward) and dev2mem (reverse).
AM64 rings must be requested only using k3_ringacc_request_rings_pair(),
and forward ring must always be initialized/configured. After this any
other Ringacc APIs can be used without any callers changes.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Update struct ti_sci_msg_rm_udmap_tx_ch_cfg_req to latest ABI to support
AM64x BCDMA Block copy channels.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Add support for AM64 SoC identification.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Attempt to get and enable a vtt regulator if one is provided from the
dts. If we do not find one, continue as not all platforms have this.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
|
|
Introduce support for the AM64 DDRSS controller which uses the 16bit
variation of the controller. This controller shares much functionality
with the existing J721e support, so this patch introduces only the new
code needed for am64 specific support from "_16bit_" files with headers
under "16bit/" include path/.
Also add a CONFIG_K3_AM64_DDRSS option to the choice required for use
with CONFIG_K3_DDRSS to allow selecting AM64 support.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
|
|
Introduce a new version of the ddr driver which has the ability to
support different variations of the controller. Also introduce support
for the 32bit variation of the controller which is what was already
supported by the previous version used for J721e and J7200.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
|
|
Create a new CONFIG_K3_DDRSS option to select the common parts of the
k3-ddrss driver. Also introduce a choice that depends on the top level
option to select CONFIG_K3_J721E_DDRSS for j721e support, and update
corresponding Kconfig as required.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
|
|
Rename the k3-j721e folder under drivers/ram to k3-ddrss in preparation
of introducing additional support for other platforms to the same
driver.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
|
|
Use Linux style u32 instead of uint32_t.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
|
|
Fix the indentation for certain macros to be consistent with the other
macros in the file, as the existing indentation does not make sense in
many places.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
|
|
Fix the indentation for certain macros to be consistent with the other
macros in the file, as the existing indentation does not make sense in
many places.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
|
|
Fix the indentation for certain macros to be consistent with the other
macros in the file, as the existing indentation does not make sense in
many places.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
|
|
Fix the indentation for certain macros to be consistent with the other
macros in the file, as the existing indentation does not make sense in
many places.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
|
|
Fix the indentation for certain macros to be consistent with the other
macros in the file, as the existing indentation does not make sense in
many places.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
|
|
Fix the indentation for certain macros to be consistent with the other
macros in the file, as the existing indentation does not make sense in
many places.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
|
|
Fix the indentation for certain macros to be consistent with the other
macros in the file, as the existing indentation does not make sense in
many places.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
|
|
Fix the indentation for certain macros to be consistent with the other
macros in the file, as the existing indentation does not make sense in
many places.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
|
|
AM64x uses a different thread mapping that existing K3 SoCs, so update
the valid thread ID list to include those used for AM64x.
Also remove the comment identifying the purpose of each thread ID. The
purpose of the thread ID is specified when describing the threads in the
device tree and the same ID can mean different things on different SoCs,
so the comment is not useful.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
|
|
Add support for the controller present on the AM642 SoC.
There are instances:
sdhci0: 8bit bus width, max 400 MBps
sdhci1: 4bit bus width, max 100 MBps
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
|
|
This reverts commit d64b9cdcd475eb7f07b49741ded87e24dae4a5fc.
As pointed by [1] and [2], the reverted patch made every DT 'reg'
property translatable. What the patch was trying to fix was fixed in a
different way from previously submitted patches which instead of
correcting the generic address translation function fixed the issue with
appropriate platform code.
[1] https://patchwork.ozlabs.org/project/uboot/patch/1614324949-61314-1-git-send-email-bmeng.cn@gmail.com/
[2] https://lore.kernel.org/linux-clk/20210402192054.7934-1-dariobin@libero.it/T/
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Using the custom TI functions required not only replacing common memory
access functions but also rewriting the routines used to set bypass and
lock states. As for readl() and writel(), they also required the address
of the register to be accessed, a parameter that is hidden by the TI clk
module.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
|
|
Replaces the common memory access functions used by the driver with the
ones exported from the TI clk module.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
|
|
The clock access functions exported by the clk header use the
struct clk_ti_reg parameter to get the address of the register. This
must also apply to clk_ti_latch(). Changes to TI's clk-mux and
clk-divider drivers prevented the patch from generating compile errors.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
|
|
As pointed by [1] and [2], commit
d64b9cdcd4 ("fdt: translate address if #size-cells = <0>") is wrong:
- It makes every 'reg' DT property translatable. It changes the address
translation so that for an I2C 'reg' address you'll get back as reg
the I2C controller address + reg value.
- The quirk must be fixed with platform code.
The clk_ti_get_reg_addr() is the platform code able to make the correct
address translation for the AM33xx clocks registers. Its implementation
was inspired by the Linux Kernel code.
[1] https://patchwork.ozlabs.org/project/uboot/patch/1614324949-61314-1-git-send-email-bmeng.cn@gmail.com/
[2] https://lore.kernel.org/linux-clk/20210402192054.7934-1-dariobin@libero.it/T/
Signed-off-by: Dario Binacchi <dariobin@libero.it>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-imx
u-boot-imx-20210502
-------------------
- mx6: fixes for Ventana
- local fixes from maintainer
- imx7d: Ronetix's iMX7-CM
- imx8: Ronetix iMX8MQ-CM
Engicam i.Core MX8M
Compulab iot-gate-imx8
- Fixes i.MX8 documentation
- Fixes phy usage with fec
|
|
As it has been now two years past the migration deadline, it is required
to have migrated. Remove the check from the Makefile and rework some of
the Kconfig logic slightly to get the functional dependencies of DM_MMC
/ BLK right in both the SPL and non-SPL case.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
The migration deadline for having LIBATA mean that AHCI is also enabled
was v2019.07. As that has long since passed, adjust the Kconfig
dependencies.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
|
|
Adding timeout mechanism to avoid spi driver from stucking
in the while loop in __atcspi200_spi_xfer().
Signed-off-by: Dylan Jhong <dylan@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
|
|
This uses the newly-added dm_gpio_get_values_as_int_base3 function to
implement a sysinfo device. The revision map is stored in the device tree.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This has the uclass enforce calling detect() before other methods. This
allows drivers to cache information in detect() and perform (cheaper)
retrieval in the other accessors. This also modifies the only instance
where this sequencing was not followed.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Since 07c9e683a4 ("smbios: Allow a few values to come from sysinfo")
there are common global sysinfo IDs. This patch moved existing IDs above
SYSINFO_ID_USER.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
of_parse_phandle_with_args (called by dev_read_phandle_with_args) does not
support getting the length of a phandle list by using the index -1.
Instead, use dev_count_phandle_with_args which supports exactly this
use-case.
Fixes: 8558217153 ("gpio: Convert to use APIs which support live DT")
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
commit 6ecbe1375671 ("drivers: pci: imx: add imx_pcie_remove function")
attempted to resolve an issue caused by MX6QDL not having a proper
intneral PCIe core reset and thus hanging during kernel init if the
bootloader had enabled PCI.
The issue exists for IMX6Q, IMX6D, IXM6S, and IMX6DL. Fix the case for
IMX6S and IMX6DL getting missed.
This fixes IMX6S and IMX6DL with PCI enabled in U-Boot booting for
Linux v4.11+.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
|
|
If we fail to probe for whatever reason, we cannot unregister/free the
MII bus unless we registered it with fec_get_miibus. This fixes FECs
sharing an MDIO bus from destroying it, preventing the other FEC from
using it.
Fixes: 6a895d039b ("net: Update eQos driver and FEC driver to use eth phy interfaces")
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
|
|
If a phy is disabled, don't use it. This matches Linux's behavior.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
|
|
Add a board_pci_fixup_dev weak function to allow PCI device fixups
during enumeration.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
|
