| Age | Commit message (Collapse) | Author |
|---|
|
various minor sandbox improvements
|
|
- Update CI to use gcc-11.1 and clang-11 to build everything. This
requires a few fixes to the code that these newer compilers have
exposed.
|
|
With gcc-11 we get a multiple errors here as the declarations for
mscc_pinctrl_ops and mscc_gpio_ops are missing an extern.
CC: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: Lars Povlsen <lars.povlsen@microchip.com>
Cc: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
|
|
With gcc-11 we see:
drivers/ddr/marvell/a38x/ddr3_debug.c:672:47: error: argument 2 of type 'u32[5]' {aka 'unsigned int[5]'} with mismatched bound [-Werror=array-parameter=]
672 | int ddr3_tip_read_adll_value(u32 dev_num, u32 pup_values[MAX_INTERFACE_NUM * MAX_BUS_NUM],
| ~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from drivers/ddr/marvell/a38x/ddr3_training_ip_engine.h:10,
from drivers/ddr/marvell/a38x/ddr3_init.h:17,
from drivers/ddr/marvell/a38x/ddr3_debug.c:6:
drivers/ddr/marvell/a38x/ddr3_training_ip_flow.h:116:47: note: previously declared as 'u32[]' {aka 'unsigned int[]'}
And similar warnings. Correct these by updating the prototype. Remove
the prototype for ddr3_tip_read_pup_value as it is unused.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
https://source.denx.de/u-boot/custodians/u-boot-atmel
First set of u-boot-atmel fixes for 2021.10 cycle:
This small fixes set is dedicated to fixing the onewire subsystem for
the at91 boards which was broken since 2020.04.
|
|
- mpc8379erdb DM_USB, DM_PCI and DM_ETH support.
- Drop PCI support from the integrator family of boards
- Add synquacer support
- Assorted lpc32xx updates and improvements
- snapdragon (and related) fixes, Broadcom iproc update
|
|
At the moment, the U-Boot serial_msm driver does not initialize the
UART_DM_DMEN register with the required value. Usually this does not
cause any problems, because there is Qualcomm's LK bootloader running
before U-Boot which initializes the register with the correct value.
It's important that this register is initialized correctly, because
the U-Boot driver does not make use of the BAM/DMA or single character
mode functionality of the UART controller. A different bootloader
before U-Boot might initialize the register differently.
For example, on DragonBoard 410c U-Boot can also be installed to the
"aboot" partition (replacing LK entirely). In this case U-Boot is
loaded directly by SBL, which seems to use the single-character mode
for some reason. In single character mode there is always just one
char in the FIFO, instead of the 4 characters expected by
msm_serial_fetch(). It also causes issues with "earlycon" later in
the Linux kernel, which tries to output 4 chars at once,
but only the first char will be written.
This causes early UART log in Linux to be corrupted like this:
[ 00ano:ameoi .Q1B[ 00ac _idaM00080oo'ahani-lcle._20). 15NdNii 5 SPMSJ20:U2
[ 00rkoolmsamel
[ 00Fw ]elamletopsioble
[ 00ore
instead of
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd030]
[ 0.000000] Machine model: Qualcomm Technologies, Inc. APQ 8016 SBC
[ 0.000000] earlycon: msm_serial_dm0 at MMIO 0x00000000078b0000 (options '')
[ 0.000000] printk: bootconsole [msm_serial_dm0] enabled
Make sure to initialize UART_DM_DMEN correctly to fix this issue
when loading U-Boot directly after SBL (instead of through LK).
There is no functional difference when loading U-Boot through LK
since LK also initializes UART_DM_DMEN to 0x0. [1]
[1]: https://git.linaro.org/landing-teams/working/qualcomm/lk.git/tree/platform/msm_shared/uart_dm.c?h=dragonboard410c-LA.BR.1.2.7-03810-8x16.0-linaro3#n203
Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
|
|
Convert the CONFIG_SYS_I2C_LPC32XX configuration symbol from an include
directive to a Kconfig value.
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Add the of_match/compatible string to the lpc32xx i2c driver so it works
correctly with device-tree.
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
|
|
The lpc32xx driver was not obtaining the per-device base address correctly
from the device tree. Fix the FIXME in order to get the correct base address.
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
|
|
The LPC32XX_I2C_STAT_DRMI is not used anywhere so remove it.
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
|
|
Add driver for class of I2C controllers found on
Socionext Synquacer platform.
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
This is a driver for the HSSPI SPI controller on SynQuacer SoC.
The HSSPI has command sequence mode (memory mapped) and
direct mode (FIFO access). The driver will operate it under
the direct mode. And before booting OS, it switch back to the
command sequence mode since that is compatible with default
EDK2 behavior.
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
|
|
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
Add ECAM based SynQuacer PCIe RC driver. This driver configures the
PCIe RC and filter out a ghost pcie config.
Since the Linux kernel expects "socionext,synquacer-pcie-ecam" device
is configured by firmware (EDK2), it doesn't re-configure in the kernel.
So as same as EDK2, U-Boot needs to configure it before boot the kernel.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
|
|
Commit bbbcb5262839 ("dm: pci: Enable VGA address forwarding on bridges")
sets the VGA bridge bits by checking pplat->class, but if the parent
device is the pci host bus device, it can be skipped. Moreover, it
shouldn't access the pplat because the parent has different plat data.
Without this fix, "pci enum" command cause a synchronous abort.
pci_auto_config_devices: start
PCI Autoconfig: Bus Memory region: [78000000-7fffffff],
Physical Memory [78000000-7fffffffx]
PCI Autoconfig: Bus I/O region: [0-ffff],
Physical Memory [77f00000-77f0ffffx]
pci_auto_config_devices: device pci_6:0.0
PCI Autoconfig: BAR 0, Mem, size=0x1000000, address=0x78000000 bus_lower=0x79000000
PCI Autoconfig: BAR 1, Mem, size=0x8000000, No room in resource, avail start=79000000 / size=8000000, need=8000000
PCI: Failed autoconfig bar 14
PCI Autoconfig: BAR 2, I/O, size=0x4, address=0x1000 bus_lower=0x1004
PCI Autoconfig: BAR 3, Mem, size=0x2000000, address=0x7a000000 bus_lower=0x7c000000
PCI Autoconfig: BAR 4, I/O, size=0x80, address=0x1080 bus_lower=0x1100
PCI Autoconfig: ROM, size=0x80000, address=0x7c000000 bus_lower=0x7c080000
"Synchronous Abort" handler, esr 0x96000006
elr: 00000000e002bd28 lr : 00000000e002bce8 (reloc)
elr: 00000000fff6fd28 lr : 00000000fff6fce8
x0 : 0000000000001041 x1 : 000000000000003e
x2 : 00000000ffb0f8c8 x3 : 0000000000000001
x4 : 0000000000000080 x5 : 0000000000000000
x6 : 00000000fff718fc x7 : 000000000000000f
x8 : 00000000ffb0f238 x9 : 0000000000000008
x10: 0000000000000000 x11: 0000000000000010
x12: 0000000000000006 x13: 000000000001869f
x14: 00000000ffb0fcd0 x15: 0000000000000020
x16: 00000000fff71cc4 x17: 0000000000000000
x18: 00000000ffb13d90 x19: 00000000ffb14320
x20: 0000000000000000 x21: 00000000ffb14090
x22: 00000000ffb0f8c8 x23: 0000000000000001
x24: 00000000ffb14c10 x25: 0000000000000000
x26: 0000000000000000 x27: 0000000000000000
x28: 00000000ffb14c70 x29: 00000000ffb0f830
Code: 52800843 52800061 52800e00 97ffcf65 (b9400280)
Resetting CPU ...
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Without this fix, scsi-scan will cause a synchronous abort
when accessing ops->scan.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This patch adds a limited pulse-width modulator to sandbox's Chromium OS
Embedded Controller emulation. The emulated PWM device supports multiple
channels but can only set a duty cycle for each, as the actual EC
doesn't expose any functionality or information other than that. Though
the EC supports specifying the PWM channel by its type (e.g. display
backlight, keyboard backlight), this is not implemented in the emulation
as nothing in U-Boot uses this type specification.
This emulated PWM device is then used to test the Chromium OS PWM driver
in sandbox. Adding the required device node to the sandbox test
device-tree unfortunately makes it the first PWM device, so this also
touches some other tests to make sure they still use the sandbox PWM.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Each _device_ belonging to a given uclass of course has its own ->ops,
of a type determined by and known to the uclass.
However, no instance of a uclass_driver seems to populate ->ops, and
the only reference to it in code is this relocation.
Moreover, it's not really clear what could sensibly be assigned; it
would have to be some "struct uclass_ops *" providing a set of methods
for the core to call on that particular uclass, but should the need
for that ever arise, it would be better to have a member of that
particular type instead of void*.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Define LOG_CATEGORY for all uclass to allow filtering with
log command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
|
|
gpio_request_by_name should be called with proper flags.
The 0 value flag is invalid, and causes bad initialization of the gpio.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
|
|
This commit adds support to piton_mmc driver for OpenPiton-riscv64
This driver has many things set as preconfigured because the hardware
automatically configures most of the settings during startup.
Signed-off-by: Tianrui Wei <tianrui-wei@outlook.com>
Signed-off-by: Jonathan Balkind <jbalkind@ucsb.edu>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
Replace 'pciaux' with 'pcieaux', including name string and function
prefix. The old name string, 'pciaux', might cause an error if PCIe
driver is changed to use clk_get_by_name() with 'pcieaux' to get
clock.
Signed-off-by: Green Wan <green.wan@sifive.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
|
|
Remove the define EQOS_DESCRIPTOR_ALIGN unused since the
commit 6f1e668d964e ("net: dwc_eth_qos: Pad descriptors to cacheline size")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
|
|
Make sure that errors in the PHY driver .startup() method, such as no
link, are propagated and not ignored.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
|
|
The RGMII spec supports optional in-band status reporting for the speed
and duplex negotiated on the copper side, and the ENETC driver enables
this feature by default.
However, this does not work when the PHY does not implement the in-band
reporting, or when there is a MAC-to-MAC connection described using a
fixed-link. In that case, it would be better to disable the feature in
the ENETC MAC and always force the speed and duplex to the values that
were negotiated and retrieved over MDIO once the autoneg is finished.
Since this works always, we just do it unconditionally and drop the
in-band code.
Note that because we need to wait for the autoneg to complete, we need
to move enetc_setup_mac_iface() after phy_startup() returns, and then
pass the phydev pointer all the way to enetc_init_rgmii().
The same considerations have led to a similar Linux driver patch as well:
https://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next.git/commit/?id=c76a97218dcbb2cb7cec1404ace43ef96c87d874
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
|
|
Given that even a fixed-link has an associated phy_device, there is no
reason to operate in a mode when dm_eth_phy_connect fails.
Remove the driver checks for a NULL priv->phy and just return -ENODEV
when that happens.
Copyright updated according to corporate requirements.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
|
|
The SMC911x Ethernet MACs can be integrated using a 16 or 32-bit bus.
The driver needs to know about this choice, which is the reason for us
having a Kconfig symbol for that.
Now this bus width is already described using a devicetree property, and
since the driver is DM compliant and is using the DT now, we should query
this at runtime. We leave the Kconfig choice around, in case the DT is
missing this property.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
|
|
The SMC911x Ethernet driver needs to know which accessor functions it
can use to access the MMIO registers. For that reason we have a Kconfig
choice between 16 and 32-bit bus width.
Since it's only those two options that we (and the Linux kernel)
support, and there does not seem to be any evidence of another bus
width anywhere, limit the Kconfig construct to a simple symbol.
This simplifies the code and allows a later rework to be much easier.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
|
|
Add nxp tja1103 phy driver.
Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
|
|
|
|
https://source.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2021.10
clk:
- Add driver for Xilinx Clocking Wizard IP
fdt:
- Also record architecture in /fit-images
net:
- Fix plat/priv data handling in axi emac
- Add support for 10G/25G speeds
pca953x:
- Add missing dependency on i2c
serial:
- Fix dependencies for DEBUG uart for pl010/pl011
- Add setconfig option for cadence serial driver
watchdog:
- Add cadence wdt expire now function
zynq:
- Update DT bindings to reflect the latest state and descriptions
zynqmp:
- Update DT bindings to reflect the latest state and descriptions
- SPL: Add support for ECC DRAM initialization
- Fix R5 core 1 handling logic
- Enable firmware driver for mini configurations
- Enable secure boot, regulators, wdt
- Add support xck devices and 67dr
- Add psu init for sm/smk-k26 SOMs
- Add handling for MMC seq number via mmc_get_env_dev()
- Handle reserved memory locations
- Add support for u-boot.itb generation for secure OS
- Handle BL32 handoffs for secure OS
- Add support for 64bit addresses for u-boot.its generation
- Change eeprom handling via nvmem aliases
|
|
It is working in a way that only minimal timeout is setup to reach
expiration just right after it is setup.
Please make sure that PMUFW is compiled with ENABLE_EM flag.
On U-Boot prompt you can test it like:
ZynqMP> wdt dev watchdog@fd4d0000
ZynqMP> wdt list
watchdog@fd4d0000 (cdns_wdt)
ZynqMP> wdt dev
dev: watchdog@fd4d0000
ZynqMP> wdt expire
(And reset should happen here)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
into next
- Cypress s25hl-t/s25hs-t support (Takahiro Kuwano)
|
|
The spi_get_bus_and_cs() may be called on the same bus and chipselect
with different frequency or mode. This is valid usecase, but the code
fails to notify the controller of such a configuration change. Call
spi_set_speed_mode() in case bus frequency or bus mode changed to let
the controller update the configuration.
The problem can easily be triggered using the sspi command:
=> sspi 0:0@1000
=> sspi 0:0@2000
Without this patch, both transfers happen at 1000 Hz. With this patch,
the later transfer happens correctly at 2000 Hz.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
|
Fixes mode clocks for SPINOR_OP_READ_FAST_4B in tiny.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
The nor->ready() and spansion_sr_ready() introduced earlier in this
series are used for multi-die package parts.
The nor->quad_enable() sets the volatile QE bit on each die.
The nor->erase() is hooked if the device is not configured to uniform
sectors, assuming it has 32 x 4KB sectors overlaid on bottom address.
Other configurations, top and split, are not supported at this point.
Will submit additional patches to support it as needed.
The post_bfpt/sfdp() fixes the params wrongly advertised in SFDP.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Cypress chips support SPINOR_OP_EN4B(B7h) to enable 4-byte addressing mode.
Cypress chips support B8h to disable 4-byte addressing mode instead of
SPINOR_OP_EX4B(E9h).
This patch defines new opcode and updates set_4byte() to support
enable/disable 4-byte addressing mode for Cypress chips.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
The spansion_sr_ready() reads status register 1 by Read Any Register
commnad. This function is called from Flash specific hook with die address
and dummy cycles to support multi-die package parts from Spansion/Cypress.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
For dual/quad die package devices from Spansion/Cypress, the device's
status needs to be checked by reading status registers in all dies, by
using Read Any Register command. To support this, a Flash specific hook
that can overwrite the legacy status check is needed.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Some of Spansion/Cypress chips support volatile version of configuration
registers and it is recommended to update volatile registers in the field
application due to a risk of the non-volatile registers corruption by
power interrupt. This patch adds a function to set Quad Enable bit in CFR1
volatile.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Some of Spansion/Cypress chips support Read/Write Any Register commands.
These commands are mainly used to write volatile registers and access to
the registers in second and subsequent die for multi-die package parts.
The Read Any Register instruction (65h) is followed by register address
and dummy cycles, then the selected register byte is returned.
The Write Any Register instruction (71h) is followed by register address
and register byte to write.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
The S25HL-T/S25HS-T family is the Cypress Semper Flash with Quad SPI.
https://www.cypress.com/file/424146/download (256Mb/512Mb/1Gb, single die)
https://www.cypress.com/file/499246/download (2Gb/4Gb, dual/quad die)
The full version can be found in the following links (registration
required).
https://community.cypress.com/t5/Semper-Flash-Access-Program/Datasheet-Semper-Flash-with-Quad-SPI/ta-p/260789?attachment-id=19522
https://community.cypress.com/t5/Semper-Flash-Access-Program/Datasheet-2Gb-MCP-Semper-Flash-with-Quad-SPI/ta-p/260823?attachment-id=29503
S25HL/HS-T (Semper Flash with Quad SPI) Family has user-configurable
sector architecture. By default, the 512Mb and 1Gb, single-die package
parts are configured to non-uniform that 4KB sectors overlaid on bottom
address. To support this, an erase hook makes overlaid sectors appear as
uniform sectors. The 2Gb, dual-die package parts are configured to uniform
by default.
Tested on Xilinx Zynq-7000 FPGA board.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
into next
- V3U Falcon board support
|
|
into next
- xSPI Octal DTR support (Pratyush Yadav)
- MXIC SPI driver (Zhengxun)
|
|
Prepare v2021.07-rc5
# gpg: Signature made Mon 28 Jun 2021 03:39:36 PM EDT
# gpg: using RSA key 1A3C7F70E08FAB1707809BBF147C39FF9634B72C
# gpg: Good signature from "Thomas Rini <trini@konsulko.com>" [ultimate]
# Conflicts:
# configs/am64x_evm_r5_defconfig
|
|
Add support for 10G/25G (XXV) high speed ethernet. This Makes use of
the exiting AXI DMA, similar to 1G.
Signed-off-by: Alessandro Temil <atemil@waymo.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
There are lot of accesses to priv data in of_to_plat(), which is incorrect.
Create a platform data structure and use it in of_to_plat(), then copy all
platform data to priv data in probe.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
This adds serial parameters that include stop bit mode, parity mode,
and character length. Mark parity and space parity modes are not
supported.
At the moment, the only path to call setconfig directly is DM testing,
however, this affects the size of SPL for DM testing, so it doesn't
apply to SPL.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
