| Age | Commit message (Collapse) | Author |
|---|
|
With MMC_PWRSEQ enabled the following link issue may happen when
building SPL and SPL_PWRSEQ is not enabled.
aarch64-linux-gnu-ld.bfd: drivers/mmc/meson_gx_mmc.o: in function `meson_mmc_probe':
drivers/mmc/meson_gx_mmc.c:295: undefined reference to `pwrseq_set_power'
Fix this by adding a SPL_MMC_PWRSEQ Kconfig option used to enable mmc
pwrseq support in SPL.
Also add depends on DM_GPIO to fix following link issue:
aarch64-linux-gnu-ld.bfd: drivers/mmc/mmc-pwrseq.o: in function `mmc_pwrseq_set_power':
drivers/mmc/mmc-pwrseq.c:26: undefined reference to `gpio_request_by_name'
aarch64-linux-gnu-ld.bfd: drivers/mmc/mmc-pwrseq.c:29: undefined reference to `dm_gpio_set_value'
aarch64-linux-gnu-ld.bfd: drivers/mmc/mmc-pwrseq.c:31: undefined reference to `dm_gpio_set_value'
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Ferass El Hafidi <vitali64pmemail@protonmail.com>
|
|
U-Boot does not support building kernel modules.
Fixes: 3c0dbed232bd ("mmc: arm_pl180_mmci: adapt driver to DM usage")
Fixes: 36645f45a048 ("drivers: mmc: Add sdhci driver for Broadcom iProc platform")
Fixes: dadd43c14368 ("mmc: synquacer: Add SynQuacer F_SDH30 SDHCI driver")
Fixes: b312c590bcd8 ("mmc: Add MMC support for stm32h7 Socs")
Fixes: d24b69395949 ("mmc: mtk-sd: add SD/MMC host controller driver for MT7623 SoC")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
If the CSD register contains a reserved value (4 - 7) in bits 0:2 of the
TRAN_SPEED field, a buffer overrun occurs. Resize the mapping table.
According to the original report
https://lore.kernel.org/u-boot/20180826231332.2491-11-erosca@de.adit-jv.com/
reserved values have been observed resulting in a buffer overrun.
Reported-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Fixes: 272cc70b211e ("Add MMC Framework")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
|
|
https://source.denx.de/u-boot/custodians/u-boot-nand-flash
The first patch is by Weizhao Ouyang and avoids sf probe crashes.
The second patch is by Arseniy Krasnov and adds basic support for Amlogic
Meson NAND controller on AXG.
The following four patches are by Alexander Dahl and apply some fixes to
drivers/mtd/nand/raw/ and port some changes applied in Linux.
The following patch is by Bruce Suen and adds support for XTX SPINAND.
Finally, the last patch is again by Arseniy Krasnov and adds access to
OTP region, supporting info, dump, write and lock operations.
|
|
Add support for XTX XT26G0xA and XT26xxxD. The driver is ported from
linux-6.7.1. This driver is tested on Banana BPI-R3 with XT26G01A and
XT26G12D.
Link: https://lore.kernel.org/all/20240312014314.15454-1-bruce_suen@163.com
Signed-off-by: Bruce Suen <bruce_suen@163.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
|
|
Introduced with commit 6a8dfd57220d ("nand: atmel: Add DM based NAND
driver") when driver was initially ported from Linux. The context
around this and especially the code itself suggests 'read' is meant
instead of write.
The fix is the same as accepted in Linux already with mainline Linux
kernel commit 1c60e027ffde ("mtd: nand: raw: atmel: Fix comment in
timings preparation").
Link: https://lore.kernel.org/all/20240320090214.40465-6-ada@thorsis.com
Link: https://lore.kernel.org/linux-mtd/20240307172835.3453880-1-miquel.raynal@bootlin.com/T/#t
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
|
|
One tab in general. One tab plus two spaces for help text.
Link: https://lore.kernel.org/all/20240320090214.40465-4-ada@thorsis.com
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
|
|
Introduced in upstream Linux with commit 7a08dbaedd365 for release v5.0.
When the new atmel nand driver was backported to U-Boot with commit
6a8dfd57220d ("nand: atmel: Add DM based NAND driver") that definition
was added to the driver instead of the header file. Move it over to the
other definitions with the same help text it has in Linux.
Code actually using this has not been ported over to raw nand base yet.
Link: https://lore.kernel.org/all/20240320090214.40465-3-ada@thorsis.com
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
|
|
In every other place in this file the macro is used, make it consistent.
Link: https://lore.kernel.org/all/20240320090214.40465-2-ada@thorsis.com
Fixes: 9d1806fadc24 ("mtd: nand: Get rid of mtd variable in function calls")
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
|
|
Basic support for Amlogic Meson NAND controller on AXG. This version
works at only first EDO mode.
Based on Linux version 6.7.0-rc4.
Link: https://lore.kernel.org/all/20240210223927.570043-1-avkrasnov@salutedevices.com
Signed-off-by: Arseniy Krasnov <avkrasnov@salutedevices.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
|
|
Allowing multicast packets is required for IPv6 neighbor discovery
protocol.
Signed-off-by: Parvathi Bhogaraju <pbhogaraju@microsoft.com>
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
|
|
In IPv6 context, the ICMP and UDP checksum byte in the RX packet
is initially set to 0, recaclculated, and then re-inserted.
This process can result in a dirty cache line. To prevent issues,
it is essential to invalidate cache for the RX buffer before freeing
the descriptor for next DMA transfer.
This ensure that the dirty cache line doesn't inadvertently written back
due to cache eviction, there by corrupting the RX buffer
Signed-off-by: Parvathi Bhogaraju <pbhogaraju@microsoft.com>
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
|
|
Fix compilation warning:
../arch/arm/include/asm/io.h: In function 'eqos_free_pkt':
../arch/arm/include/asm/io.h:103:32: warning: 'rx_desc' may be used uninitialized [-Wmaybe-uninitialized]
103 | #define writel(v,c) ({ u32 __v = v; __iowmb(); __arch_putl(__v,c); __v; })
| ^~~
../drivers/net/dwc_eth_qos.c:1220:27: note: 'rx_desc' was declared here
1220 | struct eqos_desc *rx_desc;
| ^~~~~~~
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
MD Danish Anwar <danishanwar@ti.com> says:
Introduce ICSSG PRUETH support in uboot. The ICSSG driver is used in TI
AM654 SR2.0.
The ICSSG PRU Sub-system runs on EMAC firmware. This series Introduces
support for ICSSG driver in uboot.
This series has been tested on AM65x SR2.0, and the ICSSG interface is
able to ping / dhcp and boot kernel using tftp in uboot.
To use ICSSG2 ethernet, the ICSSG firmware needs to be loaded to PRU RPROC
cores and RPROC cores need to be booted with the firmware. This step is
done inside driver similar to kernel.
The remoteproc driver uses request_fw_into_buf() API from fs-loader driver
to load and start rproc with the required firmwares.
This series only introduces driver files. The device tree and config
changes to enable ICSSG driver will be introduced later.
|
|
ICSSG firmware supports FDB commands. Add support to send FDB commands
from driver. Once rx_flow_id is obtained from dma, let firmware know that
we are using this rx_flow_id by sending a FDB command.
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
|
|
This is the PRUSS Ethernet driver for TI AM654 SR2.0 and later SoCs with
the ICSSG PRU Sub-system running EMAC firmware. ICSSG Subsystem supports
two slices per instance. This driver caters to both slices / ports of
the icssg subsystem.
Since it is not possible for Ethernet driver to register more than one
port for a given instance, this patch introduces top level PRUETH as
UCLASS_MISC and binds UCLASS_ETH to individual ports in order to support
bringing up more than one Ethernet interface in U-Boot.
Since top level driver is UCLASS_MISC, board files would need to
instantiate the driver explicitly.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
|
|
Add icssg_queue.c file. This file introduces macros and APIs related to
ICSSG queues. These will be used by ICSSG Ethernet driver.
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
|
|
Add icssg_config.h / .c and icssg_classifier.c files. These are firmware
configuration and classification related files. Add MII helper APIs and
MACROs. These APIs and MACROs will be later used by ICSSG Ethernet driver.
Also introduce icssg_prueth.h which has definition of prueth related
structures.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
|
|
Add firmware interface related headers and macros for ICSSG Ethernet
driver. These macros will be later used by the ICSSG ethernet driver.
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
|
|
The sysreset TI-SCI API is available with TI-SCI always, there is no need
for a DT node to describe the availability of this. If the sysreset driver
is available then bind it during ti-sci probe.
Remove the unneeded device tree matching.
Signed-off-by: Andrew Davis <afd@ti.com>
Tested-by: Jonathan Humphreys <j-humphreys@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
|
|
The device name is a concatenation of the device node name of the cpsw
device and of the device node name of the port. In my case that is
ethernet@8000000
port@1
First the buffer is really too small, but more importantly, there is no
boundary check. Use snprintf() and increase the buffer size.
Fixes: 38922b1f4acc ("net: ti: am65-cpsw: Add support for multi port independent MAC mode")
Signed-off-by: Michael Walle <mwalle@kernel.org>
|
|
Simon Glass <sjg@chromium.org> says:
This little series reprises the EFI-video fix, fixes a USB problem and
enables a boot script for coreboot.
It also moves to truetype fonts for coreboot and qemu-x86, since the
menus look much better and there are no strong size constraints.
With these changes it is possible to boot a Linux distro automatically
with U-Boot on x86, including when U-Boot is the second-stage
bootloader.
|
|
This is needed to support Truetype fonts. In any case, the compiler
expects SSE to be available in 64-bit mode. Provide an option to enable
SSE so that hardware floating-point arithmetic works.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Suggested-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Saving and restoring entries is used for expo and for the command line,
which we don't use in SPL. Drop these methods.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
|
|
The ANSI codes are not correctly handled at present, in that the
requested X position is added to the current one.
Correct this and also call vidconsole_entry_start() to start a new text
line.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
|
|
This hunk of the patch was missed when using "b4" to apply the series.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Simon Glass <sjg@chromium.org> says:
This series is the culmanation of the current line of refactoring
series. It adjusts pxe to call the booting functionality directly
rather than going through the command-line interface.
With this is is possible to boot using the extlinux bootmeth without
the command line enabled.
It also updates fastboot to do a similar thing.
|
|
It is possible to boot a kernel without CMDLINE being enabled. Update
the implementation to handle this, and drop the condition from the
FASTBOOT config.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
|
|
Given the name of this variable, it should be an address, not a
pointer. Update this, to make it easier to use with sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Dmitrii Merkurev <dimorinny@google.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # on vim3
|
|
https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2024.07-rc1
xilinx:
- Do not call env_get_location when !ENV_IS_NOWHERE
- Add FDT_FIXUP_PARTITIONS support
- Fix legacy format MAC decoding
zynqmp:
- Enable semihosting SPL support
- DT updates
- Kconfig resort/cleanup
- Don't describe second image/capsule if !SPL
- Add support for dfu/capsule description via MTD
- Support JTAG as alternative boot mode
- Add support for TEG soc variant
zynqmp-kria:
- Wire usb4 boot device
- Update SDIO tristate pin configuration
- Disable SPI_FLASH_BAR to avoid issue with SPI after update
mbv:
- Enable SPL and binman
- Small platform changes
zynqmp-nand:
- Error out in case of unsupported SW ECC
- Clean error path
versal-net:
- Support multiple locations for variables
|
|
Missing line-feeds in error messages lead to output like:
phy_startup() failed: -110FAILED: -110=>
Output like the following is much easier to read:
phy_startup() failed: -110
FAILED: -110
=>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
|
|
There is no need to export goldfish_rtc_probe().
Fixes: 2d6dc19fd25d ("rtc: driver for Goldfish RTC")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
|
|
cpu_get_desc() for the RISC-V CPU currently reads "riscv,isa" to get
the description, but it is no longer a required property and cannot be
assummed to always be present, as the new "riscv,isa-extensions" and
"riscv,isa-base" properties may be present instead.
On RISC-V, cpu_get_desc() has two main uses - firstly providing an
informational name for the CPU for smbios or at boot with
DISPLAY_CPUINFO etc and secondly it forms the basis of ISA extension
detection in supports_extension() as it returns (a portion of) an ISA
string.
cpu_get_desc() returns a string, which aligned with "riscv,isa" but
the new property is a list of strings. Rather than add support for
the list of strings property, which would require creating an isa
string from "riscv,isa-extensions", modify the RISC-V CPU's
implementaion of cpu_get_desc() return the first compatible as the
cpu description instead. This may be fine for the informational cases,
but it would break extension dtection, given supports_extension()
expects cpu_get_desc() to return an ISA string.
Call dev_read_string() directly in supports_extension() to get the
contents of "riscv,isa" so that extension detection remains functional.
As a knock-on affect of this change, extension detection is no longer
broken for long ISA strings. Previously if the ISA string exceeded the
32 element array that supports_extension() passed to cpu_get_desc(),
it would return ENOSPC and no extensions would be detected.
This bug probably had no impact as U-Boot does not currently do anything
meaningful with the results of supports_extension() and most SoCs
supported by U-Boot don't have anywhere near that complex of an ISA
string. The QEMU virt machine's CPUs do however, so extension detection
doesn't work there.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
|
|
Add sdhci driver for cv1800b SoC.
Signed-off-by: Kongyang Liu <seashell11234455@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
|
|
https://source.denx.de/u-boot/custodians/u-boot-snapdragon
- Ethernet, i2c, and USB support are now enabled by default
- The clock driver gets some bug fixes and cleanup
- Invalid FDTs are now properly detected in board_fdt_blob_setup().
- The pinctrl driver gains preparatory support for per-pin function
muxes.
- Support is added for two generations of Qualcomm HighSpeed USB PHY
- A power domain driver is added for the Globall Distributed Switch
Controllers on the GCC hardware block.
- SDM845 gains USB host mode support.
- OF_LIVE is enabled by default for Qualcomm platforms
- Some U-Boot devicetree compatibility fixups are added during init to
improve compatbility with upstream DT.
|
|
- kirkwood: Switch to using upstream dts/dtsi files (Tony)
- mvebu: Turris Omnia - New board revision support (Marek)
|
|
|
|
Discovered while trying to use the second interface in the USB keyboard
driver necessary on Apple USB keyboards.
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Neal Gompa <neal@gompa.dev>
Signed-off-by: Janne Grunau <j@jannau.net>
|
|
The xhci driver currently only does the necessary initialization for
endpoints found in the first interface descriptor. Apple USB keyboards
(released 2021) use the second interface descriptor for the HID keyboard
boot protocol. To allow USB drivers to use endpoints from other
interface descriptors the xhci driver needs to ensure these endpoints
are initialized as well.
Use USB_MAX_ACTIVE_INTERFACES to control how many interface descriptors
are considered during endpoint initialisation.
For now define it to 2 as that is sufficient for supporting the Apple
keyboards.
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Neal Gompa <neal@gompa.dev>
Signed-off-by: Janne Grunau <j@jannau.net>
|
|
In the next step endpoints for multiple interfaces are set up. Move most
of the per endpoint initialization to separate function to avoid another
identation level.
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Neal Gompa <neal@gompa.dev>
Signed-off-by: Janne Grunau <j@jannau.net>
|
|
When using OF_LIVE, the debug UART driver won't be probed if it's a
subnode of the geni-se-qup controller. Add a NOP driver for the
controller to correctly discover its child nodes.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
The .direction_input and .direction_output ops are deprecated, and don't
seem to behave properly for us. Implement our own .set_flags op to
handle this correctly.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
Most devices only initialise the USB clocks for us if we boot via
"fastboot boot", add the missing clock configuration to get both USB
ports working regardless of the bootloader state.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
Define the GDSC power domains for SDM845.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
The RCG registers always have the same offsets, so only store the base
CMD register address and calculate the others relative to that.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
Some devices like the UART and clock controller reference an RPM(h)
power domain. We don't support this device in U-Boot, so add
DM_FLAG_DEFAULT_PD_CTRL_OFF to tell DM core not to try and enable the
power domain.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
Some Qualcomm SoCs newer than SDM845 feature a so-called "7nm phy"
driver, notable the SM8250 SoC which will gain U-Boot support in
upcoming patches.
Introduce a driver based on the Linux driver.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
[code cleanup, align symbol names with Linux, switch to clk/reset_bulk APIs]
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
The Snapdragon 845 and several other Qualcomm SoCs feature this
USB high-speed phy. Add a driver for it based on the Linux driver, with
support for the SDM845, and the QCM2290 and SM6115 SoCs which will gain
support in U-Boot in future patches.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
[code cleanup, switch to clk_bulk]
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
This patch is the preparation for SM8150 support. This new SoC
depending on the particular pin can have different numbers for the
same function. For example "rgmii" function for GPIO4 has id=2 while
for GPIO59 it has id=1. So, to support this type of SoCs,
get_function_mux() callback needs to know for which pin the function
is requested.
Signed-off-by: Volodymyr Babchuk <volodymyr_babchuk@epam.com>
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
