| Age | Commit message (Collapse) | Author |
|---|
|
The commit 2cc6cde647e2 ("mmc: rockchip_sdhci: Limit number of blocks
read in a single command") introduced a limit of number of blocks to
read to fix a Data End Bit Error on RK3568 and RK3588. This had a side
affect of significant slowing down reading FIT from eMMC.
After the commit 6de9d7b2f13c ("rockchip: rk35xx: Enable eMMC HS200 mode
by default") the limit of number of blocks to read workaround is no
longer necessary and at HS200+ a Data End Bit Error is no longer
happening using PIO mode.
Change this limitation to allow reading more than 4 blocks with a single
CMD18 command in PIO mode at HS200+ speed, keep using the 4 blocks
limitation when loadig FIT from eMMC at lower speed than HS200.
Fixes: 2cc6cde647e2 ("mmc: rockchip_sdhci: Limit number of blocks read in a single command")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
The SCLK_SFC can be set to a rate of 24, 50, 75, 100, 125 or 150 MHz.
However, clk_set_rate() will fail unless one of those exact rates are
used, and with newer and updated device tree files that contain
spi-max-frequency values that does not exactly match these rates use of
SPI flash may fail.
Fix this by using the highest possible rate that exceeds or is equal to
the requested rate.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
The REF_CLK_USB3OTGx clocks is used as reference clock for USB3 block.
Add simple support to get rate of REF_CLK_USB3OTGx clocks to fix
reference clock period configuration.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Acked-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
The CLK_USB3OTGx_REF clocks is used as reference clock for USB3 block.
Add simple support to get rate of CLK_USB3OTGx_REF clocks to fix
reference clock period configuration.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Acked-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Move cru_rk3308.h and grf_rk3308.h to arch-rockchip to match path used
for all other Rockchip SoCs.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Sync device tree from linux v6.8 and rename the rockchip,rk3308-mac
compatible in gmac_rockchip driver to match upstream linux.
Also move rk3308-roc-cc gmac node to u-boot.dtsi to not break features
not enabled in upstream device tree.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Add clkout_ctl and phy_sus regs to support USB2PHY for RK3308.
Based on linux commit 31f840e7ff3e ("phy: phy-rockchip-inno-usb2: add
support for RK3308 USB phy").
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Add dummy support for setting parent of USB480M clock.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Add support to get and set the SCLK_RTC32K clock rate.
Signed-off-by: Finley Xiao <finley.xiao@rock-chips.com>
[jonas@kwiboo.se: Update commit message]
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Support is added for 5 new Qualcomm SoCs:
* QCM2290 and SM6115 are low and mid range SoCs used on the RB1 and RB2
respectively. SM6115 is also used in some mid-range smartphones/tablets.
Initial support includes buttons and USB (host and gadget).
* SM8250 is a flagship SoC from 2020 used on the RB5, as well as many flagship
smartphones. The board can boot to a U-Boot prompt, but is missing regulators
necessary for USB support.
* SM8550, and SM8650 are flagship mobile SoCs from 2023 and 2024
respectively. Found on many high end smartphones.
In addition:
* Support is added for the Schneider HMIBSC board.
* mach-snapdragon switches to OF_UPSTREAM
* IPQ40xx gets several regressions fixed and some overall cleanup.
* The MSM serial driver gains the ability to generate the bit-clock
automatically, no longer relying on a custom DT property.
* The Qualcomm SMMU driver gets a generic compatible (so per-SoC compatibles
don't need to be added).
* Support for the GENI I2C controller is added.
* The qcom SPMI driver has SPMI v5 support fixed, and v7 support added.
* The qcom sdhci driver gets some fixes for SDCC v5 support.
* SDM845 gains sdcard support
* Support is added for the Synopsys eUSB2 PHY driver (used on SM8550 and SM8650)
* SYS_INIT_SP_BSS_OFFSET is set to 1.5M to give us more space for FDTs.
* RB2 gets a work-around to fix the USB dr_mode property before booting Linux.
|
|
Add Support for the Qualcomm Generic Interface (GENI) I2C interface
found on newer Qualcomm SoCs.
The Generic Interface (GENI) is a firmware based Qualcomm Universal
Peripherals (QUP) Serial Engine (SE) Wrapper which can support multiple
bus protocols depending on the firmware type loaded at early boot time
based on system configuration.
It also supports the "I2C Master Hub" which is a single function Wrapper
that only FIFO mode I2C.
It replaces the fixed-function QUP Wrapper found on older SoCs.
The geni-se.h containing the generic GENI Serial Engine registers defines
is imported from Linux.
Only FIFO mode is implemented, neither SE DMA nor GPI DMA are implemented.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
There is a clock associated with this phy, but it's always from the
rpmhcc and isn't actually needed for the hardware to work.
Drop all the clock handling from the driver.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
With the exception of SDM845, most other Qualcomm SoCs have the Qualcomm
specific (but not SoC) specific SMMU compatible string. Add it here so
we can match those without having to add individual SoCs to the list
here.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
This is used for the volume keys on some SM8150/SM8250 devices.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
As with some other modern PMICs, writing to the GPIOs seems to make the
device reset.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
Add the defines and support for SPMI arbiters version 7,
which can handle up to 1024 peripherals, and can also drive
a secondary bus which is not implemented yet.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Caleb Connolly <caleb.connolly@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
The cnfg registers provides the owner id for each peripheral,
so we can use this id to check if we're allowed to write register
to each peripherals.
Since the v5 can handle more peripherals, add the max_channels to
scan more starting from version 5, make the channel_map store
32bit values and introduce the SPMI_CHANNEL_READ_ONLY flag to
mark a peripheral as read-only.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Caleb Connolly <caleb.connolly@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
Since version 2, the cmd format has changed, takes helpers
from Linux driver and use a switch/case to handle all
versions in msm_spmi_write/read() command.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Caleb Connolly <caleb.connolly@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
Properly use ch_offset in msm_spmi_write() reg access.
Fixes: f5a2d6b4b03 ("spmi: msm: add arbiter version 5 support")
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Caleb Connolly <caleb.connolly@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
Add GPIO pinctrl function to enable driving GPIO pins as output low or
high.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
Add support for driving the GPIO pins as output low or high.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
SE HMIBSC board debug console requires RS232 flow control, so enable
corresponding support if RS232 gpios are present.
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
SE HMIBSC board uses UART1 as the main debug console, so add
corresponding clocks and pinmux support. Along with that update
instructions to enable clocks for debug UART support.
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
Currently, IPQ4019 pinctrl driver supports only a very limited number of
pin functions and is not fully DT compatible with Linux pinctrl nodes.
IPQ40xx SoC-s sometimes use different pin function numbers for the same
function depending on the pin number, so for example I2C0 on GPIO58 uses
function number 3 while on GPIO59 it uses function number 2.
So, in order to make the driver compatible with upstream DTS to avoid the
need to patch the pinctrl nodes in U-Boot and support all of the missing
pin functions lets rework the driver based on upstream Linux IPQ4019
pinctrl driver and the pending SM8150 U-Boot pinctrl driver which also uses
different function numbers pased on the exact pin number.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
If compiled with logging and debug UART support, the following is printed:
serial_msm serial@78af000: pinctrl_select_state_full: uclass_get_device_by_phandle_id: err=-19
This is due to the fact that IPQ4019 pinctrl driver is not available prior
to relocation and thus MSM serial will fail probing as pinctrl provider is
not available.
So, lets enable DM_FLAG_PRE_RELOC for IPQ4019 pinctrl to fix this.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
We want to use OF_UPSTREAM on IPQ40XX as its well supported upstream, so
as a preparation update pinctrl driver to look for the upstream pin format.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
IPQ4019 pinctrl driver was moved to the dedicated Qualcomm pinctrl
directory, but the KConfig depends on ARCH_SNAPDRAGON only and thus
PINCTRL_QCOM_IPQ4019 cannot be selected when ARCH_IPQ40XX is used.
Fixes: 24d2908e987a ("pinctrl: qcom: move ipq4019 driver from mach-ipq40xx")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
The driver currently requires the bit clock divider be hardcoded in
devicetree (or use the hardcoded default from apq8016).
The bit clock divider is used to derive the baud rate from the core
clock:
baudrate = clk_rate / csr_div
clk_rate is the actual programmed core clock rate which is returned by
clk_set_rate(), and this UART driver only supports a baudrate of 115200.
We can therefore determine the appropriate value for UARTDM_CSR by
iterating over the possible values and finding the one where the
equation above holds true for a baudrate of 115200.
Implement this logic and drop the non-standard DT bindings for this
driver.
Tested on dragonboard410c.
Tested-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
clk_set_rate() should return the clock rate that was set. The IPQ4019
clock driver doesn't set any rates yet but it should still return the
expected value so that drivers can work properly.
For a baud rate of 115200 with an expected bit clock divisor of 16, the
clock rate should be 1843200 so return that frequency.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
The clk_init_uart() helper always returns 0, but we're meant to return a
real clock rate. Given that we hardcode 115200 baud, just return the
clock rate that we set.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
MSM serial in DEBUG UART mode is trying to set .clk_rate, but the
msm_serial_data structure does not have such property at all, so lets
remove it as otherwise it will fail compiling.
Fixes: 90023bdfe979 ("serial: msm: add debug UART")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
Currently, DEBUG_UART_MSM depends on ARCH_SNAPDRAGON only, but IPQ40XX
devices also use the same UART HW so they can also use the debug UART.
So, allow selecting DEBUG_UART_MSM when using ARCH_IPQ40XX as well.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
The addresses were mistakenly swapped. Put them right.
Reported-by: Sumit Garg <sumit.garg@linaro.org>
Fixes: a737d8962cae ("mmc: msm_sdhci: correct vendor_spec_cap0 register for v5")
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
Add the GCC and TCSRCC clock driver for the SM8650 SoC.
The GCC driver uses the clk-qcom infrastructure to support GDSCs,
Resets and gates. While the TCSRCC is a simpler clock driver which
only supports gates.
The GCC enable and set_rate callbacks contains some tweaks to
setup clocks for Debug UART, SDCard controller and USB.
The TCSRCC gates returns the XO frequency, which is used by the
Synopsys eUSB2 driver to determine the PHY configuration.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
Add the GCC and TCSRCC clock driver for the SM8550 SoC.
The GCC driver uses the clk-qcom infrastructure to support GDSCs,
Resets and gates. While the TCSRCC is a simpler clock driver which
only supports gates.
The GCC enable and set_rate callbacks contains some tweaks to
setup clocks for Debug UART, SDCard controller and USB.
The TCSRCC gates returns the XO frequency, which is used by the
Synopsys eUSB2 driver to determine the PHY configuration.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
Adjust sdm845_get_pin_name() to return the correct names for the special
pins. This fixes a non-fatal -ENOSYS error when probing MMC.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
Allow setting the clock rate for the SD card core clock. This is
required for SD card support on SDM845 devices.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
We currently default to the lowest rate but this actually doesn't work
on most platforms. Default to the HS400 speed instead which is most
common on Qualcomm platforms.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
This is useful for debugging.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
using fdtdec_* functions is incompatible with OF_LIVE and generally
offers a less friendly interface. Update to use dev_read_* functions
instead.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
The V4 and V5 controllers have quite varied register layouts. Inherit
the register offsets and naming from the Linux driver. More version
specific offsets can be inherited from Linux as needed.
Fixes: 364c22a ("mmc: msm_sdhci: Add SDCC version 5.0.0 support")
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
Add a clock driver for the SM8250 SoC. This driver can enable necessary
clocks for UART, UFS, USB, and MMC.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
Add a driver for the clock controller in the SM6115 SoC, this is used in
the QRB4210 RB2 board.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
Add a clock driver for the QCM2290 SoC which is used in the QRB2210 RB1
board.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
Finally add the entries for the qcom,pmk8350-pwrkey and qcom,pmk8350-resin
found on PMICs used with SM8350 and later SoCs.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
Move node name checks to a proper data struct with all information
for the supported subnodes.
Replace the key offset defines with the Linux driver ones.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
Add support for PM8550 GPIO controller variant, keep read-only
until the GPIO and Pinctrl setup is fixed for new PMICs.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
This SoC features a pinctrl block with north, south, and west tiles
accessible to the AP.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
This SoC features a pinctrl block with west, east, and south tiles.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
This SoC has a basic pinctrl block with no tiles.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
