blob: ce4539a46f13a702a011f7a2be63e9ccd2c5d23d (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
|
.. SPDX-License-Identifier: GPL-2.0+
Milk-V Mars
===========
U-Boot for the Milk-V Mars uses the same U-Boot binaries as the VisionFive 2
board. In U-Boot SPL the actual board is detected and the device-tree patched
accordingly.
Building
--------
1. Add the RISC-V toolchain to your PATH.
2. Setup ARCH & cross compilation environment variable:
.. code-block:: none
export CROSS_COMPILE=<riscv64 toolchain prefix>
The M-mode software OpenSBI provides the supervisor binary interface (SBI) and
is responsible for the switch to S-Mode. It is a prerequisite to build U-Boot.
Support for the JH7110 was introduced in OpenSBI 1.2. It is recommended to use
a current release.
.. code-block:: console
git clone https://github.com/riscv/opensbi.git
cd opensbi
make PLATFORM=generic FW_TEXT_START=0x40000000 FW_OPTIONS=0
Now build the U-Boot SPL and U-Boot proper.
.. code-block:: console
cd <U-Boot-dir>
make starfive_visionfive2_defconfig
make OPENSBI=$(opensbi_dir)/build/platform/generic/firmware/fw_dynamic.bin
This will generate the U-Boot SPL image (spl/u-boot-spl.bin.normal.out) as well
as the FIT image (u-boot.itb) with OpenSBI and U-Boot.
Device-tree selection
---------------------
Depending on the board version U-Boot set variable $fdtfile to either
starfive/jh7110-starfive-visionfive-2-v1.2a.dtb or
starfive/jh7110-starfive-visionfive-2-v1.3b.dtb.
To overrule this selection the variable can be set manually and saved in the
environment
::
setenv fdtfile my_device-tree.dtb
env save
or the configuration variable CONFIG_DEFAULT_FDT_FILE can be used to set to
provide a default value.
Preparing the SD-Card
---------------------
The device firmware loads U-Boot SPL (u-boot-spl.bin.normal.out) from the
partition with type GUID 2E54B353-1271-4842-806F-E436D6AF6985. You are free
to choose any partition number.
With the default configuration U-Boot SPL loads the U-Boot FIT image
(u-boot.itb) from partition 2 (CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION=0x2).
When formatting it is recommended to use GUID
BC13C2FF-59E6-4262-A352-B275FD6F7172 for this partition.
The FIT image (u-boot.itb) is a combination of OpenSBI's fw_dynamic.bin,
u-boot-nodtb.bin and the device tree blob.
Format the SD card (make sure the disk has GPT, otherwise use gdisk to switch)
.. code-block:: bash
sudo sgdisk --clear \
--set-alignment=2 \
--new=1:4096:8191 --change-name=1:spl --typecode=1:2E54B353-1271-4842-806F-E436D6AF6985\
--new=2:8192:16383 --change-name=2:uboot --typecode=2:BC13C2FF-59E6-4262-A352-B275FD6F7172 \
--new=3:16384:1654784 --change-name=3:system --typecode=3:EBD0A0A2-B9E5-4433-87C0-68B6B72699C7 \
/dev/sdb
Copy U-Boot to the SD card
.. code-block:: bash
sudo dd if=u-boot-spl.bin.normal.out of=/dev/sdb1
sudo dd if=u-boot.itb of=/dev/sdb2
sudo mount /dev/sdb3 /mnt/
sudo cp u-boot-spl.bin.normal.out /mnt/
sudo cp u-boot.itb /mnt/
sudo cp Image.gz /mnt/
sudo cp initramfs.cpio.gz /mnt/
sudo cp jh7110-starfive-visionfive-2.dtb /mnt/
sudo umount /mnt
.. include:: jh7110_common.rst
|
