diff options
Diffstat (limited to 'include/linux/platform_data')
| -rw-r--r-- | include/linux/platform_data/dma-dw.h | 5 | ||||
| -rw-r--r-- | include/linux/platform_data/dma-mmp_tdma.h | 2 | ||||
| -rw-r--r-- | include/linux/platform_data/dma-s3c24xx.h | 6 | ||||
| -rw-r--r-- | include/linux/platform_data/gpio-htc-egpio.h | 57 | ||||
| -rw-r--r-- | include/linux/platform_data/gpio-lpc32xx.h | 50 | ||||
| -rw-r--r-- | include/linux/platform_data/macb.h | 6 | ||||
| -rw-r--r-- | include/linux/platform_data/mlxcpld-hotplug.h | 99 | ||||
| -rw-r--r-- | include/linux/platform_data/mtd-nand-s3c2410.h | 7 | ||||
| -rw-r--r-- | include/linux/platform_data/remoteproc-omap.h | 6 | ||||
| -rw-r--r-- | include/linux/platform_data/spi-s3c64xx.h | 3 | ||||
| -rw-r--r-- | include/linux/platform_data/usb-davinci.h | 23 |
11 files changed, 182 insertions, 82 deletions
diff --git a/include/linux/platform_data/dma-dw.h b/include/linux/platform_data/dma-dw.h index d15d8ba8cc24..e69e415d0d98 100644 --- a/include/linux/platform_data/dma-dw.h +++ b/include/linux/platform_data/dma-dw.h @@ -14,6 +14,7 @@ #include <linux/device.h> #define DW_DMA_MAX_NR_MASTERS 4 +#define DW_DMA_MAX_NR_CHANNELS 8 /** * struct dw_dma_slave - Controller-specific information about a slave @@ -23,6 +24,7 @@ * @dst_id: dst request line * @m_master: memory master for transfers on allocated channel * @p_master: peripheral master for transfers on allocated channel + * @hs_polarity:set active low polarity of handshake interface */ struct dw_dma_slave { struct device *dma_dev; @@ -30,6 +32,7 @@ struct dw_dma_slave { u8 dst_id; u8 m_master; u8 p_master; + bool hs_polarity; }; /** @@ -44,6 +47,7 @@ struct dw_dma_slave { * @nr_masters: Number of AHB masters supported by the controller * @data_width: Maximum data width supported by hardware per AHB master * (in bytes, power of 2) + * @multi_block: Multi block transfers supported by hardware per channel. */ struct dw_dma_platform_data { unsigned int nr_channels; @@ -58,6 +62,7 @@ struct dw_dma_platform_data { unsigned int block_size; unsigned char nr_masters; unsigned char data_width[DW_DMA_MAX_NR_MASTERS]; + unsigned char multi_block[DW_DMA_MAX_NR_CHANNELS]; }; #endif /* _PLATFORM_DATA_DMA_DW_H */ diff --git a/include/linux/platform_data/dma-mmp_tdma.h b/include/linux/platform_data/dma-mmp_tdma.h index 0c72886030ef..422d4504dbac 100644 --- a/include/linux/platform_data/dma-mmp_tdma.h +++ b/include/linux/platform_data/dma-mmp_tdma.h @@ -28,7 +28,7 @@ struct sram_platdata { int granularity; }; -#ifdef CONFIG_ARM +#ifdef CONFIG_MMP_SRAM extern struct gen_pool *sram_get_gpool(char *pool_name); #else static inline struct gen_pool *sram_get_gpool(char *pool_name) diff --git a/include/linux/platform_data/dma-s3c24xx.h b/include/linux/platform_data/dma-s3c24xx.h index 89ba1b0c90e4..4f9aba405e96 100644 --- a/include/linux/platform_data/dma-s3c24xx.h +++ b/include/linux/platform_data/dma-s3c24xx.h @@ -30,16 +30,22 @@ struct s3c24xx_dma_channel { u16 chansel; }; +struct dma_slave_map; + /** * struct s3c24xx_dma_platdata - platform specific settings * @num_phy_channels: number of physical channels * @channels: array of virtual channel descriptions * @num_channels: number of virtual channels + * @slave_map: dma slave map matching table + * @slavecnt: number of elements in slave_map */ struct s3c24xx_dma_platdata { int num_phy_channels; struct s3c24xx_dma_channel *channels; int num_channels; + const struct dma_slave_map *slave_map; + int slavecnt; }; struct dma_chan; diff --git a/include/linux/platform_data/gpio-htc-egpio.h b/include/linux/platform_data/gpio-htc-egpio.h new file mode 100644 index 000000000000..b4201c971367 --- /dev/null +++ b/include/linux/platform_data/gpio-htc-egpio.h @@ -0,0 +1,57 @@ +/* + * HTC simple EGPIO irq and gpio extender + */ + +#ifndef __HTC_EGPIO_H__ +#define __HTC_EGPIO_H__ + +#include <linux/gpio.h> + +/* Descriptive values for all-in or all-out htc_egpio_chip descriptors. */ +#define HTC_EGPIO_OUTPUT (~0) +#define HTC_EGPIO_INPUT 0 + +/** + * struct htc_egpio_chip - descriptor to create gpio_chip for register range + * @reg_start: index of first register + * @gpio_base: gpio number of first pin in this register range + * @num_gpios: number of gpios in this register range, max BITS_PER_LONG + * (number of registers = DIV_ROUND_UP(num_gpios, reg_width)) + * @direction: bitfield, '0' = input, '1' = output, + */ +struct htc_egpio_chip { + int reg_start; + int gpio_base; + int num_gpios; + unsigned long direction; + unsigned long initial_values; +}; + +/** + * struct htc_egpio_platform_data - description provided by the arch + * @irq_base: beginning of available IRQs (eg, IRQ_BOARD_START) + * @num_irqs: number of irqs + * @reg_width: number of bits per register, either 8 or 16 bit + * @bus_width: alignment of the registers, either 16 or 32 bit + * @invert_acks: set if chip requires writing '0' to ack an irq, instead of '1' + * @ack_register: location of the irq/ack register + * @chip: pointer to array of htc_egpio_chip descriptors + * @num_chips: number of egpio chip descriptors + */ +struct htc_egpio_platform_data { + int bus_width; + int reg_width; + + int irq_base; + int num_irqs; + int invert_acks; + int ack_register; + + struct htc_egpio_chip *chip; + int num_chips; +}; + +/* Determine the wakeup irq, to be called during early resume */ +extern int htc_egpio_get_wakeup_irq(struct device *dev); + +#endif diff --git a/include/linux/platform_data/gpio-lpc32xx.h b/include/linux/platform_data/gpio-lpc32xx.h deleted file mode 100644 index a544e962a818..000000000000 --- a/include/linux/platform_data/gpio-lpc32xx.h +++ /dev/null @@ -1,50 +0,0 @@ -/* - * Author: Kevin Wells <kevin.wells@nxp.com> - * - * Copyright (C) 2010 NXP Semiconductors - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - */ - -#ifndef __MACH_GPIO_LPC32XX_H -#define __MACH_GPIO_LPC32XX_H - -/* - * Note! - * Muxed GP pins need to be setup to the GP state in the board level - * code prior to using this driver. - * GPI pins : 28xP3 group - * GPO pins : 24xP3 group - * GPIO pins: 8xP0 group, 24xP1 group, 13xP2 group, 6xP3 group - */ - -#define LPC32XX_GPIO_P0_MAX 8 -#define LPC32XX_GPIO_P1_MAX 24 -#define LPC32XX_GPIO_P2_MAX 13 -#define LPC32XX_GPIO_P3_MAX 6 -#define LPC32XX_GPI_P3_MAX 29 -#define LPC32XX_GPO_P3_MAX 24 - -#define LPC32XX_GPIO_P0_GRP 0 -#define LPC32XX_GPIO_P1_GRP (LPC32XX_GPIO_P0_GRP + LPC32XX_GPIO_P0_MAX) -#define LPC32XX_GPIO_P2_GRP (LPC32XX_GPIO_P1_GRP + LPC32XX_GPIO_P1_MAX) -#define LPC32XX_GPIO_P3_GRP (LPC32XX_GPIO_P2_GRP + LPC32XX_GPIO_P2_MAX) -#define LPC32XX_GPI_P3_GRP (LPC32XX_GPIO_P3_GRP + LPC32XX_GPIO_P3_MAX) -#define LPC32XX_GPO_P3_GRP (LPC32XX_GPI_P3_GRP + LPC32XX_GPI_P3_MAX) - -/* - * A specific GPIO can be selected with this macro - * ie, GPIO_05 can be selected with LPC32XX_GPIO(LPC32XX_GPIO_P3_GRP, 5) - * See the LPC32x0 User's guide for GPIO group numbers - */ -#define LPC32XX_GPIO(x, y) ((x) + (y)) - -#endif /* __MACH_GPIO_LPC32XX_H */ diff --git a/include/linux/platform_data/macb.h b/include/linux/platform_data/macb.h index 21b15f6fee25..7815d50c26ff 100644 --- a/include/linux/platform_data/macb.h +++ b/include/linux/platform_data/macb.h @@ -8,6 +8,8 @@ #ifndef __MACB_PDATA_H__ #define __MACB_PDATA_H__ +#include <linux/clk.h> + /** * struct macb_platform_data - platform data for MACB Ethernet * @phy_mask: phy mask passed when register the MDIO bus @@ -15,12 +17,16 @@ * @phy_irq_pin: PHY IRQ * @is_rmii: using RMII interface? * @rev_eth_addr: reverse Ethernet address byte order + * @pclk: platform clock + * @hclk: AHB clock */ struct macb_platform_data { u32 phy_mask; int phy_irq_pin; u8 is_rmii; u8 rev_eth_addr; + struct clk *pclk; + struct clk *hclk; }; #endif /* __MACB_PDATA_H__ */ diff --git a/include/linux/platform_data/mlxcpld-hotplug.h b/include/linux/platform_data/mlxcpld-hotplug.h new file mode 100644 index 000000000000..e4cfcffaa6f4 --- /dev/null +++ b/include/linux/platform_data/mlxcpld-hotplug.h @@ -0,0 +1,99 @@ +/* + * include/linux/platform_data/mlxcpld-hotplug.h + * Copyright (c) 2016 Mellanox Technologies. All rights reserved. + * Copyright (c) 2016 Vadim Pasternak <vadimp@mellanox.com> + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions are met: + * + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in the + * documentation and/or other materials provided with the distribution. + * 3. Neither the names of the copyright holders nor the names of its + * contributors may be used to endorse or promote products derived from + * this software without specific prior written permission. + * + * Alternatively, this software may be distributed under the terms of the + * GNU General Public License ("GPL") version 2 as published by the Free + * Software Foundation. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + * ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE + * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR + * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF + * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS + * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN + * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) + * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + */ + +#ifndef __LINUX_PLATFORM_DATA_MLXCPLD_HOTPLUG_H +#define __LINUX_PLATFORM_DATA_MLXCPLD_HOTPLUG_H + +/** + * struct mlxcpld_hotplug_device - I2C device data: + * @adapter: I2C device adapter; + * @client: I2C device client; + * @brdinfo: device board information; + * @bus: I2C bus, where device is attached; + * + * Structure represents I2C hotplug device static data (board topology) and + * dynamic data (related kernel objects handles). + */ +struct mlxcpld_hotplug_device { + struct i2c_adapter *adapter; + struct i2c_client *client; + struct i2c_board_info brdinfo; + u16 bus; +}; + +/** + * struct mlxcpld_hotplug_platform_data - device platform data: + * @top_aggr_offset: offset of top aggregation interrupt register; + * @top_aggr_mask: top aggregation interrupt common mask; + * @top_aggr_psu_mask: top aggregation interrupt PSU mask; + * @psu_reg_offset: offset of PSU interrupt register; + * @psu_mask: PSU interrupt mask; + * @psu_count: number of equipped replaceable PSUs; + * @psu: pointer to PSU devices data array; + * @top_aggr_pwr_mask: top aggregation interrupt power mask; + * @pwr_reg_offset: offset of power interrupt register + * @pwr_mask: power interrupt mask; + * @pwr_count: number of power sources; + * @pwr: pointer to power devices data array; + * @top_aggr_fan_mask: top aggregation interrupt FAN mask; + * @fan_reg_offset: offset of FAN interrupt register; + * @fan_mask: FAN interrupt mask; + * @fan_count: number of equipped replaceable FANs; + * @fan: pointer to FAN devices data array; + * + * Structure represents board platform data, related to system hotplug events, + * like FAN, PSU, power cable insertion and removing. This data provides the + * number of hot-pluggable devices and hardware description for event handling. + */ +struct mlxcpld_hotplug_platform_data { + u16 top_aggr_offset; + u8 top_aggr_mask; + u8 top_aggr_psu_mask; + u16 psu_reg_offset; + u8 psu_mask; + u8 psu_count; + struct mlxcpld_hotplug_device *psu; + u8 top_aggr_pwr_mask; + u16 pwr_reg_offset; + u8 pwr_mask; + u8 pwr_count; + struct mlxcpld_hotplug_device *pwr; + u8 top_aggr_fan_mask; + u16 fan_reg_offset; + u8 fan_mask; + u8 fan_count; + struct mlxcpld_hotplug_device *fan; +}; + +#endif /* __LINUX_PLATFORM_DATA_MLXCPLD_HOTPLUG_H */ diff --git a/include/linux/platform_data/mtd-nand-s3c2410.h b/include/linux/platform_data/mtd-nand-s3c2410.h index c55e42ee57fa..f01659026b26 100644 --- a/include/linux/platform_data/mtd-nand-s3c2410.h +++ b/include/linux/platform_data/mtd-nand-s3c2410.h @@ -12,9 +12,10 @@ #ifndef __MTD_NAND_S3C2410_H #define __MTD_NAND_S3C2410_H +#include <linux/mtd/nand.h> + /** * struct s3c2410_nand_set - define a set of one or more nand chips - * @disable_ecc: Entirely disable ECC - Dangerous * @flash_bbt: Openmoko u-boot can create a Bad Block Table * Setting this flag will allow the kernel to * look for it at boot time and also skip the NAND @@ -31,7 +32,6 @@ * a warning at boot time. */ struct s3c2410_nand_set { - unsigned int disable_ecc:1; unsigned int flash_bbt:1; unsigned int options; @@ -40,6 +40,7 @@ struct s3c2410_nand_set { char *name; int *nr_map; struct mtd_partition *partitions; + struct device_node *of_node; }; struct s3c2410_platform_nand { @@ -51,6 +52,8 @@ struct s3c2410_platform_nand { unsigned int ignore_unset_ecc:1; + nand_ecc_modes_t ecc_mode; + int nr_sets; struct s3c2410_nand_set *sets; diff --git a/include/linux/platform_data/remoteproc-omap.h b/include/linux/platform_data/remoteproc-omap.h index bfbd12b41162..71a1b2399c48 100644 --- a/include/linux/platform_data/remoteproc-omap.h +++ b/include/linux/platform_data/remoteproc-omap.h @@ -39,9 +39,9 @@ struct omap_rproc_pdata { const char *firmware; const char *mbox_name; const struct rproc_ops *ops; - int (*device_enable) (struct platform_device *pdev); - int (*device_shutdown) (struct platform_device *pdev); - void(*set_bootaddr)(u32); + int (*device_enable)(struct platform_device *pdev); + int (*device_shutdown)(struct platform_device *pdev); + void (*set_bootaddr)(u32); }; #if defined(CONFIG_OMAP_REMOTEPROC) || defined(CONFIG_OMAP_REMOTEPROC_MODULE) diff --git a/include/linux/platform_data/spi-s3c64xx.h b/include/linux/platform_data/spi-s3c64xx.h index 5c1e21c87270..da79774078a7 100644 --- a/include/linux/platform_data/spi-s3c64xx.h +++ b/include/linux/platform_data/spi-s3c64xx.h @@ -40,9 +40,6 @@ struct s3c64xx_spi_info { int num_cs; bool no_cs; int (*cfg_gpio)(void); - dma_filter_fn filter; - void *dma_tx; - void *dma_rx; }; /** diff --git a/include/linux/platform_data/usb-davinci.h b/include/linux/platform_data/usb-davinci.h index e0bc4abe69c2..0926e99f2e8f 100644 --- a/include/linux/platform_data/usb-davinci.h +++ b/include/linux/platform_data/usb-davinci.h @@ -11,29 +11,6 @@ #ifndef __ASM_ARCH_USB_H #define __ASM_ARCH_USB_H -/* DA8xx CFGCHIP2 (USB 2.0 PHY Control) register bits */ -#define CFGCHIP2_PHYCLKGD (1 << 17) -#define CFGCHIP2_VBUSSENSE (1 << 16) -#define CFGCHIP2_RESET (1 << 15) -#define CFGCHIP2_OTGMODE (3 << 13) -#define CFGCHIP2_NO_OVERRIDE (0 << 13) -#define CFGCHIP2_FORCE_HOST (1 << 13) -#define CFGCHIP2_FORCE_DEVICE (2 << 13) -#define CFGCHIP2_FORCE_HOST_VBUS_LOW (3 << 13) -#define CFGCHIP2_USB1PHYCLKMUX (1 << 12) -#define CFGCHIP2_USB2PHYCLKMUX (1 << 11) -#define CFGCHIP2_PHYPWRDN (1 << 10) -#define CFGCHIP2_OTGPWRDN (1 << 9) -#define CFGCHIP2_DATPOL (1 << 8) -#define CFGCHIP2_USB1SUSPENDM (1 << 7) -#define CFGCHIP2_PHY_PLLON (1 << 6) /* override PLL suspend */ -#define CFGCHIP2_SESENDEN (1 << 5) /* Vsess_end comparator */ -#define CFGCHIP2_VBDTCTEN (1 << 4) /* Vbus comparator */ -#define CFGCHIP2_REFFREQ (0xf << 0) -#define CFGCHIP2_REFFREQ_12MHZ (1 << 0) -#define CFGCHIP2_REFFREQ_24MHZ (2 << 0) -#define CFGCHIP2_REFFREQ_48MHZ (3 << 0) - struct da8xx_ohci_root_hub; typedef void (*da8xx_ocic_handler_t)(struct da8xx_ohci_root_hub *hub, |