| Age | Commit message (Collapse) | Author |
|---|
|
Unevaluated properties are not allowed ('phy-addr' was unexpected)
socfpga_stratix10_swvp.dtb: sysmgr@ffd12000 (altr,sys-mgr-s10):
'interrupts' does not match any of the regexes:
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
The ECC manager entry for sdmmc should be a chip level entry, not a
board entry.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
Add spi-tx-bus-width and spi-rx-bus-width properties with value 4 to the
stratix10 device tree. This update configures the SPI controller to use a
4-bit bus width for both transmission and reception, potentially improving
SPI throughput and matching the hardware capabilities more closely.
Signed-off-by: Fong, Yan Kei <yan.kei.fong@altera.com>
Reviewed-by: Khairul Anuar Romli <khairul.anuar.romli@altera.com>
Reviewed-by: Matthew Gerlach <matthew.gerlach@altera.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
Add the clock-frequency property to the cb_intosc_ls_clk and
cb_intosc_hs_div2_clk device tree nodes.
The f2s_free_clk is implemented by custom logic in the FPGA; so it
should be disabled in the dtsi by default and enabled by a
dts for a specific FPGA design on a specific board.
Signed-off-by: Matthew Gerlach <matthew.gerlach@altera.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
This addresses this warning:
socfpga_stratix10_swvp.dtb: ethernet@ff800000 (altr,socfpga-stmmac-a10-s10):
'phy-addr' does not match any of the regexes: '^pinctrl-[0-9]+$'
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
The cpu1-start-addr property is only applicable to 32-bit SoCFPGA
platforms.
Removing this property will take care of warnings like this:
socfpga_stratix10_swvp.dtb: sysmgr@ffd12000: cpu1-start-addr:
False schema does not allow 4291846704
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
'altr,modrst-offset' property is not applicable for arm64 SoCFPGA
platforms.
This will fix this dtbs_check warning:
socfpga_stratix10_swvp.dtb:
rstmgr@ffd11000: altr,modrst-offset: False schema does not allow 32
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
Add the default "altr,rst-mgr" to the rstmgr node on Stratix10.
This fixes this warning:
arch/arm64/boot/dts/altera:33:10
rstmgr@ffd11000 (altr,stratix10-rst-mgr): compatible: 'oneOf' conditional
failed, one must be fixed:
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
Remove "snps,max-mtu" property which is both unused in the kernel and
undocumented. Most likely they are leftovers from downstream.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
This removes cacheinfo warnings at boot, e.g.:
cacheinfo: Unable to detect cache hierarchy for CPU 0
Signed-off-by: Beniamin Sandu <beniaminsandu@gmail.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
Flash node uses single "partition" node to describe partitions, so
remove deprecated address/size-cells properties to also fix dtc W=1
warnings:
socfpga_stratix10_socdk_nand.dts:171.10-200.4: Warning (avoid_unnecessary_addr_size): /soc@0/spi@ff8d2000/flash@0: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
Flash node uses single "partition" node to describe partitions, so
remove deprecated address/size-cells properties to also fix dtc W=1
warnings:
socfpga_stratix10_socdk.dts:182.10-211.4: Warning (avoid_unnecessary_addr_size): /soc@0/spi@ff8d2000/flash@0: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
The "arm,armv8-pmuv3" compatible is intended only for s/w models. Primarily,
it doesn't provide any detail on uarch specific events.
There's still remaining cases for CPUs without any corresponding PMU
definition and for big.LITTLE systems which only have a single PMU node
(there should be one per core type).
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Jisheng Zhang <jszhang@kernel.org>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Dinh Nguyen <dinguyen@kernel.org>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Bjorn Andersson <andersson@kernel.org>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Acked-by: Alim Akhtar <alim.akhtar@samsung.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Link: https://lore.kernel.org/r/20240417203853.3212103-1-robh@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
altr,dw-mshc-ciu-div and altr,dw-mshc-sdr-timing are neither documented
nor used by Linux, so remove them to fix dtbs_check warnings like:
socfpga_stratix10_swvp.dtb: mmc@ff808000: Unevaluated properties are not allowed
('altr,dw-mshc-ciu-div', 'altr,dw-mshc-sdr-timing' were unexpected)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
Bindings expect NAND child node name to match certain patterns:
socfpga_agilex_socdk_nand.dtb: nand-controller@ffb90000: Unevaluated properties are not allowed ('flash@0' was unexpected)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
The "soc" node has ranges with addresses, so it is should have unit
address to fix dtc W=1 warnings like:
socfpga_stratix10.dtsi:128.6-636.4: Warning (unit_address_vs_reg): /soc: node has a reg or ranges property, but no unit name
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
The "soc" node is supposed to have only MMIO children, so move the
firmware/svc node to top level to fix dtc W=1 warnings like:
socfpga_stratix10.dtsi:625.12-635.5: Warning (simple_bus_reg): /soc@0/firmware: missing or empty reg/ranges property
The node should still be instantiated by drivers/of/platform.c, just
like in all other platforms.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
The "soc" node is supposed to have only MMIO children, so move the FPGA
region node to top level to fix dtc W=1 warnings like:
socfpga_stratix10.dtsi:136.20-141.5: Warning (simple_bus_reg): /soc@0/base_fpga_region: missing or empty reg/ranges property
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
pinctrl-single bindings require pin configuration node names to match
certain patterns:
socfpga_stratix10_socdk.dtb: pinctrl@ffd13000: 'i2c1-pmx-func', 'i2c1-pmx-func-gpio'
do not match any of the regexes: '-pins(-[0-9]+)?$|-pin$', 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
The DWC2 USB bindings require clock-names property, to provide such to
fix warnings like:
socfpga_stratix10_swvp.dtb: usb@ffb40000: 'clock-names' is a required property
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
cdns,page-size and cdns,block-size are neither documented nor used by
Linux, so remove them to fix dtbs_check warnings like:
socfpga_n5x_socdk.dtb: flash@0: Unevaluated properties are not allowed ('cdns,block-size', 'cdns,page-size' were unexpected)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
Pull ARM devicetree updates from Arnd Bergmann:
"These are the devicetree updates for Arm and RISC-V based SoCs, mainly
from Qualcomm, NXP/Freescale, Aspeed, TI, Rockchips, Samsung, ST and
Starfive.
Only a few new SoC got added:
- TI AM62P5, a variant of the existing Sitara AM62x family
- Intel Agilex5, an FPGFA platform that includes an Cortex-A76/A55
SoC.
- Qualcomm ipq5018 is used in wireless access points
- Qualcomm SM4450 (Snapdragon 4 Gen 2) is a new low-end mobile phone
platform.
In total, 29 machines get added, which is low because of the summer
break. These cover SoCs from Aspeed, Broadcom, NXP, Samsung, ST,
Allwinner, Amlogic, Intel, Qualcomm, Rockchip, TI and T-Head. Most of
these are development and reference boards.
Despite not adding a lot of new machines, there are over 700 patches
in total, most of which are cleanups and minor fixes"
* tag 'soc-dt-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (735 commits)
arm64: dts: use capital "OR" for multiple licenses in SPDX
ARM: dts: use capital "OR" for multiple licenses in SPDX
arm64: dts: qcom: sdm845-db845c: Mark cont splash memory region as reserved
ARM: dts: qcom: apq8064: add support to gsbi4 uart
riscv: dts: change TH1520 files to dual license
riscv: dts: thead: add BeagleV Ahead board device tree
dt-bindings: riscv: Add BeagleV Ahead board compatibles
ARM: dts: stm32: add SCMI PMIC regulators on stm32mp135f-dk board
ARM: dts: stm32: STM32MP13x SoC exposes SCMI regulators
dt-bindings: rcc: stm32: add STM32MP13 SCMI regulators IDs
ARM: dts: stm32: support display on stm32f746-disco board
ARM: dts: stm32: rename mmc_vcard to vcc-3v3 on stm32f746-disco
ARM: dts: stm32: add pin map for LTDC on stm32f7
ARM: dts: stm32: add ltdc support on stm32f746 MCU
arm64: dts: qcom: sm6350: Hook up PDC as wakeup-parent of TLMM
arm64: dts: qcom: sdm670: Hook up PDC as wakeup-parent of TLMM
arm64: dts: qcom: sa8775p: Hook up PDC as wakeup-parent of TLMM
arm64: dts: qcom: sc8280xp: Hook up PDC as wakeup-parent of TLMM
arm64: dts: qcom: sdm670: Add PDC
riscv: dts: starfive: fix jh7110 qspi sort order
...
|
|
The "stmmaceth-ocp" reset line on the SoCFPGA stmmac ethernet driver is
the same as the "ahb" reset on a standard stmmac ethernet.
commit ("843f603762a5 dt-bindings: net: snps,dwmac: Add 'ahb'
reset/reset-name") documented the second reset signal as 'ahb' instead
of 'stmmaceth-ocp'. Change the reset-names of the SoCFPGA DWMAC driver to
'ahb'. In order not to break ABI, we will keep support in thedwmac-socfpga
driver to still make use of "stmmaceth-ocp".
This also fixes the dtbs_check warning:
ethernet@ff802000: reset-names:1: 'ahb' was expected
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
---
v2: update commit message to further describe the reason for the change
|
|
The correct dts property for the SCL falling time is
"i2c-scl-falling-time-ns".
Fixes: c8da1d15b8a4 ("arm64: dts: stratix10: i2c clock running out of spec")
Cc: stable@vger.kernel.org
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
flash@0: partitions: Unevaluated properties are not allowed
('partition@3FE0000' was unexpected)
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
Non-UBIFS related boot and fpga data should be stored in qspi_boot (mtd0)
while keeping the rootfs with UBIFS in the root partition "mtd1".
Thus, update the QSPI flash layout to support UBIFS in the mtd root
partition.
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@intel.com>
Signed-off-by: Kah Jing Lee <kah.jing.lee@intel.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
Although, we expect the bootloader to full memory details but passing empty
values can give warning, so add a default value.
memory: False schema does not allow {'device_type': ['memory'], 'reg': [[0, 0, 0, 0]]}
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
soc: usbphy@0: 'anyOf' conditional failed, one must be fixed:
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
sram@ffe00000: 'ranges' is a required property
sram@ffe00000: '#size-cells' is a required property
sram@ffe00000: '#address-cells' is a required property
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
Update the address-cells and size-cells to 2 in order to support 64-bit
addressing.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
Add the I2C pins definition to the Stratix10 devkit. This allows for the
I2C driver to use pinctrl on the pins to allow for GPIO recovery.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
---
v2: remove underscores in node names
|
|
The Stratix10/Agilex has a pin control IP that can make use of the
pinctrl-single driver.
Add the pinctrl-single dts property for the Stratix10/Agilex
platforms.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
---
v2: no changes
|
|
The node names should be generic and DT schema expects certain pattern:
altera/socfpga_stratix10_socdk.dtb: leds: 'hps0', 'hps1', 'hps2' do not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
The sdmmc controller's CIU(Card Interface Unit) clock's phase can be
adjusted through the register in the system manager. Add the binding
"altr,sysmgr-syscon" to the SDMMC node for the driver to access the
system manager. Add the "clk-phase-sd-hs" property in the SDMMC node to
designate the smpsel and drvsel properties for the CIU clock.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
The clocks are not part of the SoC but provided on the board
(external oscillators). Moving them out of soc node.
Signed-off-by: Niravkumar L Rabara <niravkumar.l.rabara@intel.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
Add Stratix 10 Software Virtual Platform device tree
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Teh Wen Ping <wen.ping.teh@intel.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
Fix whitespace coding style: use single space instead of tabs or
multiple spaces around '=' sign in property assignment. No functional
changes (same DTB).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
The pl330 DMA controller provides number of DMA channels and requests
through its registers, so duplicating this information (with a chance of
mistakes) in DTS is pointless. Additionally the DTS used always wrong
property names which causes DT schema check failures - the bindings
documented 'dma-channels' and 'dma-requests' properties without leading
hash sign.
Reported-by: Rob Herring <robh@kernel.org>
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220430121902.59895-4-krzysztof.kozlowski@linaro.org
|
|
USB DWC2 requires clock-names:
arm64/boot/dts/altera/socfpga_stratix10_socdk_nand.dt.yaml:
usb@ffb00000: 'clock-names' is a required property
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
Fixes dtbs_check warnings like:
pdma@ffda0000: $nodename:0: 'pdma@ffda0000' does not match '^dma-controller(@.*)?$'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
The devicetree specification requires that node name should be generic.
The dtschema complains if name does not match pattern, so make the
0.33 V regulator node name more generic.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
The Synopsys DW MSHC bindings require node name to be 'mmc':
dwmmc0@ff808000: $nodename:0: 'dwmmc0@ff808000' does not match '^mmc(@.*)?$'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
The ARM timer is usually considered not part of SoC node, just like
other ARM designed blocks (PMU, PSCI). This fixes dtbs_check warning:
arch/arm64/boot/dts/altera/socfpga_stratix10_socdk.dt.yaml: soc: timer:
{'compatible': ['arm,armv8-timer'], 'interrupts': [[1, 13, 3848], [1, 14, 3848], [1, 11, 3848], [1, 10, 3848]]} should not be valid under {'type': 'object'}
From schema: dtschema/schemas/simple-bus.yaml
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
The Altera SoCFPGA Stratix 10 SoC Development Kit is a board with
Stratix 10, so it needs its own compatible.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
Pull ARM SoC devicetree updates from Arnd Bergmann:
"As usual, this is the bulk of the updates for the SoC tree, adding
more devices to existing files, addressing issues from ever improving
automated checking, and fixing minor issues.
The most interesting bits as usual are the new platforms. All the
newly supported SoCs belong into existing families this time:
- Qualcomm gets support for two newly announced platforms, both of
which can now work in production environments: the SDX65 5G modem
that can run a minimal Linux on its Cortex-A7 core, and the
Snapdragon 8 Gen 1, their latest high-end phone SoC.
- Renesas adds support for R-Car S4-8, the most recent automotive
Server/Communication SoC.
- TI adds support for J721s2, a new automotive SoC in the K3 family.
- Mediatek MT7986a/b is a SoC used in Wifi routers, the latest
generation following their popular MT76xx series. Only basic
support is added for now.
- NXP i.MX8 ULP8 is a new low-power variant of the widespread i.MX8
series.
- TI SPEAr320s is a minor variant of the old SPEAr320 SoC that we
have supported for a long time.
New boards with the existing SoCs include
- Aspeed AST2500/AST2600 BMCs in TYAN, Facebook and Yadro servers
- AT91/SAMA5 based evaluation board
- NXP gains twenty new development and industrial boards for their
i.MX and Layerscape SoCs
- Intel IXP4xx now supports the final two machines in device tree
that were previously only supported in old style board files.
- Mediatek MT6589 is used in the Fairphone FP1 phone from 2013, while
MT8183 is used in the Acer Chromebook 314.
- Qualcomm gains support for the reference machines using the two new
SoCs, plus a number of Chromebook variants and phones based on the
Snapdragon 7c, 845 and 888 SoCs, including various Sony Xperia
devices and the Microsoft Surface Duo 2.
- ST STM32 now supports the Engicam i.Core STM32MP1 carrier board.
- Tegra now boots various older Android devices based on 32-bit chips
out of the box, including a number of ASUS Transformer tablets.
There is also a new Jetson AGX Orin developer kit.
- Apple support adds the missing device trees for all the remaining
M1 Macbook and iMac variants, though not yet the M1 Pro/Max
versions.
- Allwinner now supports another version of the Tanix TX6 set-top box
based on the H6 SoC.
- Broadcom gains support for the Netgear RAXE500 Wireless router
based on BCM4908"
* tag 'dt-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (574 commits)
Revert "ARM: dts: BCM5301X: define RTL8365MB switch on Asus RT-AC88U"
arm64: dts: qcom: sm6125: Avoid using missing SM6125_VDDCX
arm64: dts: qcom: sm8450-qrd: Enable USB nodes
arm64: dts: qcom: sm8450: Add usb nodes
ARM: dts: aspeed: add LCLK setting into LPC KCS nodes
dt-bindings: ipmi: bt-bmc: add 'clocks' as a required property
ARM: dts: aspeed: add LCLK setting into LPC IBT node
ARM: dts: aspeed: p10: Add TPM device
ARM: dts: aspeed: p10: Enable USB host ports
ARM: dts: aspeed: Add TYAN S8036 BMC machine
ARM: dts: aspeed: tyan-s7106: Add uart_routing and fix vuart config
ARM: dts: aspeed: Adding Facebook Bletchley BMC
ARM: dts: aspeed: g220a: Enable secondary flash
ARM: dts: Add openbmc-flash-layout-64-alt.dtsi
ARM: dts: aspeed: Add secure boot controller node
dt-bindings: aspeed: Add Secure Boot Controller bindings
ARM: dts: Remove "spidev" nodes
dt-bindings: pinctrl: samsung: Add pin drive definitions for Exynos850
dt-bindings: arm: samsung: Document E850-96 board binding
dt-bindings: Add vendor prefix for WinLink
...
|
|
Because of commit 9cb2ff111712 ("spi: cadence-quadspi: Disable Auto-HW polling"),
which does a write to the CQSPI_REG_WR_COMPLETION_CTRL register
regardless of any condition. Well, the Cadence QuadSPI controller on
Intel's SoCFPGA platforms does not implement the
CQSPI_REG_WR_COMPLETION_CTRL register, thus a write to this register
results in a crash!
So starting with v5.16, I introduced the patch
98d948eb833 ("spi: cadence-quadspi: fix write completion support"),
which adds the dts compatible "intel,socfpga-qspi" that is specific for
versions that doesn't have the CQSPI_REG_WR_COMPLETION_CTRL register implemented.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
---
v3: revert back to "intel,socfpga-qspi"
v2: use both "cdns,qspi-nor" and "cdns,qspi-nor-0010"
|
|
Change NAND flash MTD partition in device tree after implementation of
UBI and UBIFS. "u-boot" partition remain for raw u-boot image, but "root"
partition is use for UBI image containing all other components.
Signed-off-by: Sin Hui Kho <sin.hui.kho@intel.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
Simplify 32-bit and 64-bit Intel SoCFPGA Kconfig options by having only
one for both of them. This the common practice for other platforms.
Additionally, the ARCH_SOCFPGA is too generic as SoCFPGA designs come
from multiple vendors.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
This is to remove similar errors as below:
OF: /.../gpio-port@0: could not find phandle
Commit 7569486d79ae ("gpio: dwapb: Add ngpios DT-property support")
explained the reason of above errors well and added the generic
"ngpios" property, let's use it.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
The QSPI flash node needs to have the required "jedec,spi-nor"
in the compatible string.
Fixes: 0cb140d07fc7 ("arm64: dts: stratix10: Add QSPI support for Stratix10")
Cc: stable@vger.kernel.org
Suggested-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
