| Age | Commit message (Collapse) | Author |
|---|
|
https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux into soc/newsoc
Initial Anlogic Platform Support
Add bindings for the serial and timer peripherals, and a basic soc dtsi
for the Anlogic dr1v90 SoC. The Milianke MLKPAI FS01 is the first board
for this SoC. Add myself as maintainer for this platform for the time
being.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
* tag 'anlogic-initial-6.19-v2' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux:
MAINTAINERS: Setup support for Anlogic tree
riscv: defconfig: Enable Anlogic SoC
riscv: dts: anlogic: Add Milianke MLKPAI FS01 board
riscv: dts: Add initial Anlogic DR1V90 SoC device tree
riscv: Add Anlogic SoC famly Kconfig support
dt-bindings: serial: snps-dw-apb-uart: Add Anlogic DR1V90 uart
dt-bindings: timer: Add Anlogic DR1V90 ACLINT MTIMER
dt-bindings: riscv: Add Anlogic DR1V90
dt-bindings: riscv: Add Nuclei UX900 compatibles
dt-bindings: vendor-prefixes: Add Anlogic, Milianke and Nuclei
|
|
Add support for the Milianke MLKPAI FS01 board based on the Anlogic
DR1V90 SoC. The board features 512MB of onboard memory, USB-C UART, 1GbE
RJ45 Ethernet, USB-A 2.0 port, TF card slot, and 256Mbit Quad-SPI flash.
Currently, the board can boot to a console via UART1, which is connected
to the onboard serial chip and routed to the Type-C interface.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Junhui Liu <junhui.liu@pigmoral.tech>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
Add device tree source describing the Tenstorrent Blackhole SoC and the
Blackhole P100 and P150 PCIe cards. There are no differences between
the P100 and P150 cards from the perspective of an OS kernel like Linux
running on the X280 cores.
There is a virtual UART implemented in OpenSBI firmware that allows a
console program on the PCIe host to communicate through shared memory
with Linux running on the Blackhole card. CONFIG_HVC_RISCV_SBI needs to
be enabled. The boot script on the host adds 'console=hvc0' so that the
full boot output appears in the console program on the host.
Link: https://github.com/tenstorrent/opensbi/
Link: https://github.com/tenstorrent/tt-bh-linux
Reviewed-by: Joel Stanley <jms@oss.tenstorrent.com>
Signed-off-by: Drew Fustini <dfustini@oss.tenstorrent.com>
|
|
Add minimal device tree for HiFive Premier P550 Development board
Currently the data populated in this DT file is for UART.
Signed-off-by: Min Lin <linmin@eswincomputing.com>
Co-developed-by: Pinkesh Vaghela <pinkesh.vaghela@einfochips.com>
Signed-off-by: Pinkesh Vaghela <pinkesh.vaghela@einfochips.com>
Tested-by: Samuel Holland <samuel.holland@sifive.com>
Tested-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
Reviewed-by: Samuel Holland <samuel.holland@sifive.com>
Link: https://lore.kernel.org/r/20250825132427.1618089-7-pinkesh.vaghela@einfochips.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Introduce the device tree support for Voyager development board.
Currently only support booting into console with only uart,
other features will be added later.
Signed-off-by: Ben Zong-You Xie <ben717@andestech.com>
Link: https://lore.kernel.org/r/20250711133025.2192404-8-ben717@andestech.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Commit 654102df2ac2 ("kbuild: add generic support for built-in boot
DTBs") introduced generic support for built-in DTBs.
Select GENERIC_BUILTIN_DTB when built-in DTB support is enabled.
To keep consistency across architectures, this commit also renames
CONFIG_BUILTIN_DTB_SOURCE to CONFIG_BUILTIN_DTB_NAME.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20241222000836.2578171-1-masahiroy@kernel.org
Signed-off-by: Alexandre Ghiti <alexghiti@rivosinc.com>
|
|
Banana Pi BPI-F3 [1] is a industrial grade RISC-V development board, it
design with SpacemiT K1 8 core RISC-V chip [2].
Currently only support booting into console with only uart enabled,
other features will be added soon later.
Link: https://docs.banana-pi.org/en/BPI-F3/BananaPi_BPI-F3 [1]
Link: https://www.spacemit.com/en/spacemit-key-stone-2/ [2]
Signed-off-by: Yangyu Chen <cyy@cyyself.name>
Acked-by: Jesse Taube <jesse@rivosinc.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Yixun Lan <dlan@gentoo.org>
|
|
The BUILTIN_DTB_SOURCE was only configured for K210 before. Since
SOC_BUILTIN_DTB_DECLARE was removed at commit d5805af9fe9f ("riscv: Fix
builtin DTB handling") from patch [1], the kernel cannot choose one of the
dtbs from then on and always take the first one dtb to use. Then, another
commit 0ddd7eaffa64 ("riscv: Fix BUILTIN_DTB for sifive and microchip soc")
from patch [2] supports BUILTIN_DTB_SOURCE for other SoCs. However, this
feature will only work if the Kconfig we use links the dtb we expected in
the first place as mentioned in the thread [3]. Thus, a config
BUILTIN_DTB_SOURCE is needed for all SoCs to choose one dtb to use.
For some considerations, this patch also removes default y if XIP_KERNEL
for BUILTIN_DTB, as this requires setting a proper dtb to use on the
BUILTIN_DTB_SOURCE, else the kernel with XIP but does not set
BUILTIN_DTB_SOURCE or unselect BUILTIN_DTB will not boot.
Also, this patch removes the default dtb string for k210 from Kconfig to
nommu_k210_defconfig and nommu_k210_sdcard_defconfig to avoid complex
Kconfig settings for other SoCs in the future.
[1] https://lore.kernel.org/linux-riscv/20201208073355.40828-5-damien.lemoal@wdc.com/
[2] https://lore.kernel.org/linux-riscv/20210604120639.1447869-1-alex@ghiti.fr/
[3] https://lore.kernel.org/linux-riscv/CAK7LNATt_56mO2Le4v4EnPnAfd3gC8S_Sm5-GCsfa=qXy=8Lrg@mail.gmail.com/
Signed-off-by: Yangyu Chen <cyy@cyyself.name>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
Milk-V Pioneer [1] is a developer motherboard based on SG2042
in a standard mATX form factor.
Currently only support booting into console with only uart
enabled, other features will be added soon later.
Link: https://milkv.io/pioneer [1]
Reviewed-by: Guo Ren <guoren@kernel.org>
Acked-by: Chao Wei <chao.wei@sophgo.com>
Signed-off-by: Chen Wang <unicorn_wang@outlook.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
New additions to the list have tried to respect alphanumeric ordering,
but the thing was out of order to start with. Sort it.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
Sipeed's Lichee Pi 4A development board uses Lichee Module 4A core
module which is powered by T-HEAD's TH1520 SoC. Add minimal device
tree files for the core module and the development board.
Support basic uart/gpio/dmac drivers, so supports booting to a basic
shell.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
The MangoPi MQ is a tiny SBC built around the Allwinner D1s. Its
onboard peripherals include two USB Type-C ports (1 device, 1 host)
and RTL8189FTV WLAN.
A MangoPi MQ-R variant of the board also exists. The MQ-R has a
different form factor, but the onboard peripherals are the same.
Most D1 and D1s boards use a similar power tree, with the 1.8V rail
powered by the SoC's internal LDOA, analog domains powered by ALDO,
and the rest of the board powered by always-on fixed regulators. To
avoid duplication, factor out the regulator information that is
common across boards.
The board also exposes GPIO Port E via a FPC connector, which can
support either a camera or an RMII Ethernet PHY. The additional
regulators supply that connector.
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Reviewed-by: Guo Ren <guoren@kernel.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230126045738.47903-6-samuel@sholland.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
|
|
Convert all non user visible use of SOC_FOO symbols to their ARCH_FOO
variants. The canaan DTs are an outlier in that they're gated at the
directory and the file level. Drop the directory level gating while we
are swapping the symbol names over.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
Enable the minimal blocks required for booting the Renesas RZ/Five
SMARC EVK with initramfs.
Below are the blocks which are enabled:
- CPG
- CPU0
- DDR (memory regions)
- PINCTRL
- PLIC
- SCIF0
As we are reusing the RZ/G2UL SoC base DTSI [0], RZ/G2UL SMARC SoM [1] and
carrier [2] board DTSIs which enables almost all the blocks supported
by the RZ/G2UL SMARC EVK and whereas on RZ/Five SoC we will be gradually
enabling the blocks hence the aliases for ETH/I2C are deleted and rest
of the IP blocks are marked as disabled/deleted.
[0] arch/arm64/boot/dts/renesas/r9a07g043.dtsi
[1] arch/arm64/boot/dts/renesas/rzg2ul-smarc-som.dtsi
[2] arch/arm64/boot/dts/renesas/rzg2ul-smarc.dtsi
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Link: https://lore.kernel.org/r/20221028165921.94487-6-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add initial device tree for the BeagleV Starlight Beta board. About 300
of these boards were sent out as part of a now cancelled BeagleBoard.org
project.
I2C timing data is based on the device tree in the vendor u-boot port.
Heartbeat LED added by Geert.
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Co-developed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
|
|
Add initial DTS for Microchip ICICLE board having only
essential devices (clocks, sdhci, ethernet, serial, etc).
The device tree is based on the U-Boot patch.
https://patchwork.ozlabs.org/project/uboot/patch/20201110103414.10142-6-padmarao.begari@microchip.com/
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
|
|
Rename configuration options and directories related to the Kendryte
K210 SoC to use the SoC vendor name (canaan) instead of the "kendryte"
branding name.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
|
|
All SiPeed K210 MAIX boards have the exact same vendor, arch and
implementation IDs, preventing differentiation to select the correct
device tree to use through the SOC_BUILTIN_DTB_DECLARE() macro. This
result in this macro to be useless and mandates changing the code of
the sysctl driver to change the builtin device tree suitable for the
target board.
Fix this problem by removing the SOC_BUILTIN_DTB_DECLARE() macro since
it is used only for the K210 support. The code searching the builtin
DTBs using the vendor, arch an implementation IDs is also removed.
Support for builtin DTB falls back to the simpler and more traditional
handling of builtin DTB using the CONFIG_BUILTIN_DTB option, similarly
to other architectures.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
|
|
The K210's bootloader does not provide a device tree. Give the ability
to providea builtin one with the SOC_KENDRYTE_K210_BUILTIN_DTB option.
If selected, this option result in the definition of a builtin DTB
entry in the k210 sysctl driver.
If defined, the builtin DTB entry points to the default k210.dts device
tree file and is keyed with the vendor ID 0x4B5, the arch ID
0xE59889E6A5A04149 ("Canaan AI" in UTF-8 coded Chinese) and the impl ID
0x4D41495832303030 ("MAIX200"). These values are reported by the SiPEED
MAIXDUINO board, the SiPEED MAIX Go board and the SiPEED Dan Dock board.
[Thanks to Damien for the K210 IDs]
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
|
|
Add a generic device tree for Kendryte K210 SoC based boards. This is
for now a very simple device tree describing the core elements of the
SoC. This is suitable (and tested) for the Kendryte KD233 development
board, the Sipeed MAIX M1 Dan Dock board and the Sipeed MAIXDUINO board.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
|
|
Similar to ARM64, add support for building DTB files from DT source
data for RISC-V boards.
This patch starts with the infrastructure needed for SiFive boards.
Boards from other vendors would add support here in a similar form.
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Loys Ollivier <lollivier@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
|
