| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This is entirely SoC clk drivers.
The majority diff wise is for the new Rockchip and Qualcomm clk
drivers which is mostly lines and lines of data structures to describe
the clk hardware in these SoCs. Beyond those two, Renesas continues to
incrementally add clks to their SoC drivers, causing them to show up
higher in the diffstat this time because they added quite a few clks
all over the place.
Overall it is a semi-quiet release that has some new clk drivers and
the usual fixes for clock data that was wrong or missing and
non-critical cleanups that plug error paths or fix typos.
New Drivers:
- Qualcomm IPQ5424 Network Subsystem Clock Controller
- Qualcomm SM8750 Video Clock Controller
- Rockchip RV1126B and RK3506 clock drivers
- i.MX8ULP SIM LPAV clock driver
- Samsung ACPM (firmware interface) clock driver
- Altera Agilex5 clock driver"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (117 commits)
clk: keystone: fix compile testing
clk: keystone: syscon-clk: fix regmap leak on probe failure
clk: qcom: Mark camcc_sm7150_hws static
clk: samsung: exynos-clkout: Assign .num before accessing .hws
clk: rockchip: Add clock and reset driver for RK3506
dt-bindings: clock: rockchip: Add RK3506 clock and reset unit
clk: actions: Fix discarding const qualifier by 'container_of' macro
clk: spacemit: Set clk_hw_onecell_data::num before using flex array
clk: visconti: Add VIIF clocks
dt-bindings: clock: tmpv770x: Add VIIF clocks
dt-bindings: clock: tmpv770x: Remove definition of number of clocks
clk: visconti: Do not define number of clocks in bindings
clk: rockchip: Add clock controller for the RV1126B
dt-bindings: clock, reset: Add support for rv1126b
clk: rockchip: Implement rockchip_clk_register_armclk_multi_pll()
clk: qcom: x1e80100-dispcc: Add USB4 router link resets
dt-bindings: clock: qcom: x1e80100-dispcc: Add USB4 router link resets
clk: qcom: videocc-sm8750: Add video clock controller driver for SM8750
dt-bindings: clock: qcom: Add SM8750 video clock controller
clk: qcom: branch: Extend invert logic for branch2 mem clocks
...
|
|
Use the FIELD_{GET,PREP}() and field_{get,prep}() helpers for const
respective non-const bitfields, instead of open-coding the same
operations.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Yury Norov (NVIDIA) <yury.norov@gmail.com>
|
|
The Renesas RZ/T2H (R9A09G077) and RZ/N2H (R9A09G087) SoCs have four SPI
peripherals, each with their own clock divider, which divides PLL4 by
either 24, 25, 30 or 32, similar to the SCI peripheral.
The dividers feed into the usual module clocks.
Add them all.
Signed-off-by: Cosmin Tanislav <cosmin-gabriel.tanislav.xa@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20251105104151.1489281-2-cosmin-gabriel.tanislav.xa@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add USB3.0 clock and reset entries.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20251101050034.738807-5-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add USB3.0 clock and reset entries.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20251101050034.738807-4-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add RSCI clock and reset entries.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20251027154615.115759-2-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
The current code uses of_iomap() to map registers but never calls
iounmap() on any error path after the mapping. This causes a memory
leak when probe fails after successful ioremap, for example when
of_clk_add_provider() or r9a06g032_add_clk_domain() fails.
Replace of_iomap() with devm_of_iomap() to automatically unmap the
region on probe failure. Update the error check accordingly to use
IS_ERR() and PTR_ERR() since devm_of_iomap() returns ERR_PTR on error.
Fixes: 4c3d88526eba ("clk: renesas: Renesas R9A06G032 clock driver")
Signed-off-by: Haotian Zhang <vulab@iscas.ac.cn>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20251030061603.1954-1-vulab@iscas.ac.cn
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Convert the divider clock registration in the R9A09G077 CPG driver to use
device-managed (devm_) helper functions.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20251028165127.991351-4-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Remove an unnecessary blank line at the end of
r9a09g077_cpg_div_clk_register() to tidy up the code.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20251028165127.991351-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add the CLK_SET_RATE_PARENT flag to divider clock registration so that rate
changes can propagate to parent clocks when needed. This allows the CPG
divider clocks to request rate adjustments from their parent, ensuring
correct frequency scaling and improved flexibility in clock rate selection.
Fixes: 065fe720eec6e ("clk: renesas: Add support for R9A09G077 SoC")
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20251028165127.991351-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Describe the 3DGE module clock needed to operate the PowerVR GPU.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20251106211604.2766465-5-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Describe the ZG Core clock needed to operate the PowerVR GPU.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20251106211604.2766465-4-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
The FRQCRB register on R-Car V3U, V4H and V4M do in addition to the
already supported KICK bit contain settings for the frequency division
ratios for the clocks ZTR, ZT, ZS and ZG. It is however not possible to
use the latter when registering a Z clock with the DEF_GEN4_Z() macro.
This change adds support for that by extending the existing practice of
treating the bit field offsets at multiples of 32 to map to a different
register. With this new mapping in palace
bit offsets 0 - 31 map to FRQCRC0
bit offsets 32 - 63 map to FRQCRC1
bit offsets 64 - 95 map to FRQCRB
The change also adds an error condition to return an error if an unknown
offset is used.
The KICK bit defined in FRQCRB and already supported covers all three
registers and no addition to how it is handled are needed.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20251106211604.2766465-3-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add entries detailing the clocks and resets for the ISP in the
RZ/V2N SoC.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20251023210724.666476-4-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add support for the PLLVDO clock and its related CRU clocks and reset
entries in the R9A09G056 CPG driver. Introduce `CLK_PLLVDO` and associated
clocks like `CLK_PLLVDO_CRU0` and `CLK_PLLVDO_CRU1`, along with their
corresponding dividers.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20251023210724.666476-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add clock and reset definitions required to support the DSI and LCDC
hardware blocks on the RZ/V2N SoC. This includes new core clocks, clock
dividers, module clocks, and reset entries, as well as PLL and divider
configurations specific to these peripherals.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20251023210724.666476-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
The Renesas RZ/T2H (R9A09G077) and RZ/N2H (R9A09G087) SoCs have a TSU
peripheral which is controlled by a module clock.
The TSU module clock is enabled in register MSTPCRD (0x30c), at bit 7,
resulting in a (0x30c - 0x300) / 4 * 100 + 7 = 307 index.
Add it to the list of module clocks.
Signed-off-by: Cosmin Tanislav <cosmin-gabriel.tanislav.xa@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20251023081925.2412325-2-cosmin-gabriel.tanislav.xa@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add clock and reset entries for the DSI and LCDC peripherals.
Co-developed-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com>
Signed-off-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20251015192611.241920-5-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
clk: renesas: rzv2h: Add support for DSI clocks
RZ/V2H Clock Pulse Generator PLLDSI API, shared by clock and MIPI DSI
driver source files.
|
|
Add support for PLLDSI and its post-dividers in the RZ/V2H CPG driver and
export helper APIs for use by the DSI driver.
Introduce per-PLL-DSI state in the CPG private structure and provide a
set of helper functions that find valid PLL parameter combinations for
a requested frequency. The new helpers are rzv2h_get_pll_pars(),
rzv2h_get_pll_div_pars(), rzv2h_get_pll_divs_pars() and
rzv2h_get_pll_dtable_pars() and they are exported in the "RZV2H_CPG"
namespace for use by other consumers (notably the DSI driver). These
helpers perform iterative searches over PLL parameters (M, K, P, S)
and optional post-dividers and return the best match (or an exact
match when possible).
Move PLL/CLK related limits and parameter types into the shared
include (include/linux/clk/renesas.h) by adding struct rzv2h_pll_limits,
struct rzv2h_pll_pars and struct rzv2h_pll_div_pars plus the
RZV2H_CPG_PLL_DSI_LIMITS() helper macro to define DSI PLL limits.
This change centralises the PLLDSI algorithms so the CPG and DSI
drivers compute PLL parameters consistently and allows the DSI driver
to accurately request rates and program its PLL.
Co-developed-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com>
Signed-off-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20251015192611.241920-4-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Replace the older FIELD_GET-wrapping helper macros with plain GENMASK
definitions for the PLL CLK1/CLK2 field masks (CPG_PLL_CLK1_KDIV,
CPG_PLL_CLK1_MDIV, CPG_PLL_CLK1_PDIV and CPG_PLL_CLK2_SDIV). Update
rzv2h_cpg_pll_clk_recalc_rate() to explicitly extract those fields with
FIELD_GET and cast the KDIV extraction to s16 to ensure proper sign
extension when computing the PLL output rate.
Co-developed-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com>
Signed-off-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20251015192611.241920-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add a two-bit "instance" member to struct pll and extend the PLL_PACK()
macro to accept an instance parameter. Initialize all existing PLL
definitions with instance 0 to preserve legacy behavior. This change
enables support for SoCs with multiple PLL instances (for example,
RZ/G3E we have two PLL DSIs).
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20251015192611.241920-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add module clock and reset entries for the RTC module on the Renesas RZ/V2H
(R9A09G057) SoC.
Signed-off-by: Ovidiu Panait <ovidiu.panait.rb@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20251021080705.18116-2-ovidiu.panait.rb@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Fix a misspelling of "offsets".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/47bf5186c3a234f6a6e53d8fdc81fafd2e981534.1761033805.git.geert+renesas@glider.be
|
|
Add module clock and reset entries for the TSU0 and TSU1 blocks on the
Renesas RZ/V2H (R9A09G057) SoC.
Signed-off-by: Ovidiu Panait <ovidiu.panait.rb@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20251020143107.13974-2-ovidiu.panait.rb@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
On the RZ/T2H SoC, a specific sequence is required when releasing a
module from the module stop state (i.e. when clearing the corresponding
bit in the MSTPCRm register to '0'). After writing to the MSTPCRm
register, a read-back of the same register must be performed, followed
by at least seven dummy reads of any register within the IP block that
is being released.
To avoid mapping device registers for this purpose, a short delay is
introduced after the read-back to ensure proper hardware stabilization
before the module becomes accessible.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20251014105348.93705-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add support for module reset handling on the RZ/T2H SoC. Unlike earlier
CPG/MSSR variants, RZ/T2H uses a unified set of Module Reset Control
Registers (MRCR) where both reset and deassert actions are done via
read-modify-write (RMW) to the same register.
Introduce a new MRCR offset table (mrcr_for_rzt2h) for RZ/T2H and assign
it to reset_regs. For this SoC, the number of resets is based on the
number of MRCR registers rather than the number of module clocks. Also
add cpg_mrcr_reset_ops to implement reset, assert, and deassert using RMW
while holding the spinlock. This follows the RZ/T2H requirements, where
processing after releasing a module reset must be secured by performing
seven dummy reads of the same register, and where a module that is reset
and released again must ensure the target bit in the Module Reset Control
Register is set to 1.
Update the reset controller registration to select cpg_mrcr_reset_ops for
RZ/T2H, while keeping the existing cpg_mssr_reset_ops for other SoCs.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://patch.msgid.link/20250929112324.3622148-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add entries detailing the clocks and resets for the ISP in the
RZ/V2H(P) SoC.
Signed-off-by: Daniel Scally <dan.scally@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20251010-rzv2h_isp_clk-v2-1-2c8853a9af7c@ideasonboard.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add clock and reset entries for USB2.
Signed-off-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20251001212709.579080-10-tommaso.merciai.xr@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
The use of IS_ERR_OR_NULL() suggests that "clk" can be a NULL pointer.
Hence smatch assumes so, and issues a "passing zero to 'PTR_ERR'"
warning.
At these checkpoints, "clk" always contains either a valid pointer, or
an error pointer (none of the functions called return NULL pointers).
Hence replace IS_ERR_OR_NULL() by IS_ERR().
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/r/202408032025.ve2JMaoV-lkp@intel.com/
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://patch.msgid.link/81260328acb5c78e915ab04afad3901a31c16128.1758793709.git.geert+renesas@glider.be
|
|
Semicolons after end of function braces are not needed, remove them.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/deb1537b5f96d991332db5c8088bae705f7e17e3.1758718886.git.geert+renesas@glider.be
|
|
Renesas RZ/T2H (R9A09G077) and RZ/N2H (R9A09G087) SoCs have three 12-bit
ADC peripherals, each with their own peripheral clock.
For conversion, they use the PCLKL clock.
Add their clocks to the list of module clocks.
Signed-off-by: Cosmin Tanislav <cosmin-gabriel.tanislav.xa@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20250923160524.1096720-2-cosmin-gabriel.tanislav.xa@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
On R-Car V4H, the PCIEC controller DBI read would generate an SError in
case the controller reset is released by writing SRSTCLR register first,
and immediately afterward reading some PCIEC controller DBI register.
The issue triggers in rcar_gen4_pcie_additional_common_init() on
dw_pcie_readl_dbi(dw, PCIE_PORT_LANE_SKEW), which on V4H is the first
read after reset_control_deassert(dw->core_rsts[DW_PCIE_PWR_RST].rstc).
The reset controller which contains the SRSTCLR register and the PCIEC
controller which contains the DBI register share the same root access
bus, but the bus then splits into separate segments before reaching each
IP. Even if the SRSTCLR write access was posted on the bus before the
DBI read access, it seems the DBI read access may reach the PCIEC
controller before the SRSTCLR write completed, and trigger the SError.
Mitigate the issue by adding a dummy SRSTCLR read, which assures the
SRSTCLR write completes fully and is latched into the reset controller,
before the PCIEC DBI read access can occur.
Fixes: 0ab55cf18341 ("clk: renesas: cpg-mssr: Add support for R-Car V4H")
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20250922162113.113223-1-marek.vasut+renesas@mailbox.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
R-Car V4H Reference Manual R19UH0186EJ0130 Rev.1.30 Apr. 21, 2025 page
583 Figure 9.3.1(a) Software Reset flow (A) as well as flow (B) / (C)
indicate after reset has been asserted by writing a matching reset bit
into register SRCR, it is mandatory to wait 1ms.
This 1ms delay is documented on R-Car V4H and V4M, it is currently
unclear whether S4 is affected as well. This patch does apply the extra
delay on R-Car S4 as well.
Fix the reset driver to respect the additional delay when toggling
resets. Drivers which use separate reset_control_(de)assert() must
assure matching delay in their driver code.
Fixes: 0ab55cf18341 ("clk: renesas: cpg-mssr: Add support for R-Car V4H")
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20250918030552.331389-1-marek.vasut+renesas@mailbox.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
The clock drivers for RZ/V2H and RZ/V2N are very similar.
Reduce the differences between them by:
- Moving and reformatting the PLLCM33_GEAR clock definitions,
- Replacing spaces by TABs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/2246d2263e8a24d1aaf653db2004cbf2263c9048.1757606097.git.geert+renesas@glider.be
|
|
Add USB3.0 clock and reset entries.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20250909180803.140939-3-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
In case of krealloc_array() failure, the current error handling just
returns from the function without freeing the original array.
Fix this memory leak by freeing the original array.
Fixes: 6aa1754764901668 ("clk: renesas: cpg-mssr: Ignore all clocks assigned to non-Linux system")
Signed-off-by: Yuan CHen <chenyuan@kylinos.cn>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20250908012810.4767-1-chenyuan_fl@163.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add module clock entries for the I3C controller on the RZ/V2N
(R9A09G056) SoC.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20250904155507.245744-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add module clock entries for the I3C controller on the RZ/V2H(P)
(R9A09G057) SoC.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20250904155507.245744-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add module and core clocks used by Ethernet Subsystem (Ethernet_SS),
Ethernet MAC (GMAC), Ethernet Switch (ETHSW).
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250904071954.3176806-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Replace the ternary operator with a direct boolean comparison to improve
code readability and maintainability. The logic remains unchanged.
Signed-off-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250903082757.115778-5-tommaso.merciai.xr@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Prevent issues during reset deassertion by re-asserting the reset if a
timeout occurs when trying to deassert. This ensures the reset line is in a
known state and improves reliability for hardware that may not immediately
clear the reset monitor bit.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Link: https://lore.kernel.org/20250903082757.115778-4-tommaso.merciai.xr@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Prevent issues during reset deassertion by re-asserting the reset if a
timeout occurs when trying to deassert. This ensures the reset line is in a
known state and improves reliability for hardware that may not immediately
clear the reset monitor bit.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Link: https://lore.kernel.org/20250903082757.115778-3-tommaso.merciai.xr@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Combine common code from rzg2l_cpg_assert() and rzg2l_cpg_deassert() into a
new __rzg2l_cpg_assert() helper to avoid code duplication. This reduces
maintenance effort and improves code clarity.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Link: https://lore.kernel.org/20250903082757.115778-2-tommaso.merciai.xr@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add clock and reset entries for the Renesas RZ/G3E GPT{0,1} IPs.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250820103053.93382-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add asynchronous core clocks and module clocks for SCI channels 1
through 5 on the RZ/T2H SoC.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250812171720.3245851-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
This driver implements both the determine_rate() and round_rate() clk
ops, and the round_rate() clk ops is deprecated. When both are defined,
clk_core_determine_round_nolock() from the clk core will only use the
determine_rate() clk ops, so let's remove the round_rate() clk ops since
it's unused.
Signed-off-by: Brian Masney <bmasney@redhat.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250811-clk-for-stephen-round-rate-v1-93-b3bf97b038dc@redhat.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
The round_rate() clk ops is deprecated, so migrate this driver from
round_rate() to determine_rate() using the Coccinelle semantic patch
on the cover letter of this series.
Signed-off-by: Brian Masney <bmasney@redhat.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250811-clk-for-stephen-round-rate-v1-92-b3bf97b038dc@redhat.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Use tabs instead of spaces in the CRU clock descriptions to match the
formatting used in the rest of the clock definitions.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250806092129.621194-5-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add MSTOP configuration for all the module clocks on the RZ/G2UL
based SoCs (RZ/G2UL, RZ/Five).
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250806092129.621194-4-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
