| Age | Commit message (Collapse) | Author |
|---|
|
In most scenarios this variant is actually unused (VCR is written in
SSDR mode), but we need to provide an octal variant. The address is 24
bits but is sent over 4 bytes MSB first. This means we need to shift the
register address by one extra byte for the address to be correct.
I didn't catch this initially because the volatile register region is
256 bytes wide, so the write-then-read procedure did work with the small
register addresses I was using at that time: 0 and 1.
Fixes: 44a2f49b9bdc ("mtd: spinand: winbond: W35N octal DTR support")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Both W35N02JW and W35N04JW diverge from W35N01JW when it comes to the
"data read" operation in ODTR mode. In order to stuff more address
bits (up to 18), the second command byte is replaced by the most
significant address bits, keeping the number of address bytes to 2.
Fixes: 44a2f49b9bdc ("mtd: spinand: winbond: W35N octal DTR support")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Some devices stuff address bits in the double byte opcode (in place of
the repeated byte) in order to be able to increase the size of the
devices, without adding extra address bytes.
Create a flag to identify those devices. When the flag is set, use the
"packed" variant for the read data operation.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Factory default for this bit is "set" (at least on the chips I have),
but we must make sure it is actually set by Linux explicitly, as the
bit is writable by an earlier stage.
Fixes: 6a804fb72de5 ("mtd: spinand: winbond: add support for serial NAND flash")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Above 104MHz when in fast dual or quad I/O reads, the delay between
address and data cycles is too short. It is possible to reach higher
frequencies, up to 166MHz, by adding a few more dummy cycles through the
setting of the HS bit. Improve the condition for enabling this bit, and
also make sure we set it at soon as we go over 104MHz.
Fixes: f1a91175faaa ("mtd: spinand: winbond: Enable high-speed modes on w25n0xjw")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
This was done entirely with mindless brute force, using
git grep -l '\<k[vmz]*alloc_objs*(.*, GFP_KERNEL)' |
xargs sed -i 's/\(alloc_objs*(.*\), GFP_KERNEL)/\1)/'
to convert the new alloc_obj() users that had a simple GFP_KERNEL
argument to just drop that argument.
Note that due to the extreme simplicity of the scripting, any slightly
more complex cases spread over multiple lines would not be triggered:
they definitely exist, but this covers the vast bulk of the cases, and
the resulting diff is also then easier to check automatically.
For the same reason the 'flex' versions will be done as a separate
conversion.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This is the result of running the Coccinelle script from
scripts/coccinelle/api/kmalloc_objs.cocci. The script is designed to
avoid scalar types (which need careful case-by-case checking), and
instead replace kmalloc-family calls that allocate struct or union
object instances:
Single allocations: kmalloc(sizeof(TYPE), ...)
are replaced with: kmalloc_obj(TYPE, ...)
Array allocations: kmalloc_array(COUNT, sizeof(TYPE), ...)
are replaced with: kmalloc_objs(TYPE, COUNT, ...)
Flex array allocations: kmalloc(struct_size(PTR, FAM, COUNT), ...)
are replaced with: kmalloc_flex(*PTR, FAM, COUNT, ...)
(where TYPE may also be *VAR)
The resulting allocations no longer return "void *", instead returning
"TYPE *".
Signed-off-by: Kees Cook <kees@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"MTD:
- prioritize ofpart in physmap-core probing
- conversions to scoped for each OF child loops
Bindings:
- The bulk of the changes consists of binding fixes/updates to
restrict the use of undefined properties, which was mostly
ineffective in the current form because of the nesting of partition
nodes and the lack of compatible strings
- YAML conversions and the addition of a dma-coherent property in the
cdns,hp-nfc driver
SPI NAND:
- support for octal DTR modes (8D-8D-8D)
- support for Foresee F35SQB002G chips
And small misc fixes"
* tag 'mtd/for-7.0' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (65 commits)
mtd: spi-nor: hisi-sfc: fix refcounting bug in hisi_spi_nor_register_all()
mtd: spinand: fix NULL pointer dereference in spinand_support_vendor_ops()
mtd: rawnand: pl353: Add message about ECC mode
mtd: rawnand: pl353: Fix software ECC support
mtd: spinand: winbond: Remove unneeded semicolon
dt-bindings: mtd: cdns,hp-nfc: Add dma-coherent property
mtd: spinand: Disable continuous read during probe
mtd: spinand: add Foresee F35SQB002G flash support
mtd: spinand: winbond: W35N octal DTR support
mtd: spinand: Add octal DTR support
mtd: spinand: Warn if using SSDR-only vendor commands in a non SSDR mode
mtd: spinand: Give the bus interface to the configuration helper
mtd: spinand: Propagate the bus interface across core helpers
mtd: spinand: Add support for setting a bus interface
mtd: spinand: Gather all the bus interface steps in one single function
mtd: spinand: winbond: Configure the IO mode after the dummy cycles
mtd: spinand: winbond: Rename IO_MODE register macro
mtd: spinand: winbond: Fix style
mtd: spinand: winbond: Register W35N vendor specific operation
mtd: spinand: winbond: Register W25N vendor specific operation
...
|
|
The spinand_support_vendor_ops() helper unconditionally dereferences
info->vendor_ops. For chips that do not define vendor_ops, this pointer
is NULL, leading to a kernel panic during probe:
Unable to handle kernel NULL pointer dereference at virtual address
0000000000000008
Add a guard to return early when vendor_ops is NULL. This prevents the
crash and allows SPI NAND devices without vendor-specific operations to
be probed correctly.
Fixes: fbc7538782f8 ("mtd: spinand: List vendor specific operations and make sure they are supported")
Cc: stable@vger.kernel.org
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Remove unnecessary semicolons reported by Coccinelle/coccicheck and the
semantic patch at scripts/coccinelle/misc/semicolon.cocci.
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Macronix serial NAND devices with continuous read support do not
clear the configuration register on soft reset and lack a hardware
reset pin. When continuous read is interrupted (e.g., during reboot),
the feature remains enabled at the device level.
With continuous read enabled, the OOB area becomes inaccessible and
all reads are instead directed to the main area. As a result, during
partition allocation as part of MTD device registration, the first two
bytes of the main area for the master block are read and indicate that
the block is bad. This process repeats for every subsequent block for
the partition.
All reads and writes that reference the BBT find no good blocks and
fail.
The only paths for recovery from this state are triggering the
continuous read feature by way of raw MTD reads or through a NAND
device power drain.
Disable continuous read explicitly during spinand probe to ensure
quiescent feature state.
Fixes: 631cfdd0520d ("mtd: spi-nand: Add continuous read support")
Cc: stable@vger.kernel.org
Signed-off-by: David LaPorte <dalaport@amazon.com>
Reviewed-by: Gunnar Kudrjavets <gunnarku@amazon.com>
Reviewed-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Add support of Foresee F35SQB002G spinand flash
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Extend the support for the W35N chip family by supporting the ODTR bus
interface. The chip is capable to run in this mode, which brings a
significant performance improvement.
1S-8S-8S:
# flash_speed /dev/mtd0 -c1 -d
eraseblock write speed is 7529 KiB/s
eraseblock read speed is 15058 KiB/s
8D-8D-8D:
# flash_speed /dev/mtd0 -c1 -d
eraseblock write speed is 9481 KiB/s
eraseblock read speed is 23272 KiB/s
This is +55% read speed and +26% write speed with the same hardware.
Tests have been conducted with a TI AM62A7 using the Cadence quad SPI
controller.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Create a new bus interface named ODTR for "octal DTR", which matches the
following pattern: 8D-8D-8D.
Add octal DTR support for all the existing core operations. Add a second
set of templates for this bus interface.
Give the possibility for drivers to register their read, write and
update cache variants as well as their vendor specific operations.
Check the SPI controller driver supports all the octal DTR commands that
we might need before switching to the ODTR bus interface.
Make the switch by calling ->configure_chip() with the ODTR
parameter. Fallback in case this step fails.
If someone ever attempts to suspend a chip in octal DTR mode, there are
changes that it will loose its configuration at resume. Prevent any
problem by explicitly switching back to SSDR while suspending. Note:
there is a limitation in the current approach, page I/Os are not
available as the dirmaps will be created for the ODTR bus interface if
that option is supported and not switched back to SSDR during
suspend. Switching them is possible but would be costly and would not
bring anything as right after resuming we will switch again to ODTR. In
case this capability is used for debug, developpers should mind to
destroy and recreate suitable direct mappings.
Finally, as a side effect, we increase the buffer for reading IDs to
6. No device at this point returns 6 bytes, but we support 5 bytes IDs,
which means in octal DTR mode we have no other choice than reading an
even number of bytes, hence 6.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Both Macronix and Winbond have chip specific operations which are SSDR
only. Trying to use them in an ODTR setup will fail and doing this is a
pure software bug. Warn explicitly in this case.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
The chip configuration hook is the one responsible to actually switch
the switch between bus interfaces. It is natural to give it the bus
interface we expect with a new parameter. For now the only value we can
give is SSDR, but this is subject to change in the future, so add a bit
of extra logic in the implementations of this callback to make sure
both the core and the chip driver are aligned on the request.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
For now all drivers provide SSDR variants only. When we add support for
ODTR modes, there will be a need to differentiate the type of variant we
target as well as the need to check if we support one or the other type
of operations.
Pass this parameter to lower level helpers, which for now is unused, in
order to simplify the patch introducing ODTR support.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Create a bus interface enumeration, currently only containing the
one we support: SSDR, for single SDR, so any operation whose command is
sent over a single data line in SDR mode, ie. any operation matching
1S-XX-XX.
The main spinand_device structure gets a new parameter to store this
enumeration, for now unused. Of course it is set to SSDR during the SSDR
templates initialization to further clarify the state we are in at the
moment.
This member is subject to be used to know in which bus configuration we
and be updated by the core when we switch to faster mode(s).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Writing the quad enable bit in one helper and doing the chip
configuration in another does not make much sense from a bus interface
setup point of view.
Instead, let's create a broader helper which is going to be in charge of
all the bus configuration steps at once. This will specifically allow to
transition to octal DDR mode, and even fallback to quad (if suppoorted)
or single mode otherwise.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
When we will change the bus interface, the action that actually performs
the transition is the IO mode register write. This means after the IO
mode register write, we should use the new bus interface. But the
->configure_chip() hook itself is not responsible of making this change
official, it is the caller that must act according to the return value.
Reorganize this helper to first configure the dummy cycles before
possibly switching to another bus interface.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Suffix the macro name with *_REG to align with the rest of the driver.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Add a missing new line in the middle of the driver.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Provide the Winbond W35N specific "write VCR register" operation to let
the core verify it is supported by the controller before using it.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Provide the Winbond W25N specific "select target" operation to let the
core verify it is supported by the controller before using it.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Provide the Macronix specific "read ECC status register" operation so
that the core can verify if it is supported by the controller before
using it.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
It is probably safe to expect that all SPI controller drivers will ever
support all the most basic SPI NAND operations, such as write enable,
register reads, page program, block erases, etc. However, what about
vendor specific operations? So far nobody complained about it, but as we
are about to introduce octal DTR support, and as none of the SPI NAND
instruction set is defined in any standard, we must remain careful about
these extra operations.
One way to make sure we do not blindly get ourselves in strange
situations with vendor commands failing silently is to make the check
once for all, while probing the chip. However at this stage we have no
such list, so let's add the necessary infrastructure to allow:
- registering vendor operations,
- checking they are actually supported when appropriate.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Winbond W35N* chips require a vendor specific operation to write their
VCR register (a configuration register, typically used for tuning the
number of dummy cycles and switching to a different bus
interface). Instead of defining this op only in the function that needs
it, hiding it from the core, make it a proper define like all other
spi-mem operations, and implement the necessary spinand_fill_*_op()
helper to make the SPINAND_OP() macro work. This way we can use it from
any function without any extra handling outside of this helper when we
will convert the core to support octal DDR busses.
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Winbond W25N* chips require a vendor specific operation to select the
target. Instead of defining this op only in the function that
needs it, hiding it from the core, make it a proper define like all
other spi-mem operations, and implement the necessary
spinand_fill_*_op() helper to make the SPINAND_OP() macro work. This way
we can use it from any function without any extra handling outside of
this helper when we will convert the core to support octal DDR busses.
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Macronix chips require a vendor specific operation to read the ECC
status register. Instead of defining this op only in the function that
needs it, hiding it from the core, make it a proper define like all
other spi-mem operations, and implement the necessary
spinand_fill_*_op() helper to make the SPINAND_OP() macro work. This way
we can use it from any function without any extra handling outside of
this helper when we will convert the core to support octal DDR busses.
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Create a SPINAND_OP() macro to which we give the name of the operation
we want. This macro retrieves the correct operation template based on
the current bus interface (currently only single SDR, will soon be
extended to octal DTR) and fills it with the usual parameters.
This macro makes the transition from calling directly the low-level
macros into using the (bus interface dependent) templates very smooth.
Use it in all places that can be trivially converted. At this stage
there is no functional change expected, until octal DTR support gets
added.
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Currently, the SPI NAND core implementation directly calls macros to get
the various operations in shape. These macros are specific to the bus
interface, currently only supporting the single SDR interface (any
command following the 1S-XX-XX pattern).
Introducing support for other bus interfaces (such as octal DTR) would
mean that every user of these macros should become aware of the current
bus interface and act accordingly, picking up and adapting to the
current configuration. This would add quite a bit of boilerplate, be
repetitive as well as error prone in case we miss one occurrence.
Instead, let's create a table with all SPI NAND memory operations that
are currently supported. We initialize them with the same single SDR _OP
macros as before. This opens the possibility for users of the individual
macros to make use of these templates instead. This way, when we will add
another bus interface, we can just switch to another set of templates
and all users will magically fill in their spi_mem_op structures with
the correct ops.
The existing read, write and update cache variants are also moved in
this template array, which is barely noticeable by callers as we also
add a structure member pointing to it.
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
In order to introduce templates for all operations and not only for page
helpers (in order to introduce octal DDR support), decouple the WR_EN
and WR_DIS operations into two separate macros.
Adapt the callers accordingly.
There is no functional change.
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Replace -ENOTSUPP with -EOPNOTSUPP which is as relevant in this case but
is standard.
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
The update cache variant is mandatory, both read and write versions are
being checked, but not this one. All chip drivers seem to implement this
variant, so there should be no breakage.
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Add support for Dosilicon DS35Q1GA (3.3V) and DS35M1GA (1.8V) SPI NAND.
These are 1Gbit (128MB) devices with:
- 2048 byte pages + 64 byte OOB
- 64 pages per block, 1024 blocks
- On-die 4-bit ECC per 512 byte sector
The 64-byte OOB area is divided into 4 segments of 16 bytes, with each
segment containing 8 bytes of user data (M2+M1) and 8 bytes of ECC
parity (R1). This provides 30 bytes of usable OOB space after reserving
2 bytes for the bad block marker.
Tested on Genexis Platinum 4410 (EcoNet EN751221) by writing known
patterns to OOB and verifying ECC parity placement in R1 regions.
Datasheet:
https://www.dosilicon.com/resources/SPI%20NAND/DS35X1GAXXX_rev08.pdf
Signed-off-by: Ahmed Naseef <naseefkm@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
This reverts commit dd26402642a0899fde59ea6b0852fad3d799b4cc.
The issue George met is due to the limit of QPIC, not the issue of the
flash chip.
QPIC only supports 4 bytes ID. So the fifth byte is always 0.
If we use spi-gpio, the fifth byte can be read correctly.
Signed-off-by: Ziyang Huang <hzyitc@outlook.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull mtd updates from Miquel Raynal:
"Core MTD changes:
- We must ignore error -ENOENT from parsers on subpartitions which is
a legitimate return value
- PM support is added to the intel-dg driver
Raw NAND changes:
- The major change in this is the support for the Allwinner H616 NAND
controller, which lead to numerous changes and cleanups in the
driver.
- Another notable change in this driver is the use of field_get() and
field_prep(), but since the global support for this helpers is
going to be merged in the same release as we start using these
helpers, we undefine them in the first place to avoid warnings.
- Marvell drivers layout handling changes have also landed, they fix
previous definitions and abuses that have been made previously,
which implied to relax the ECC parameters validation in the core a
bit.
- The Cadence NAND controller driver gets NV-DDR interface support.
SPI NAND changes:
- Support for FudanMicro FM25S01BI3 and ESMT F50L1G41LC is added.
SPI NOR changes:
- Fix SMPT parsing for S25FS-S flash family. They report variable
dummy cycles for reads. This results in the default of 0 being
used. This works for other Infineon chips, but not for the S25FS-S
family. They need 8 dummy cycles. Add fixup hooks to specify that.
Also add fixup hooks to fix incorrect map ID data in SFDP.
- Add support for a bunch of Winbond flashes. Their block protection
information is not discoverable, so they need to have an entry in
the flash tables to describe that.
- Some cleanups for Micron flash support.
- Add support for Micron mt35xu01gbba.
- Some SPI controllers like the Intel one on the PCI bus do not
support the read CR opcode (0x35). Do not use the opcode if the
controller does not support it.
Aside from these main changes, there is the usual load of API updates,
kdoc fixes, potential memory leaks fixes, etc"
* tag 'mtd/for-6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (51 commits)
mtd: sm_ftl: Fix typo in comment in sm_read_lba
mtd: sm_ftl: Replace deprecated strncpy with sysfs_emit in sm_attr_show
mtd: lpddr_cmds: fix signed shifts in lpddr_cmds
mtd: docg3: fix kernel-doc warnings
mtd: spinand: add support for FudanMicro FM25S01BI3
mtd: rawnand: renesas: Handle devm_pm_runtime_enable() errors
mtd: nand: realtek-ecc: Fix Kconfig dependencies
mtd: rawnand: sunxi: #undef field_{get,prep}() before local definition
mailmap: update Pratyush Yadav's email address
mtd: spi-nor: core: Check read CR support
mtd: spi-nor: micron-st: add TODO for fixing mt35xu02gcba
mtd: spi-nor: micron-st: add mt35xu01gbba support
mtd: spi-nor: micron-st: use SFDP of mt35xu512aba
mtd: spi-nor: micron-st: move set_octal_dtr to late_init()
mtd: spi-nor: micron-st: rename the die_late_init functions
mtd: spinand: esmt: add support for F50L1G41LC
mtd: rawnand: lpc32xx_slc: Convert to use devm_gpiod_get_optional()
mtd: mtdpart: ignore error -ENOENT from parsers on subpartitions
mtd: maps: pcmciamtd: fix potential memory leak in pcmciamtd_detach()
mtd: spi-nor: spansion: SMPT fixups for S25FS-S
...
|
|
Add support for FudanMicro FM25S01BI3 SPI NAND.
Link: https://www.fmsh.com/nvm/FM25S01BI3_ds_eng.pdf
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
This adds support for ESMT F50L1G41LC, which appears to be an updated
version of the already supported F50L1G41LB.
Add esmt_8c SPI_NAND manufacturer to account for the newly used vendor
ID with support for the ESMT F50L1G41LC chip.
Link: https://github.com/openwrt/openwrt/pull/15214#issuecomment-3514824435
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
According to datasheet (http://eng.fmsh.com/nvm/FM25S01A_ds_eng.pdf)
there is no QE (Quad Enable) bit for FM25S01A flash, so remove it.
Fixes: 5f284dc15ca86 ("mtd: spinand: add support for FudanMicro FM25S01A")
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Tested-by: Tianling Shen <cnsztl@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"MTD core:
- Bad blocks increment is skipped if the block is already known bad
(improves user statistics relevance)
- Expose the OOB layout via debugfs
Raw NAND:
- Add support for Loongson-2K1000 and Loongson-2K0500 NAND
controllers, including extra features, such as chip select
and 6-byte NAND ID reading support
- Drop the s3c2410 driver
SPI NAND:
- Important SPI NAND continuous read improvements and fixes
- Add support for FudanMicro FM25S01A
- Add support for continuous reads in Gigadevice vendor driver
ECC:
- Add support for the Realtek ECC engine
SPI NOR:
- Some flashes can't perform reads or writes with start or end being
an odd number in Octal DTR mode. File systems like UBIFS can
request such reads or writes, causing the transaction to error out.
Pad the read or write transactions with extra bytes to avoid this
problem.
And the usual amount of various miscellaneous fixes"
* tag 'mtd/for-6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (46 commits)
mtd: rawnand: sunxi: drop unused module alias
mtd: rawnand: stm32_fmc2: drop unused module alias
mtd: rawnand: rockchip: drop unused module alias
mtd: rawnand: pl353: drop unused module alias
mtd: rawnand: omap2: drop unused module alias
mtd: rawnand: atmel: drop unused module alias
mtd: onenand: omap2: drop unused module alias
mtd: hyperbus: hbmc-am654: drop unused module alias
mtd: jedec_probe: use struct_size() helper for cfiq allocation
mtd: cfi: use struct_size() helper for cfiq allocation
mtd: nand: raw: gpmi: fix clocks when CONFIG_PM=N
mtd: rawnand: omap2: fix device leak on probe failure
mtd: rawnand: atmel: Fix error handling path in atmel_nand_controller_add_nands
mtd: nand: realtek-ecc: Add Realtek external ECC engine support
dt-bindings: mtd: Add realtek,rtl9301-ecc
mtd: spinand: repeat reading in regular mode if continuous reading fails
mtd: spinand: try a regular dirmap if creating a dirmap for continuous reading fails
mtd: spinand: fix direct mapping creation sizes
mtd: rawnand: fsmc: Default to autodetect buswidth
mtd: nand: move nand_check_erased_ecc_chunk() to nand/core
...
|
|
Continuous reading may result in multiple flash pages reading in one
operation. Unfortunately, not all spinand controllers support such
large reading. They will read less data. Unfortunately, the operation
can't be continued.
In this case:
* disable continuous reading on this (not good enough) spi controller
* repeat reading in regular mode.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
reading fails
Continuous reading may result in multiple flash pages reading in one
operation. Typically only one flash page has read/written (a little bit
more than 2-4 Kb), but continuous reading requires the spi controller
to read up to 512 Kb in one operation without toggling CS in beetween.
Roughly speaking spi controllers can be divided on 2 categories:
* spi controllers without dirmap acceleration support
* spi controllers with dirmap acceleration support
Firt of them will have issues with continuous reading if restriction on
the transfer length is implemented in the adjust_op_size() handler.
Second group often supports acceleration of single page only reading.
Thus enabling of continuous reading can break flash reading.
This patch tries to create dirmap for continuous reading first and
fallback to regular reading if spi controller refuses to create it.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Continuous mode is only supported for data reads, thus writing
requires only single flash page mapping.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Fix the W25N01JW's oob_layout according to the datasheet [1]
[1] https://www.winbond.com/hq/product/code-storage-flash-memory/qspinand-flash/?__locale=en&partNo=W25N01JW
Fixes: 6a804fb72de5 ("mtd: spinand: winbond: add support for serial NAND flash")
Cc: Sridharan S N <quic_sridsn@quicinc.com>
Cc: stable@vger.kernel.org
Signed-off-by: Santhosh Kumar K <s-k6@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Add support for FudanMicro FM25S01A SPI NAND.
Datasheet: http://eng.fmsh.com/nvm/FM25S01A_ds_eng.pdf
Signed-off-by: Tianling Shen <cnsztl@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
GD5F1GM9 supports a high-speed Continuous Read (CR) mode which allows
the entire memory array to be read out by a single read command
without re-issuing the 13h “Page Read to Cache” command for every page.
Datasheet summary
Feature register B0[3] (NR bit)
1 = Normal Read (default)
0 = Continuous Read (CR)
ECC status register 7Ch
Normal read: bits [3:0] → ECC status of last page
Continuous read: bits [7:4] → accumulated max bit-flips over the
whole sequential read operation.
Datasheet:
https://github.com/WT-886/DATASHEET/blob/main/GD5F1GM9-v1.0.pdf
Signed-off-by: Teng Wu <gigadevice2025@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Clarify that Winbond octal capable chips may be clocked at up to 166MHz,
which is their absolute maximum.
No per-operation maximum value (captured with a "0" in the table)
involves that in these cases the maximum frequency of the chip applies,
ie. the one commonly described in the DT.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
w35n0xjw chips can run at up to 166MHz in octal mode, but this is only
possible after programming various VCR registers.
Implement the new ->configure_chip() hook for this purpose.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
w25n0xjw chips have a high-speed capability hidden in a configuration
register. Once enabled, dual/quad SDR reads may be performed at a much
higher frequency.
Implement the new ->configure_chip() hook for this purpose and configure
the SR4 register accordingly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
