1 files changed, 132 insertions, 0 deletions
diff --git a/board/phytec/imx8mp-libra-fpsc/spl.c b/board/phytec/imx8mp-libra-fpsc/spl.c
new file mode 100644
index 00000000000..d704d588579
--- /dev/null
+++ b/board/phytec/imx8mp-libra-fpsc/spl.c
@@ -0,0 +1,132 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2025 PHYTEC Messtechnik GmbH
+ */
+
+#include <config.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/ddr.h>
+#include <asm/arch/imx8mp_pins.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/global_data.h>
+#include <asm/mach-imx/boot_mode.h>
+#include <asm/mach-imx/gpio.h>
+#include <asm/mach-imx/mxc_i2c.h>
+#include <asm/mach-imx/iomux-v3.h>
+#include <hang.h>
+#include <init.h>
+#include <log.h>
+#include <power/pmic.h>
+#include <power/pca9450.h>
+#include <spl.h>
+
+#if IS_ENABLED(CONFIG_PHYTEC_SOM_DETECTION)
+#include "../common/imx8m_som_detection.h"
+#endif
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define EEPROM_ADDR		0x51
+
+int spl_board_boot_device(enum boot_device boot_dev_spl)
+{
+	return BOOT_DEVICE_BOOTROM;
+}
+
+void spl_dram_init(void)
+{
+#if IS_ENABLED(CONFIG_PHYTEC_SOM_DETECTION)
+	int ret;
+
+	ret = phytec_eeprom_data_setup(NULL, 0, EEPROM_ADDR);
+	if (!ret) {
+		ret = phytec_imx8m_detect(NULL);
+		if (!ret)
+			phytec_print_som_info(NULL);
+	}
+#endif
+
+	ddr_init(&dram_timing);
+}
+
+#define I2C_PAD_CTRL (PAD_CTL_DSE6 | PAD_CTL_HYS | PAD_CTL_PUE | PAD_CTL_PE)
+#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
+struct i2c_pads_info i2c_pad_info1 = {
+	.scl = {
+		.i2c_mode = MX8MP_PAD_I2C1_SCL__I2C1_SCL | PC,
+		.gpio_mode = MX8MP_PAD_I2C1_SCL__GPIO5_IO14 | PC,
+		.gp = IMX_GPIO_NR(5, 14),
+	},
+	.sda = {
+		.i2c_mode = MX8MP_PAD_I2C1_SDA__I2C1_SDA | PC,
+		.gpio_mode = MX8MP_PAD_I2C1_SDA__GPIO5_IO15 | PC,
+		.gp = IMX_GPIO_NR(5, 15),
+	},
+};
+
+int power_init_board(void)
+{
+	struct pmic *p;
+	int ret;
+
+	ret = power_pca9450_init(0, 0x25);
+	if (ret)
+		printf("power init failed");
+	p = pmic_get("PCA9450");
+	pmic_probe(p);
+
+	/* BUCKxOUT_DVS0/1 control BUCK123 output */
+	pmic_reg_write(p, PCA9450_BUCK123_DVS, 0x29);
+
+	/* Increase VDD_SOC and VDD_ARM to OD voltage 0.95V */
+	pmic_reg_write(p, PCA9450_BUCK1OUT_DVS0, 0x1C);
+	pmic_reg_write(p, PCA9450_BUCK2OUT_DVS0, 0x1C);
+
+	/* Set BUCK1 DVS1 to suspend controlled through PMIC_STBY_REQ */
+	pmic_reg_write(p, PCA9450_BUCK1OUT_DVS1, 0x14);
+	pmic_reg_write(p, PCA9450_BUCK1CTRL, 0x59);
+
+	/* Set WDOG_B_CFG to cold reset */
+	pmic_reg_write(p, PCA9450_RESET_CTRL, 0xA1);
+
+	return 0;
+}
+
+void spl_board_init(void)
+{
+	arch_misc_init();
+
+	/* Set GIC clock to 500Mhz for OD VDD_SOC. */
+	clock_enable(CCGR_GIC, 0);
+	clock_set_target_val(GIC_CLK_ROOT, CLK_ROOT_ON | CLK_ROOT_SOURCE_SEL(5));
+	clock_enable(CCGR_GIC, 1);
+}
+
+int board_fit_config_name_match(const char *name)
+{
+	return 0;
+}
+
+void board_init_f(ulong dummy)
+{
+	int ret;
+
+	arch_cpu_init();
+
+	ret = spl_early_init();
+	if (ret) {
+		debug("spl_early_init() failed: %d\n", ret);
+		hang();
+	}
+
+	preloader_console_init();
+
+	enable_tzc380();
+
+	setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
+
+	power_init_board();
+
+	/* DDR initialization */
+	spl_dram_init();
+}