| Age | Commit message (Collapse) | Author |
|---|
|
Status polling is used instead of using interrupt controller for Agilex5.
Disabling GICV3 in Agilex5 target, as well as disabling GICV2 enabled by
default for all SoCFPGA devices.
All the other SoCFPGA devices uses GICV2, thus enabling GICV2 in each of
the devices.
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
Signed-off-by: Tien Fong Chee <tien.fong.chee@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
|
|
There are 5 L4 watchdogs and one SDM triggered warm reset bit
in Agilex5 reset manager "stat" register where bit 16:20 for L4
watchdogs. Assigning value 1 to these bits in the register address
will initiate SDM to trigger warm reset.
Introducing new warm reset mask for Agilex5 to trigger warm reset
to all five L4 watchdogs.
Signed-off-by: Tien Fong Chee <tien.fong.chee@altera.com>
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
|
|
PLL frequency would overshoot from the original target in
synchronous mode during low VCC voltage condition.
To resolve this issue, PLL is set to run on asynchronous mode
instead of enabling synchronous mode in the clock driver.
Signed-off-by: Muhammad Hazim Izzat Zamri <muhammad.hazim.izzat.zamri@altera.com>
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
|
|
Replace cm_wait_for_fsm() function with wait_for_bit_le32() function
which supports accurate timeout.
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
Signed-off-by: Tien Fong Chee <tien.fong.chee@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
|
|
Some customers prefer to minimize the use of external oscillators,
especially when using the FPGA first configuration mode.
By enabling the configuration of the HPS internal oscillator as
the boot_clk source instead of the default external oscillator,
(HPS_OSC_CLK) in non-secure boot scenarios, this allows them
to eliminate the need for an additional oscillator device and
a dedicated HPS pin, simplifying board layout and routing.
Signed-off-by: Tingting Meng <tingting.meng@altera.com>
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
|
|
Agilex5 retrieves its clock manager address via probing its own clock
driver model during SPL initialization.
Therefore, excluding Agilex5 from calling generic clock driver in misc
driver.
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@intel.com>
|
|
Initial creation of new system manager driver.
Add supports for the SOCFPGA System Manager Register block which
aggregates different peripheral function into one area.
On 64 bit ARM parts, the system manager only can be accessed during
EL3 mode, this driver model provide user the high level access
to system register and abstract user from low level access.
The base address of system manager can be retrieved
using DT framework through the System Manager driver.
Signed-off-by: Tien Fong Chee <tien.fong.chee@altera.com>
Signed-off-by: Boon Khai Ng <boon.khai.ng@altera.com>
|
|
Enable i2c3 node in Agilex5 device tree
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
|
|
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
For eMMC v4 and newer that is smaller than 2 GiB, the JEDEC JESD84-B51
section 6.2.4 Configure partitions indicates that EXT_CSD SEC_COUNT
should not be used to determine device size, and instead device size
should be calculated from C_SIZE and C_SIZE_MULT.
This is not exactly accurate, the 2 GiB limit is not a hard line,
there are eMMC devices which are smaller than 2 GiB and still
require device size to be determined from EXT_CSD SEC_COUNT. The
hard line is instead OCR HCS bit, which indicates whether the device
is byte or sector addressed, the former applies to most devices
below 2 GiB, and the later applies mostly to devices above 2 GiB.
However, there are a couple of devices which are smaller than 2 GiB
and still set the OCR HCS bit to indicate they are sector addressed,
and therefore the size calculation for those devices should also
use EXT_CSD SEC_COUNT . Use mmc->high_capacity flag to discern the
devices instead of arbitrary 2 GiB limit. The mmc->high_capacity flag
reflects the OCR HCS bit state.
Fixes: 639b7827d1ca ("mmc: fix the condition for MMC version 4")
Signed-off-by: Marek Vasut <marex@denx.de>
|
|
The length of buffers used to read inode tables, directory tables, and
reading a file are calculated as: number of blocks * block size, and
such plain multiplication is prone to overflowing (thus unsafe).
Replace it by __builtin_mul_overflow, i.e. safe math.
Signed-off-by: Joao Marcos Costa <joaomarcos.costa@bootlin.com>
|
|
Branch contains bringup of Acer Iconia Tab A500 (codename picasso), a
Tegra 2 Android device with decent Linux kernel support. Ondevice tests
and U-Boot test suit all passed.
|
|
https://source.denx.de/u-boot/custodians/u-boot-efi
CI:
* https://source.denx.de/u-boot/custodians/u-boot-efi/-/pipelines/24709
UEFI:
* create a parent device for all EFI block devices
* move lmb_map_update_notify() to EFI
* make efi_add_memory_map_pg() static
* remove comparisons to string literals from runtime
* ix potential deref-after-null
Other:
* avoid superfluous value check in lmb_map_update_notify()
* support more efi protocols in uuid_guid_get_str()
|
|
CI: https://source.denx.de/u-boot/custodians/u-boot-riscv/-/pipelines/24692
- board: VisionFive 2: Update maintainer file
- configs: starfive: Add LwIP network and wget command
- configs: microchip: set DEFAULT_FDT_FILE
|
|
https://source.denx.de/u-boot/custodians/u-boot-rockchip
CI: https://source.denx.de/u-boot/custodians/u-boot-rockchip/-/pipelines/24690
Please pull the fixes for rockchip platform:
- Fix for rk3399 bob and kevin
- Fix for sdram more than 4GB
- Fix for dwc_eth on rk356x/rk3588
- Fix for sdmmc access on rk33080rock-s9
|
|
The function is only used in the efi_memory.c module.
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
|
|
When building with qemu_arm64_defconfig with CONFIG_CC_OPTIMIZE_FOR_DEBUG=y
and CONFIG_EFI_LOADER=n an error undefined reference to efi_add_memory_map_pg
occurs.
Move the EFI dependent part of lmb_map_update_notify() to the EFI
sub-system.
Reported-by: Liya Huang <1425075683@qq.com>
Acked-by: Liya Huang <1425075683@qq.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
|
|
Instead of testing the value of parameter op at runtime use an enum to
ensure that only valid values are used.
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
|
|
Up to now root has been the parent device for all block devices created via
calling ConnectController(). This does not work well together with the
implementation of bootstd.
Add a dummy parent device for all EFI block devices.
With this change EFI block devices are also accessible via commands like
'cat', 'load', and 'ls'.
=> dm tree
Class Seq Probed Driver Name
-----------------------------------------------------------
efi 0 [ + ] EFI block driver `-- efi
blk 3 [ + ] efi_blk `-- efi.efiblk#0
partition 0 [ + ] blk_partition `-- efi.efiblk#0:1
=> ls efiloader 0:1
13 hello.txt
7 u-boot.txt
2 file(s), 0 dir(s)
=> cat efiloader 0:1 hello.txt
Hello world!
=> efidebug dh
0000000018df1700 (efi.efiblk#0:1)
/VenHw(dbca4c98-6cb0-694d-0872-819c650cb7b8)/HD(1,MBR,0xd1535d21,0x1,0x7f)
Block IO
Simple File System
Adjust the event dump unit test to consider the new event spy.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
|
|
For EFI runtime services, we manage to preserve string literals
by placing the .efi_runtime section just before .data and preserving
it when marking the runtime memory by marking surrounding boottime
code as runtime. This is ok for now but will break if we update any
linker scripts and decouple .text and .runtime sections.
So let's define the strings we used to compare in the appropriate
section for runtime services
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
|
|
After having been compared to a NULL value at efi_disk.c:426,
pointer 'part_info' is dereferenced at efi_disk.c:534.
Signed-off-by: Maks Mishin <maks.mishinFZ@gmail.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
|
|
Add more EFI protocols GUIDs to the translation table used by
uuid_guid_get_str().
Signed-off-by: Vincent Stehlé <vincent.stehle@arm.com>
Cc: Tom Rini <trini@konsulko.com>
|
|
Use LwIP network stack and enable wget HTTP command. The tftpput command
is not currently supported by LwIP network stack so remove it.
Signed-off-by: E Shattow <e@freeshell.de>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
|
|
Update the maintainer file and mark jh7110 / visionfive2 related files
with N: patterns.
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
|
|
Variable $fdtfile needs to be set for automatically loading a device-tree
from the ESP or boot partition.
* Set CONFIG_DEFAULT_FDT_FILE in the defconfig.
* Add $fdtfile to the default environment.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
|
|
BootROM leave GPIO4_D6 configured as SDMMC_PWREN function and DW MCI
driver set PRWEN high on MMC_POWER_UP and low on MMC_POWER_OFF.
Similarly U-Boot also set PRWEN high before accessing mmc.
However, HW revision prior to v1.2 must pull GPIO4_D6 low to access
sdmmc. For HW revision v1.2 the state of GPIO4_D6 has no impact.
Model an always-on active low fixed regulator using GPIO4_D6 to fix
use of sdmmc on older HW revisions of the board.
Fixes: adeb5d2a4ba4 ("arm64: dts: rockchip: Add Radxa ROCK S0")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20241119230838.4137130-1-jonas@kwiboo.se
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
[ upstream commit: 26c100232b09ced0857306ac9831a4fa9c9aa231 ]
(cherry picked from commit ca8e0bedbc790b19b11efc223677d178b8eeb74e)
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
|
|
When rgmii-rxid/txid/id phy-mode is used the MAC should not add RX
and/or TX delay. Currently RX/TX delay is configured as enabled using
zero as delay value for the rgmii-rxid/txid/id modes.
Change to disable RX and/or TX delay and using zero as delay value.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
When rgmii-rxid/txid/id phy-mode is used the MAC should not add RX
and/or TX delay. Currently RX/TX delay is configured as enabled using
zero as delay value for the rgmii-rxid/txid/id modes.
Change to disable RX and/or TX delay and using zero as delay value.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
The pinmux bits for GPIO2-B0 to GPIO2-B6 actually have 2 bits width,
correct the bank flag for GPIO2-B. The pinmux bits for GPIO2-B7 is
recalculated so it remain unchanged. Add missing GPIO3-B1 to GPIO3-B7
pinmux data to rk3328_mux_recalced_data as mux register offset for these
pins does not follow rockchip convention.
This matches changes in following Linux commits:
- e8448a6c817c ("pinctrl: rockchip: fix pinmux bits for RK3328 GPIO2-B pins")
- 5ef6914e0bf5 ("pinctrl: rockchip: fix pinmux bits for RK3328 GPIO3-B pins")
- 128f71fe014f ("pinctrl: rockchip: correct RK3328 iomux width flag for GPIO2-B pins")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
clock/rk3288-cru.h in include/dt-bindings is almost identical to the
version in dts/upstream, remove the copy from include/dt-bindings to
only use the version from dts/upstream.
One clk, SCLK_MAC_PLL, is not part of the upstream bindings, this clk is
not used by upstream, in-tree or vendor DTs and can safely be dropped.
No functional change to board DTs is intended with this removal.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
The device tree for rk3036 combined is now
available in the /dts/upstream directory.
Use imply OF_UPSTREAM to migrate all rk3036 boards.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
|
|
Most Rockchip SoCs use 0x0 as DRAM base address, however some SoCs use
0x60000000 and RK3576 use 0x40000000 as DRAM base address.
CFG_SYS_SDRAM_BASE is defined with correct address for each SoC and
U-Boot proper use this to set correct gd->ram_base in setup_dest_addr().
SPL never assign any value to gd->ram_base and instead use the default,
0x0. Set correct gd->ram_base in dram_init() to ensure its correctness
in SPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
U-Boot only works correctly when it uses RAM below the 4G address
boundary on Rockchip SoCs. Limit usable gd->ram_top to max 4G.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Allow the first bank to extend beyond 4 GiB when the blob of space for
peripheral is located before start of DRAM, e.g. when start of DRAM
is 0x40000000 and continue beyond the 4 GiB mark.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
In the GRF header file, some instances of UART2 pinmux are prefixed with
"GRF_UART2DBG" while others have "GRF_UART2DGB".
Since UART2 is the default console UART and used for debugging, it is
more likely the name should be UART2DBG.
Fix the ones that are wrong.
Fixes: a2c08df3813b ("pinctrl: add driver for rk3399")
Fixes: fa72de10452c ("rockchip: arm64: rk3399: move grf register definitions to grf_rk3399.h")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Paul Kocialkowski <paulk@sys-base.io>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
These power rails must be on very early for the U-Boos TPL banner to be
show over debug UART.
This reverts commit 4576e65a5d6b10fd207c3a44061676ce0220d794.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
The PP1500 and PP3000 power rails must be on very early for the U-Boot
TPL banner to be shown on debug UART.
Enable TPL_GPIO Kconfig option for bob and kevin to allow use of
spl_gpio.h functions in TPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
These power rails must be on very early for the U-Boos SPL banner to be
show over debug UART.
This reverts commit af518a1dfe637cb4dc486d7a832585e4a48bc970.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Add the dram_init_banksize function to the board file to properly set
DRAM memory sizes during boot.
The commit bc07851897bd ("board: ti: Pull redundant DDR functions to a
common location and Fixup DDR size when ECC is enabled") relocated the
dram_init_banksize function from architecture specific initialization to
the TI board initialization code. As a result, boards relying on the
previous setup now require this function to be defined within their
board file to handle DRAM sizing correctly.
Without this function defined the following error appears during boot:
ERROR: Failed to allocate 0x1000 bytes below 0x0.
Fixes: bc07851897bd ("board: ti: Pull redundant DDR functions to a common location and Fixup DDR size when ECC is enabled")
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Acked-by: Francesco Dolcini <francesco.dolcini@toradex.com>
|
|
See the original report [1], otherwise len + 1 will be overflowed.
Note that EROFS archive can record arbitary symlink sizes in principle,
so we don't assume a short number like 4096.
[1] https://lore.kernel.org/r/20250210164151.GN1233568@bill-the-cat
Fixes: 830613f8f5bb ("fs/erofs: add erofs filesystem support")
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
|
|
The following was reported by Covervity scan:
*** CID 541279: (TAINTED_SCALAR)
/drivers/led/led-uclass.c: 284 in led_get_function_name()
278 if (!ret) {
279 snprintf(uc_plat->name, LED_MAX_NAME_SIZE,
280 "%s:%s-%d",
281 cp ? "" : led_colors[color],
282 func ? func : "", enumerator);
283 } else {
>>> CID 541279: (TAINTED_SCALAR)
>>> Using tainted variable "color" as an index into an array "led_colors".
Fix it.
Addresses-Coverity-ID: 541279 (TAINTED_SCALAR)
Link: https://lists.denx.de/pipermail/u-boot/2025-February/580250.html
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
The PRNG implementing the random() function only has 2^31 states and
therefore is unsafe to use for cryptography. Use arc4random() instead.
Fixes: cc34f04efd63 ("tools: image-host.c: use random instead of rand")
Addresses-Coverity-ID: 312953 Calling risky function
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
|
|
As per TRM[0] Section 8.7.1 "TPS6594-Q1 Registers", LDOx_Vout
bit 6-1, define the NVM voltage settings.
Along side table 8-4 of above TRM, shows voltage to value mapping.
Driver wrongly using bits 5-1 to calculate voltage, and to convert
voltage to value driver was using buck's calculation.
So fix those calculation.
[0]: https://www.ti.com/lit/ds/symlink/tps6594-q1.pdf
Fixes: 5d7dbd22cf7d ("power: regulator: tps65941: use function callbacks for conversion ops")
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
|
|
The struct contains an iomem pointer that we later remap and update.
Remove const from the struct definition.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
|
|
When adding the symlink for the conf file so qemu_arm64_lwip uses
qemu_arm64 configuration information, the symlink for the boardenv file
was missed in Gitlab (but not Azure). Add that in now.
Fixes: fd10d156db3f ("CI: add qemu_arm64_lwip to the test matrix")
Reviewed-by: Jerome Forissier <jerome.forissier@linaro.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
The Acer Iconia A500 is a tablet computer designed, developed and
marketed by Acer Inc. It is powered by 1 GHz Nvidia Tegra 2 processor
and 1GB DDR2 RAM. The A500 is sold with 64 GB, although both 16 GB
and 32 GB models are available.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
|
|
Add empty weak assembler function armv8_switch_to_el2_prep() which is
jumped to just before U-Boot determines which EL it is running in and
decides which path to take to boot the Linux kernel. Add
IH_TYPE_TFA_BL31 into supported images type, to allow implementation of
board specific U_BOOT_FIT_LOADABLE_HANDLER(IH_TYPE_TFA_BL31, ...) TFA
BL31 loadable handler for fitImages.
This PR contains common hooks which are noop, R-Car Gen4 board specific
implementation using these hooks is coming in next PR.
|
|
Add support for starting TFA from U-Boot running in EL3 as part of
fitImage boot, so the user can start U-Boot in the highest privilege
level on the platform, bundle TFA, Linux, DT into a single fitImage
and boot such a bundle as a whole.
There are two main benefits of this approach. First is the ability
to run U-Boot in EL3, where it has unrestricted access to the entire
system and can act as a useful debug tool, as it was always intended
to be used. Second is the ability to easily and safely update of any
component in the fitImage, be it TFA, Linux or DT.
The boot process is similar to regular Linux with DT fitImage boot
process, except the TFA has to be bundled into the fitImage. For the
bundling instructions, see below. The TFA is started as a 'loadables'
with custom U_BOOT_FIT_LOADABLE_HANDLER and armv8_switch_to_el2_prep()
handling implemented in board code, and performing the handoff and
boot in case the TFA was loaded.
The loadables handler is optional and meant to set up any sort of
handoff structures used by the TFA BL31 or perform any other setup
that is needed by the blob. The custom armv8_switch_to_el2_prep()
has to implement the jump to TFA BL31 with return to U-Boot just
before booting the Linux kernel.
Example fitImage image and configuration section:
/dts-v1/;
/ {
description = "Linux kernel with FDT blob and TFA BL31";
images {
kernel-1 { ... };
fdt-1 { ... };
atf-1 { /* This is the TFA BL31 image */
description = "TFA BL31";
data = /incbin/("../build/plat/release/bl31.bin");
type = "tfa-bl31";
arch = "arm64";
os = "arm-trusted-firmware";
compression = "none";
load = <0x46400000>;
entry = <0x46400000>;
};
};
configurations {
default = "conf-1";
conf-1 {
description = "Boot Linux";
kernel = "kernel-1";
fdt = "fdt-1";
loadables = "atf-1"; /* This is the TFA BL31 loadable */
};
};
};
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
|
Add empty weak assembler function armv8_switch_to_el2_prep() which is
jumped to just before U-Boot determines which EL it is running in and
decides which path to take to boot the Linux kernel.
This weak function is meant to be used by architecture specific code
to implement jump to a firmware blob, which then returns right past
this weak function and continues execution of U-Boot code which then
boots the Linux kernel. One example of such use case is when U-Boot
jump tp TFA BL31, which switches from EL3 to EL2 and then returns to
U-Boot code newly running in EL2 and starts the Linux kernel.
The weak function is called with caches already disabled and DM shut
down. Any preparatory work or even loading of more data must be done
in board_prep_linux(), this hook is meant only for the final jump to
the firmware and return to U-Boot before booting Linux.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
|
Improvements for PMIC GPIO children, tegra20 pinmux driver fix, tegra
dts updates, various small adjustments and tweaks.
|
