| Age | Commit message (Collapse) | Author |
|---|
|
https://source.denx.de/u-boot/custodians/u-boot-rockchip into next
CI: https://source.denx.de/u-boot/custodians/u-boot-rockchip/-/pipelines/21113
- New board: Theobroma Systems SOM-RK3588-Q7 Tiger, ArmSoM Sige7 Rk3588;
- PX30 dts migrate to OF_UPSTREAM;
- Some other update on board or config;
|
|
Loading and running the ELF image is the responsibility of the
library and should not be associated with the command line interface.
It is also required to run ELF images from FIT with the bootm command
so as not to depend on the command line interface.
Signed-off-by: Maxim Moskalets <maximmosk4@gmail.com>
|
|
Here the size should be `length - skip`, otherwise it could cause
the destination buffer overflow.
Reported-by: jianqiang wang <wjq.sec@gmail.com>
Fixes: 65cb73057b65 ("fs/erofs: add lz4 decompression support")
Signed-off-by: Jianan Huang <jnhuang95@gmail.com>
Reviewed-by: Gao Xiang <hsiangkao@linux.alibaba.com>
|
|
Add combined binaries for all Verdin AM62 variants.
These binaries can be used to flash the U-Boot via single
binary instead of few as it is done at the moment.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
|
|
Bryan Brattlof <bb@ti.com> says:
Hello Again Everyone!
The am625-lp-sk is a variant of the am625-sk showcasing the low-power
features of the am625 SoC Family. Because it's essentially a board and
package spin of the am625-sk I've inherited the am625 configuration and
overridden what was needed.
This is a new spin of Nitin's original work which has been updated
significantly since October 2023
https://lore.kernel.org/u-boot/20231030110138.1347603-1-n-yadav@ti.com/
For those of us interested here is proof of life using buildroot:
https://paste.sr.ht/~bryanb/40f7787f7760bee383aa8fbc342a29e8544dbdab
This also works around a buildman issue not following #include
directives. To get around this I've redefined the variables it's looking
for inside the lp-sk defconfig to keep it happy for now. I made a pull
request on github and everything seems like it's happy
https://dev.azure.com/u-boot/u-boot/_build/results?buildId=8634&view=results
|
|
Dhruva Gole <d-gole@ti.com> says:
Add support for signing of TIFSSTUB images for HSSE, HSFS and GP devices
and include them in tispl.bin and tispl.bin_unsigned in AM62A.
AM62P doesn't have any GP support, hence not applicable.
These changes are required for Low Power Mode features to work on these
SoCs as this TIFS Stub gets used in the Low Power Exit sequences.
Boot tested on both platforms that are being touched:
[0] AM62A, [1] AM62P
[0] https://gist.github.com/DhruvaG2000/d5f2a46818d8025a540efe9289feacb4
[1] https://gist.github.com/DhruvaG2000/ce29f6e9315a78d3e9e5810f55f17f43
|
|
Nishanth Menon <nm@ti.com> says:
Cleanup am625 on by switching over the last two platforms (SK and
beagleplay) over to OF_UPSTREAM, and while at it, switch over am62a7
(last of the am62* family) over as well.
This superscedes the previous version of beagleplay only patch[1]
Test logs: https://gist.github.com/nmenon/ba310d3750a80789aca6a4fd90190135
|
|
Adds TIFS stub binaries, this is required for deepsleep functionality.
This implements the same change as commit 128f81290b7d ("arm: dts: k3:
binman: am625: add support for signing TIFSSTUB Images") did for TI AM62
SK board.
Signed-off-by: Vibhore Vardhan <vibhore@ti.com>
Signed-off-by: Dhruva Gole <d-gole@ti.com>
|
|
Tom Rini <trini@konsulko.com> says:
Rework how the BLK symbol is used now that so much DM migration has been
completed.
|
|
Add support for signing of TIFSSTUB images for HSSE, HSFS and GP devices
and include them in tispl.bin and tispl.bin_unsigned.
This implements the same change as commit 128f81290b7d ("arm: dts: k3:
binman: am625: add support for signing TIFSSTUB Images") did for TI AM62
SK board.
Signed-off-by: Vibhore Vardhan <vibhore@ti.com>
Signed-off-by: Dhruva Gole <d-gole@ti.com>
|
|
Jonathan Humphreys <j-humphreys@ti.com> says:
Add binman nodes for EFI capsules of firmware components so that capsules
are automatically created during the UBoot builds.
This is enabled for several TI SoC based platforms: AM64, AM62, AM62p,
BeaglePlay, AM69, J7, and BeagleboneAI.
|
|
Fill in the AM69 SK's capsule GUID properties of the base binman
capsule nodes.
Signed-off-by: Jonathan Humphreys <j-humphreys@ti.com>
|
|
Fill in the BeagleBoneAI64's capsule GUID properties of the base binman
capsule nodes. Also add it's SYSFW binman capsule node.
Signed-off-by: Jonathan Humphreys <j-humphreys@ti.com>
|
|
Fill in the am62x SK's capsule GUID properties of the base binman capsule
nodes.
Signed-off-by: Jonathan Humphreys <j-humphreys@ti.com>
|
|
Fill in the am62px SK's capsule GUID properties of the base binman capsule
nodes.
Signed-off-by: Jonathan Humphreys <j-humphreys@ti.com>
|
|
Fill in the BeaglePlay's capsule GUID properties of the base binman capsule
nodes.
Signed-off-by: Jonathan Humphreys <j-humphreys@ti.com>
|
|
Fill in the J721e SK's capsule GUID properties of the base binman capsule
nodes.
Also add it's SYSFW binman capsule node.
Signed-off-by: Jonathan Humphreys <j-humphreys@ti.com>
|
|
Fill in the am64x SK's capsule GUID properties of the base binman capsule
nodes.
Signed-off-by: Jonathan Humphreys <j-humphreys@ti.com>
|
|
Create capsule files for tiboot3.bin, tispl.bin, and u-boot.img.
Signed-off-by: Jonathan Humphreys <j-humphreys@ti.com>
|
|
Trigger the building of the mkeficapsule tool if EFI_LOADER is enabled.
Previously it was triggered on EFI_CAPSULE_ON_DISK, but mkeficapsule is
needed when a capsule is being generated for a bootloader stage, not just
from the stage applying them. EFI_LOADER is a more accurate approximation
of when a capsule may need to be generated.
Signed-off-by: Jonathan Humphreys <j-humphreys@ti.com>
|
|
The am62x-lp-sk is a package and reference board spin of the am62x-sk to
showcase the low-power features of the am62x SoC family. Because it so
closely resembles the am62x-sk board, use the preprocessor to inherit
its configuration making the needed changes for this board where
necessary.
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
|
|
Add the U-Boot device tree overrides for the am62x-lp-sk reference
board.
Signed-off-by: Nitin Yadav <n-yadav@ti.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
|
|
Enable OF_UPSTREAM for am62a7-sk board. Remove DT files that
are now available in dts/upstream. Update the appended files based on
version of latest OF_UPSTREAM sync point (v6.10-rc1).
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
|
|
Enable OF_UPSTREAM for am625-sk board. Remove DT files that
are now available in dts/upstream. Update the appended files based on
version of latest OF_UPSTREAM sync point (v6.10-rc1).
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
|
|
Enable OF_UPSTREAM for AM625-beagleplay board. Remove DT files that
are now available in dts/upstream. Update the appended files based on
version of latest OF_UPSTREAM sync point (v6.10-rc1).
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
|
|
At this point in the DM migration, all platforms enable DM. BLK requires
DM. Make BLK "def_bool y" in the cases it had been "default y" to make
this clearer. Now remove the symbol requirement from other places as it
is redundant here.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
As this is an SPL related driver, and in SPL enabling SPL_BLK is
optional, make this depend on the correct symbol.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
The BLK symbol is used both for "we have a block device subsystem
enabled" and "we need to utilize the block device library functions". In
the case of efi_loader, it is the case of "we need to utilize the block
device library", so select rather than depends on it. In turn, also
disable EFI_LOADER on platforms which did not have it on previously due
to a lack of block devices. They can enable it themselves if desired.
Acked-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Disable support for unused OSes as Linux is the primary target.
Disable support for bootz as zImage isn't a format compatible with
Aarch64 machines so it should never be attempted to be booted.
Enable a bunch of commands:
- erofs
- gpio
- squashfs
that could be useful and are also found in Jaguar and Tiger defconfigs.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
RK3588 Jaguar and Tiger, and RK3399 Puma use standard boot with the full
feature set, so let's do that as well for PX30 Ringneck.
Disable support for unused OSes as Linux is the primary target.
Enable a bunch of commands:
- boot/bootd
- erofs
- gpio
- iminfo
- imxtract
- itest
- pmic
- regulator
- sleep
- squashfs
that could be useful and are also found in Jaguar and Tiger defconfigs.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
The RK3588-Q7 SoM is a Qseven-compatible (70mm x 70mm, MXM-230
connector) system-on-module from Theobroma Systems, featuring the
Rockchip RK3588.
It provides the following feature set:
* up to 16GB LPDDR4x
* on-module eMMC
* SD card (on a baseboard) via edge connector
* Gigabit Ethernet with on-module GbE PHY
* HDMI/eDP
* MIPI-DSI
* 4x MIPI-CSI (3x on FPC connectors, 1x over Q7)
* HDMI input over FPC connector
* CAN
* USB
- 1x USB 3.0 dual-role (direct connection)
- 2x USB 3.0 host + 1x USB 2.0 host
* PCIe
- 1x PCIe 2.1 Gen3, 4 lanes
- 2xSATA / 2x PCIe 2.1 Gen1, 2 lanes
* on-module ATtiny816 companion controller, implementing:
- low-power RTC functionality (ISL1208 emulation)
- fan controller (AMC6821 emulation)
* on-module Secure Element with Global Platform 2.2.1 compliant
JavaCard environment
The support is added for Tiger on Haikou devkit, similarly to RK3399
Puma and PX30 Ringneck.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Apart from the host-only usb3 controller (host2) the rk3588 also provides
two dual-role controllers. On the Tiger-Haikou combination these are
connected to the lower usb3-host port in host-only mode and the micro-usb3
port for dual-role operation.
Add the necessary controllers, phys to the Tiger-Haikou board and enable
the usb-id extcon.
Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
Reviewed-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Link: https://lore.kernel.org/r/20240422163951.2604273-4-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
[ upstream commit: d7b83921d098bd76623381f75f5cd2296f1315cc ]
(cherry picked from commit 193d3b2a0a98f2dcd8c43bcbf8a766098a9fa75d)
|
|
The Q7 standard specifies a usb-id pin on the connector to distiuish
between host and device mode. Model this via the usb-id extcon binding.
While the pin is part of the Q7 standard, so part of the module, the
extcon stays disabled in the som dtsi and will only be enabled in a
baseboard using it.
Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
Reviewed-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Link: https://lore.kernel.org/r/20240422163951.2604273-3-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
[ upstream commit: eabb53f5dacfd643b5255f35bad30b8f914decdc ]
(cherry picked from commit 4843cec4092318ef7feb0999b0d34ef817465b33)
|
|
The comment for the host2_xhci points to the wrong port on the board.
The upper usb3 port is the correct one, so fix the comment to prevent
confusion.
Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
Reviewed-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Link: https://lore.kernel.org/r/20240422163951.2604273-2-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
[ upstream commit: 3482efee1144262dc839792103e6a9e29defecbc ]
(cherry picked from commit 56f3031edf22d163f10bc4b631d37a9aaa82d4d4)
|
|
The clock-generator of course only produces a 100MHz clock rate,
not 1GHz.
Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
Reviewed-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Link: https://lore.kernel.org/r/20240423114635.2637310-1-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
[ upstream commit: 0eb2a93518fb4728bd1d55fcd3b57fce4797ef1d ]
(cherry picked from commit b574cbafae976cf508692088944e45c9764c0048)
|
|
gpio_pwrctrl2 gets duplicated by both rk806_dvs1_null and rk806_dvs2_null
gpio_pwrctrl1 is unset. This typo appears in multiple files. Let's fix them.
Note: I haven't had the chance to test them all because I don't own all
of these boards (obviously). Please test if it's needed.
Signed-off-by: Jing Luo <jing@jing.rocks>
Link: https://lore.kernel.org/r/20240420130355.639406-1-jing@jing.rocks
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
[ upstream commit: d7f2039e5321636069baa77ef2f1e5d22cb69a88 ]
(cherry picked from commit cb2b6d1d19ed10fcaec5f5859c08a3355d1c66e0)
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
The association of uart2 to the q7-uart pins is part of the module
itself and not the baseboard used. Therefore move the pinctrl over
to the tiger dtsi.
Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
Reviewed-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Link: https://lore.kernel.org/r/20240422143356.2596414-1-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
[ upstream commit: 5adbad5c464a708a87cf5ade1bfe2ca947bb2f82 ]
(cherry picked from commit f8314a4fbc00a3d651a7e9b4d9462d10c6c02a12)
|
|
Enable the mali gpu node and add the som-specific supply-regulator.
Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
Reviewed-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Link: https://lore.kernel.org/r/20240327112120.1181570-2-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
[ upstream commit: f5256f8ed4b729c3ab9d9cd7d406313773484b59 ]
(cherry picked from commit 27350b241eafea37dc94743cd9c5dd83295faca9)
|
|
Ringneck was mistakenly set to allow up to 128KiB for the TPL code size
while PX30 SoC only has 16KiB of SRAM.
Therefore, let's use the default value of TPL_MAX_SIZE from the SoC
(which is 10KiB) so that the max code size is actually checked and
useful.
Fixes: c925be73a0a8 ("rockchip: add support for PX30 Ringneck SoM on Haikou Devkit")
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
|
|
The ID of the PMIC is stored in the 2 16b registers but the only part
that matters right now is the 3 MSB, which make the 3 digits (in hex) of
the part number.
Right now, only RK808 was properly displayed, with this all currently
supported PMICs should display the proper part number.
Additionally, when the PMIC variant is not found, print that value
instead of the masked unshifted value as all PMICs we support for now
have their LSB ignored to represent the actual part number.
Tested on RK806 (RK3588 Jaguar), RK808 (RK3399 Puma) and RK809 (PX30
Ringneck).
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
|
|
On px30-ringneck the FIT payload is located at sector 0x200 compared to
the more Rockchip common sector 0x4000 offset:
SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x200
Because FIT payload is located at sector 0x200 and the TPL+SPL is
located at sector 64, the combined size of TPL+SPL cannot take up more
than 224KiB:
(0x200 - 64) x 512 = 0x38000 (224 KiB)
Adjust SPL_PAD_TO to match the used 0x200 sector offset.
While at it, update the px30-ringneck-u-boot.dtsi to remove the now
unnecessary override of simple-bin:fit:offset since SPL_PAD_TO matches
with the current formula.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
|
|
Since commit 6007b69d544e ("rockchip: rk3399-puma: Update SPL_PAD_TO
Kconfig option"), SPL_PAD_TO matches
(CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR - 64) * 512 and the default
value for simple-bin:fit:offset in rockchip-u-boot.dtsi is
SPL_PAD_TO, so let's remove this override.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
|
|
CONFIG_ENV_OFFSET already defaults to 0x3F8000, however it is stored in
lowercase hexdigits instead of uppercase like in the defconfig.
No change in behavior intended.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
|
|
The default env size is 0x8000 when building for Rockchip SoCs with
support for environment stored in MMC.
Jaguar hasn't entered mass production just yet, so it's a breaking
change we can afford in the name of consistency.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
|
|
ArmSoM Sige7 is a Rockchip RK3588 based SBC (Single Board Computer) by
ArmSoM.
There are two variants depending on the DRAM size : 8G and 16G.
Specification:
Rockchip Rk3588 SoC
4x ARM Cortex-A76, 4x ARM Cortex-A55
8/16GB memory LPDDR4x
Mali G610MC4 GPU
2x MIPI CSI 2 multiple lanes connector
64GB/128GB on board eMMC
uSD slot
1x USB 2.0 Type-A, 1x USB 3.0 Type-A, 1x USB 3.0 Type-C
1x HDMI 2.1 output
2x 2.5 Gbps Ethernet port
40-pin IO header including UART, SPI and I2C
USB PD over USB Type-C
Size: 92mm x 62mm
Kernel commit:
81c828a67c78 (arm64: dts: rockchip: Add ArmSom Sige7 board)
Signed-off-by: Jianfeng Liu <liujianfeng1994@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
After we sync USB3 DRD nodes from v6.10-rc1, these obsolete nodes
can be removed.
Signed-off-by: Jianfeng Liu <liujianfeng1994@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Specification:
Rockchip Rk3588 SoC
4x ARM Cortex-A76, 4x ARM Cortex-A55
8/16/32GB Memory LPDDR4/LPDDR4x
Mali G610MP4 GPU
2× MIPI-CSI Connector
1× MIPI-DSI Connector
1x M.2 Key M (PCIe 3.0 4-lanes)
2x RTL8125 2.5G Ethernet
Onboard AP6275P for WIFI6/BT5
32GB/64GB/128GB eMMC
MicroSD card slot
1x USB2.0, 1x USB3.0 Type-A, 1x US3.0 Type-C
1x HDMI Output, 1x type-C DP Output
Functions work normally:
USB2.0 Host
USB3.0 Type-A Host
M.2 Key M (PCIe 3.0 4-lanes)
2x RTL8125 2.5G Ethernet
eMMC
MicroSD card
More information can be obtained from the following website
https://docs.armsom.org/armsom-sige7
Signed-off-by: Jianfeng Liu <liujianfeng1994@gmail.com>
Reviewed-by: Weizhao Ouyang <weizhao.ouyang@arm.com>
Link: https://lore.kernel.org/r/20240420034300.176920-4-liujianfeng1994@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
[ upstream commit: 81c828a67c78bb03ea75819c417c93c7f3d637b5 ]
(cherry picked from commit d427a11542bcf5364a5260280e077f0a2e030dcb)
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
The mmu600_pcie is connected with the five PCIe controllers.
The mmu600_php is connected with the USB3 controller, the GMAC
controllers, and the SATA controllers.
See 8.2 Block Diagram, in rk3588 TRM (Technical Reference Manual).
The IOMMUs are disabled by default, as further patches are needed to
program the SID/SSIDs in to the IOMMUs.
iommu: Default domain type: Translated
iommu: DMA domain TLB invalidation policy: strict mode
arm-smmu-v3 fc900000.iommu: ias 48-bit, oas 48-bit (features 0x001c1eaf)
arm-smmu-v3 fc900000.iommu: allocated 65536 entries for cmdq
arm-smmu-v3 fc900000.iommu: allocated 32768 entries for evtq
arm-smmu-v3 fc900000.iommu: msi_domain absent - falling back to wired irqs
Additionally, the IOMMU correctly triggers an IOMMU fault when
a PCIe device performs a write (since the device hasn't been
assigned a SID/SSID):
arm-smmu-v3 fc900000.iommu: event 0x02 received:
arm-smmu-v3 fc900000.iommu: 0x0000010000000002
arm-smmu-v3 fc900000.iommu: 0x0000000000000000
arm-smmu-v3 fc900000.iommu: 0x0000000000000000
arm-smmu-v3 fc900000.iommu: 0x0000000000000000
While this doesn't provide much value as is, having the devices as
disabled in the device tree will allow developers to see that the rk3588
actually has IOMMUs on the SoC.
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Link: https://lore.kernel.org/r/20240502140231.477049-2-cassel@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
[ upstream commit: cd81d3a0695cc54ad6ac0ef4bbb67a7c8f55d592 ]
(cherry picked from commit ea9a34aa0d786cbf4b87f1ba528e69b07219738f)
Signed-off-by: Jianfeng Liu <liujianfeng1994@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Add both USB3 dual-role controllers to the RK3588 devicetree.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20240408225109.128953-8-sebastian.reichel@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
[ upstream commit: 33f393a2a990e16f56931ca708295f31d2b44415 ]
(cherry picked from commit c7ed588e14f7dd04a92fb55f12680f94c7b14edf)
Signed-off-by: Jianfeng Liu <liujianfeng1994@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Add both USB3-DisplayPort PHYs to RK3588 SoC DT.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20240408225109.128953-7-sebastian.reichel@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
[ upstream commit: e18e5e8188f2671abf63abe7db5f21555705130f ]
(cherry picked from commit 5110caca9865718616cf7093ed4a9a1bc54780db)
Signed-off-by: Jianfeng Liu <liujianfeng1994@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
