| Age | Commit message (Collapse) | Author |
|---|
|
The name of the pin function was changed last minute in the DT, from
emac0 to gmac0.
Adjust the name we use in the pinctrl driver accordingly.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
|
|
The new DT pinctrl binding would allow us to read the pinmux values from
the DT, but it is actually easier to just continue with hardcoding the
mux values in the driver, and matching them against the "function" name.
Add the values for the primary and secondary pin controller on the A523.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
|
|
The Allwinner A100 SoC has been around for a while, and has now seemingly
been replaced with its close sibling A133.
Add the required mapping between the pinmux group strings and their
respective mux value, as far as used by U-Boot proper. Linux has some
basic (clock and pinctrl) support for a while, so we can build on the
names already used there.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
|
|
sunxi platforms put .bss in DRAM, so .bss is not available in SPL before
DRAM controller initialization. Therefore, this buffer must be placed in
the .data section.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
|
|
This adds the remaining code bits to teach U-Boot about Allwinner's
newest SoC generation. This was introduced with the RISC-V based
Allwinner D1 SoC, which actually shares a die with the ARM cores versions
called R528 (BGA, without DRAM) and T113s (QFP, with embedded DRAM).
This adds the new Kconfig stanza, using the two newly introduced symbols
for the new SoC generation and pincontroller. It also adds the new symbols
to the relavent code places, to set all the hardcoded bits directly.
We need one DT override:
The ARM core version of the DT specifies the CPUX watchdog as
"reserved", which means it won't be recognised by U-Boot. Override this
in our generic sunxi-u-boot.dtsi, to let U-Boot pick up this watchdog,
so that the generic reset driver will work.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
|
|
Apart from using the new pinctrl MMIO register layout, the Allwinner D1
and related SoCs still need to usual set of mux values hardcoded in
U-Boot's pinctrl driver.
Add the values we need so far to this list, so that DM based drivers
will just work without further ado.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
|
|
U-Boot's generic GPIO_EXTRA_HEADER is a convenience symbol to allow code
to more easily include platform specific GPIO headers. This should not
be needed in a DM world anymore, since the generic GPIO framework
handles that nicely.
For Allwinner boards we still need to deal with non-DM GPIO in the SPL,
but this should become the exception, not the rule.
Make this more obvious by removing the definition of GPIO_EXTRA_HEADER,
and just force every legacy user of platform specific GPIO to include
the new sunxi_gpio.h header explicitly. Everyone doing so should feel
ashamed and should find a way to avoid it from now on.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Samuel Holland <samuel@sholland.org>
|
|
So far every Allwinner SoC used the same basic pincontroller/GPIO
register frame, and just differed by the number of implemented banks and
pins, plus some special functionality from time to time. However the D1
and successors use a slightly different pinctrl register layout.
Use that opportunity to drop "struct sunxi_gpio", that described that
MMIO frame in a C struct. That approach is somewhat frowned upon in the
Linux world and rarely used there, though still popular with U-Boot.
Switching from a C struct to a "base address plus offset" approach allows
to switch between the two models more dynamically, without reverting to
preprocessor macros and #ifdef's.
Model the pinctrl MMIO register frame in the usual "base address +
offset" way, and replace a hard-to-parse CPP macro with a more readable
static function.
All the users get converted over. There are no functional changes at
this point, it just prepares the stages for the D1 and friends.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Tested-by: Samuel Holland <samuel@sholland.org>
|
|
NAND is always at function 2 on port C.
Pin lists and mux values were taken from the Linux drivers.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
|
|
P2WI and RSB are used to communicate with a PMIC. Most SoCs have only
one possible pinmux. F1C100s has two possibilities, with different mux
values, so omit it until some board needs one of them.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
|
|
Some boards with the Allwinner F1C100s family SoCs use UART1 for its
debug UART, so define the pins for the SPL and the pinmux name and mux
value for U-Boot proper.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
|
|
Pin lists and mux values were taken from the Linux drivers.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
|
|
This is the only possible mux setting for the A64's PWM peripheral.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
|
|
Pin lists and mux values were taken from the Linux drivers.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
|
|
Where multiple options were available, the one matching board.c and the
device trees was chosen.
Pin lists and mux values were taken from the Linux drivers.
Signed-off-by: Samuel Holland <samuel@sholland.org>
[Andre: fixup H5 I2C1 pinmux]
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
|
|
Pin lists and mux values were taken from the Linux drivers.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
|
|
Pin lists and mux values were taken from the Linux drivers.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
|
|
Pin lists and mux values were taken from the Linux drivers.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
|
|
This includes UART0 and R_UART (s_uart) on all supported platforms, plus
the additional UART configurations from arch/arm/mach-sunxi/board.c.
Pin lists and mux values were taken from the Linux drivers.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
|
|
The sunxi pinctrl hardware has bias and drive control. Add driver
support for configuring those options.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
|
|
The pinmux command uses this function to display pinmux status.
Since the driver cannot map pin numbers to a list of supported
functions, only functions which are common across all pins can be
reported by name.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
|
|
Implement the operations to get pin and function names, and to set the
mux for a pin. The pin count and pin names are calculated as if each
bank has the maximum number of pins. Function names are simply the index
into a list of { function name, mux value } pairs.
We assume all pins associated with a function use the same mux value for
that function. This is generally true within a group of pins on a single
port, but generally false when some peripheral can be muxed to multiple
ports. For example, A64 UART3 uses mux 3 on port D, and mux 2 on port H.
But all of the port D pins use the same mux value, and so do all of the
port H pins. This applies even when the pins for some function are not
contiguous, and when the lower-numbered mux values are unused. A good
example of both of these cases is SPI0 on most SoCs.
This strategy saves a lot of space (which is especially important for
SPL), but where the mux value for a certain function differs across
ports, it forces us to choose a single port for that function at build
time. Since almost all boards use the default (i.e. reference design)
pin muxes[1], this is unlikely to be a problem.
[1]: See commit dda9fa734f81 ("sunxi: Simplify MMC pinmux selection")
Signed-off-by: Samuel Holland <samuel@sholland.org>
[Andre: add comment summarising the commit message]
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
|
|
Create a do-nothing driver for each sunxi pin controller variant.
Since only one driver can automatically bind to a DT node, since the
GPIO driver already requires a manual binding process, and since the
pinctrl driver needs access to some of the same information, refactor
the GPIO driver to be bound by the pinctrl driver. This commit should
cause no functional change.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
|
