| Age | Commit message (Collapse) | Author |
|---|
|
To support PQC container format which is used for post quantum
authentication on new i.MX parts like i.MX94
The major changes compared to legacy container format is in
signature block, new container tag and version, and new alignment
of container header.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
|
|
This patch adds V2X container support for i.MX95. Since V2X container
may not be included in ahab-container.img of i.MX95, check if V2X
container exists in order to get the correct image end.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
|
|
Tim Harvey <tharvey@gateworks.com> says:
Modern eMMC v4+ devices have multiple hardware partitions per the JEDEC
specification described as:
Boot Area Partition 1
Boot Area Partition 2
RPMB Partition
General Purpose Partition 1
General Purpose Partition 2
General Purpose Partition 3
General Purpose Partition 4
User Data Area
These are referenced by fields in the PARTITION_CONFIG register
(Extended CSD Register 179) which is defined as:
bit 7: reserved
bit 6: BOOT_ACK
0x0: No boot acknowledge sent (default
0x1: Boot acknowledge sent during boot operation Bit
bit 5:3: BOOT_PARTITION_ENABLE
0x0: Device not boot enabled (default)
0x1: Boot Area partition 1 enabled for boot
0x2: Boot Area partition 2 enabled for boot
0x3-0x6: Reserved
0x7: User area enabled for boot
bit 2:0 PARTITION_ACCESS
0x0: No access to boot partition (default)
0x1: Boot Area partition 1
0x2: Boot Area partition 2
0x3: Replay Protected Memory Block (RPMB)
0x4: Access to General Purpose partition 1
0x5: Access to General Purpose partition 2
0x6: Access to General Purpose partition 3
0x7: Access to General Purpose partition 4
Note that setting PARTITION_ACCESS to 0x0 results in selecting the User
Data Area partition.
You can see above that the two fields BOOT_PARTITION_ENABLE and
PARTITION_ACCESS do not use the same enumerated values.
U-Boot uses a set of macros to access fields of the PARTITION_CONFIG
register:
EXT_CSD_BOOT_ACK_ENABLE (1 << 6)
EXT_CSD_BOOT_PARTITION_ENABLE (1 << 3)
EXT_CSD_PARTITION_ACCESS_ENABLE (1 << 0)
EXT_CSD_PARTITION_ACCESS_DISABLE (0 << 0)
EXT_CSD_BOOT_ACK(x) (x << 6)
EXT_CSD_BOOT_PART_NUM(x) (x << 3)
EXT_CSD_PARTITION_ACCESS(x) (x << 0)
EXT_CSD_EXTRACT_BOOT_ACK(x) (((x) >> 6) & 0x1)
EXT_CSD_EXTRACT_BOOT_PART(x) (((x) >> 3) & 0x7)
EXT_CSD_EXTRACT_PARTITION_ACCESS(x) ((x) & 0x7)
There are various places in U-Boot where the BOOT_PARTITION_ENABLE field
is accessed via EXT_CSD_EXTRACT_PARTITION_ACCESS and converted to a
hardware partition consistent with the definition of the
PARTITION_ACCESS field used by the various mmc_switch incarnations.
To add some sanity to the distinction between BOOT_PARTITION_ENABLE
(used to specify the active device on power-cycle) and PARTITION_ACCESS
(used to switch between hardware partitions) create two enumerated types
and use them wherever struct mmc * part_config is used or the above
macros are used.
Additionally provide arrays of the field names and allow those to be
used in the 'mmc partconf' command and in board support files.
The first patch adds enumerated types and makes use of them which
represents no compiled code change.
The 2nd patch adds the array of names and uses them in the 'mmc
partconf' command.
The 3rd patch uses the array of hardware partition names in a board
support file to show what emmc hardware partition U-Boot is being loaded
from.
|
|
Modern eMMC v4+ devices have multiple hardware partitions per the JEDEC
specification described as:
Boot Area Partition 1
Boot Area Partition 2
RPMB Partition
General Purpose Partition 1
General Purpose Partition 2
General Purpose Partition 3
General Purpose Partition 4
User Data Area
These are referenced by fields in the PARTITION_CONFIG register
(Extended CSD Register 179) which is defined as:
bit 7: reserved
bit 6: BOOT_ACK
0x0: No boot acknowledge sent (default
0x1: Boot acknowledge sent during boot operation Bit
bit 5:3: BOOT_PARTITION_ENABLE
0x0: Device not boot enabled (default)
0x1: Boot Area partition 1 enabled for boot
0x2: Boot Area partition 2 enabled for boot
0x3-0x6: Reserved
0x7: User area enabled for boot
bit 2:0 PARTITION_ACCESS
0x0: No access to boot partition (default)
0x1: Boot Area partition 1
0x2: Boot Area partition 2
0x3: Replay Protected Memory Block (RPMB)
0x4: Access to General Purpose partition 1
0x5: Access to General Purpose partition 2
0x6: Access to General Purpose partition 3
0x7: Access to General Purpose partition 4
Note that setting PARTITION_ACCESS to 0x0 results in selecting the User
Data Area partition.
You can see above that the two fields BOOT_PARTITION_ENABLE and
PARTITION_ACCESS do not use the same enumerated values.
U-Boot uses a set of macros to access fields of the PARTITION_CONFIG
register:
There are various places in U-Boot where the BOOT_PARTITION_ENABLE field
is accessed via EXT_CSD_EXTRACT_PARTITION_ACCESS and converted to a
hardware partition consistent with the definition of the
PARTITION_ACCESS field which is also the value used to specify the
hardware partition of the various mmc_switch incarnations.
To add some sanity to the distinction between BOOT_PARTITION_ENABLE
(used to specify the active device on power-cycle) and PARTITION_ACCESS
(used to switch between hardware partitions) create two enumerated types
and use them wherever struct mmc * part_config is used or the above
macros are used.
This represents no code changes.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
|
|
As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Remove <common.h> from all mach-imx, CPU specific sub-directories and
include/asm/arch-mx* files and when needed add missing include files
directly.
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
The spl_spi_get_uboot_offs weak function is defined unsigned int.
Signed-off-by: Ye Li <ye.li@nxp.com>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-imx
u-boot-imx-20231024
-------------------
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/18211
- Fixes for MC2432 Eeprom
- i.MX93 ADC
- Secondary boot mode on i.MX8M
|
|
Make sure we have an IMX header before calling spl_load_imx_container,
since if we don't it will fail with -ENOENT. This allows us to fall back to
legacy/raw images if they are also enabled.
This is a functional change, one which likely should have been in place
from the start, but a functional change nonetheless. Previously, all
non-IMX8 images (except FITs without FIT_FULL) would be optimized out if
the only image load method enabled supported IMX8 images. With this change,
support for other image types now has an effect.
There are seven boards with SPL_LOAD_IMX_CONTAINER enabled: three with
SPL_BOOTROM_SUPPORT:
imx93_11x11_evk_ld imx93_11x11_evk imx8ulp_evk
and four with SPL_MMC:
deneb imx8qxp_mek giedi imx8qm_mek
All of these boards also have SPL_RAW_IMAGE_SUPPORT and
SPL_LEGACY_IMAGE_FORMAT enabled as well. However, none have FIT support
enabled. Of the six load methods affected by this patch, only SPL_MMC and
SPL_BOOTROM_SUPPORT are enabled with SPL_LOAD_IMX_CONTAINER.
spl_romapi_load_image_seekable does not support legacy or raw images, so
there is no growth. However, mmc_load_image_raw_sector does support loading
legacy/raw images. Since these images could not have been booted before, I
have disabled support for legacy/raw images on these four boards. This
reduces bloat from around 800 bytes to around 200.
There are no in-tree boards with SPL_LOAD_IMX_CONTAINER and AHAB_BOOT both
enabled, so we do not need to worry about potentially falling back to
legacy images in a secure boot scenario.
Future work could include merging imx_container.h with imx8image.h, since
they appear to define mostly the same structures.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
|
|
Add a function to abstract the common task of validating i.MX8 container
image headers.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
|
|
Introduce two new weak functions, arch_spl_mmc_get_uboot_raw_sector() and
board_spl_mmc_get_uboot_raw_sector(), each of which can be overridden at
a matching level, that is arch/ and board/ , in addition to the existing
weak function spl_mmc_get_uboot_raw_sector().
This way, architecture code can define a default architecture specific
implementation of arch_spl_mmc_get_uboot_raw_sector(), while the board
code can override that using board_spl_mmc_get_uboot_raw_sector() which
takes precedence over the architecture code. In some sort of unlikely
special case where code has to take precedence over board code too, the
spl_mmc_get_uboot_raw_sector() is still left out to be a weak function,
but it should be unlikely that this is ever needed to be overridden.
Signed-off-by: Marek Vasut <marex@denx.de>
|
|
Add the support for loading image from secondary container set on
iMX8QM B0, iMX8QXP C0.
Using the SCFW API to get container set index, if it is the secondary
boot, get the offset from fuse and apply to offset of current container
set beginning for loading.
Also override the emmc boot partition to check secondary boot and switch
to the other boot part.
This patch is modified from NXP downstream:
imx8: Fix the fuse used by secondary container offset
imx: container: Skip container set check for ROM API
imx8: spl: Support booting from secondary container set
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Checking container header tag and version is wrong, it causes to fail
to bypass invalid container
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
We did not add a prototype for spl_mmc_get_uboot_raw_sector to
include/spl.h before, so add and document one now. Correct the incorrect
prototype in board/advantech/imx8mp_rsb3720a1/imx8mp_rsb3720a1.c and
ensure that we have spl.h where we define a non-weak
spl_mmc_get_uboot_raw_sector as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS namespace do
not easily transition to Kconfig. In many cases they likely should come
from the device tree instead. Move these out of CONFIG namespace and in
to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Rename these options so that CONFIG_IS_ENABLED can be used with them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
[trini: Fixup some incorrect renames]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
When booting from boot part1/2, the image offset should be 0, but
ROM has a bug to return 0x8000. Has to workaround the issue before
ROM fix it.
Use a ROM function to know boot from emmc boot part or user part
So we can set the image offset accordingly.
Signed-off-by: Ye Li <ye.li@nxp.com>
|
|
i.MX8ULP support using ROM API to load container image,
it use same ROM API as i.MX8MN/MP, and use same container format
as i.MX8QM/QXP.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Since the container is shared among i.MX platforms, move its header file
to mach-imx
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Since we will re-use the container parser on imx8ulp, move the codes
to mach-imx
Signed-off-by: Ye Li <ye.li@nxp.com>
|
