| Age | Commit message (Collapse) | Author |
|---|
|
Add STM32MP23 support which is a cost optimized of STM32MP25.
More details available at:
https://www.st.com/en/microcontrollers-microprocessors/stm32mp2-series.html
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
Add hardware initialization for the STM32MP13xx in SPL. This is
similar to STM32MP15xx except the code has to enable MCE to bring
DRAM controller up later.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Marek Vasut <marek.vasut@mailbox.org>
|
|
The DBGMCU block is available at address 0x50081000 both on STM32MP13xx
and on STM32MP15xx . There is no reason to limit the DBGMCU macro being
set only on STM32MP15xx , remove the ifdeffery.
Signed-off-by: Marek Vasut <marek.vasut@mailbox.org>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
The STM32MP13xx has only 128 kiB of SYSRAM starting at address 0x2ffe0000 .
The STM32MP15xx has 256 kiB of SYSRAM starting at address 0x2ffc0000 . Make
sure both SoCs configure ARMV7_SECURE_BASE correctly . Define the SYSRAM
base in stm32.h to be consistent with the STM32MP15xx macro.
Signed-off-by: Marek Vasut <marek.vasut@mailbox.org>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
The STM32MP25 revision ID are now defined with the OTP102, this patch
implements this new system.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Patrice CHOTARD <patrice.chotard@foss.st.com>
|
|
Add support of all the boot mode supported by STM32MP25x family
with information provided by TF-A in backup register
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
"#if" was used instead of "#ifdef"
Fixes: 01a701994b05 ("stm32mp2: initial support")
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
|
CONFIG options must not use lower-case letter. Convert this and related
ones to upper case.
Signed-off-by: Simon Glass <sjg@chromium.org
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
CONFIG options must not use lower-case letter. Convert this and related
ones to upper case.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@foundries.io>
|
|
Activate the command stboard for stm32mp25 STMicroelectronics boards,
add the default used OTP identifier and the associated board identifier:
- stm32mp25xx-ev1 = MB1936
- stm32mp25xx-dk = MB1605
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
Add support of BSEC for STM32MP25x family to access OTP.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
|
Prepare v2024.01-rc3
|
|
https://source.denx.de/u-boot/custodians/u-boot-stm into next
Introduce STM32MP2 SoCs family support
Add STM32MP257F-EV1 board
[trini: Adjust some includes]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Add initial support for STM32MP2 SoCs family.
SoCs information are available here :
https://www.st.com/content/st_com/en/campaigns/microprocessor-stm32mp2.html
Migrate all MP1 related code into stm32mp1/ directory
Create stm32mp2 directory dedicated for STM32MP2 SoCs.
Common code to MP1, MP13 and MP25 is kept into
arch/arm/mach-stm32/mach-stm32mp directory :
- boot_params.c
- bsec
- cmd_stm32key
- cmd_stm32prog
- dram_init.c
- syscon.c
- ecdsa_romapi.c
For STM32MP2, it also :
- adds memory region description needed for ARMv8 MMU.
- enables early data cache before relocation.
During the transition before/after relocation, the MMU, initially setup
at the beginning of DDR, must be setup again at a correct address after
relocation. This is done in enables_caches() by disabling cache, force
arch.tlb_fillptr to NULL which will force the MMU to be setup again but
with a new value for gd->arch.tlb_addr. gd->arch.tlb_addr has been
updated after relocation in arm_reserve_mmu().
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
|
Obtain from TAMP backup register information about image authorization
status and partition id used for booting. Store this info in
environmental variables ("boot_auth" and "boot_part" correspondingly).
Image authorization supported values:
0x0 - No authentication done
0x1 - Authentication done and failed
0x2 - Authentication done and succeeded
These values are stored to TAMP backup register by Trusted Firmware-A [1].
Testing:
STM32MP> print boot_part
boot_part=1
STM32MP> print boot_auth
boot_auth=2
[1] https://git.trustedfirmware.org/TF-A/trusted-firmware-a.git/commit/?h=refs/heads/integration&id=ab2b325c1ab895e626d4e11a9f26b9e7c968f8d8
Signed-off-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Co-developed-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
In case the IWDG is enabled by either U-Boot or Linux, the IWDG can never
be disabled again. That includes low power states, which means that if the
IWDG is enabled, the SoC would reset itself after a while in suspend via
the IWDG. This is not desired behavior.
It is possible to enable IWDG pre-timeout IRQ which is routed into the EXTI,
and use that IRQ to wake the CPU up before the IWDG timeout is reached and
reset is triggered. This pre-timeout IRQ can be used to reload the WDT and
then suspend the CPU again every once in a while.
Implement this functionality for both IWDG1 and IWDG2 by reading out all
the unmasked IRQs, comparing the list with currently pending IRQs in GICv3:
- If any IRQ is pending and it is NOT IWDG1 or IWDG2 pre-timeout IRQ,
wake up and let OS handle the IRQs
- If IWDG1 or IWDG2 IRQ is pending and no other IRQ is pending,
ping the respective IWDG and suspend again
This does not seem to have any adverse impact on power consumption in suspend.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
|
The FWU Multi Bank Update feature allows the platform to boot the
firmware images from one of the partitions(banks). The first stage
bootloader(fsbl) passes the value of the boot index, i.e. the bank
from which the firmware images were booted from to U-Boot. On the
STM32MP157C-DK2 board, this value is passed through one of the SoC's
backup register. Add a function to read the boot index value from the
backup register.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Etienne Carriere <etienne.carriere@linaro.org>
|
|
Depending on backup register value, U-Boot SPL maintains the debug unit
powered-on for debugging purpose; only BUCK1 is required for powering
the debug unit, so revert the setting for all the other power lanes,
except BUCK3 that has to be always on.
To be functional this patch requires a modification in the debugger
,openocd for example, to update the STM32MP15 backup register when it is
required to debug SPL after reset. After deeper analysis this behavior
will be never supported in tools so the associated code, will be never
used and the associated code can be removed.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
Introduce the code in mach-stm32mp and the configuration file
stm32mp13_defconfig for the new STM32MP family.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
Implement PSCI system suspend and placement of DRAM into SSR while the
CPUs are in suspend. This saves non-trivial amount of power in suspend,
on 2x W632GU6NB-15 ~710mW.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
Use the device sequence number in boot_instance variable
and no more the SDMMC instance provided by ROM code/TF-A.
After this patch we don't need to define the mmc alias in
device tree, for example:
mmc0 = &sdmmc1;
mmc1 = &sdmmc2;
mmc2 = &sdmmc3;
to have a correct mapping between the ROM code boot device =
"${boot_device}${boot_instance}" and the MMC device in U-Boot.
With this patch the 'mmc0' device (used in mmc commands) is
always used when only one instance sdmmc is activated in device
tree, even if it is only the sdmmc2 or sdmmc3.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
Move this uncommon header out of the common header.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Some places use __ASSEMBLER__ instead which does not work since the
Makefile does not define it. Fix them.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Manage BOOT_FLASH_SPINAND, with boot_device="spi-nand"
and treat this value in bootcmd_stm32mp.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Define FMC2 base address, for use in board files, until there is an
actual FMC2 bus driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Add BSEC lock access (read / write) at 0xC0000000 offset of misc driver.
The write access only available for Trusted boot mode, based on new
SMC STM32_SMC_WRLOCK_OTP.
With the fuse command, the permanent lock status is accessed with
0x10000000 offset (0xC0000000 - 0x8000000 for OTP sense/program
divided by u32 size), for example:
Read lock status of fuse 57 (0x39)
STM32MP> fuse sense 0 0x10000039 1
Sensing bank 0:
Word 0x10000039: 00000000
Set permanent lock of fuse 57 (0x39)
STM32MP> fuse prog 0 0x10000039 1
Sensing bank 0:
Word 0x10000039: 00000000
WARNING: the OTP lock is updated only after reboot
WARING: Programming lock or fuses is an irreversible operation!
This may brick your system.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Update the driver to use the latest binding from kernel v5.5-rc1:
no more use syscon or regmap to access to pwr register and
only one pwr_regulators node with the compatibility "st,stm32mp1,pwr-reg"
is available.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Use the backup register #17 as coprocessor resource table address and
backup register #18 as coprocessor state.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Depending on backup register value, we maintain the debug unit
powered-on for debugging purpose.
Only BUCK1 is required for powering the debug unit, so revert
the setting for all the other power lanes, except BUCK3 that
has to be always on.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Reduce difference with kernel Linux device tree.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Support for ETZPC is removed as this device is not present
in Linux kernel device tree.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Activate bootcount and use TAMP register to store the count value.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Update bsec driver to use the device tree provided by Kernel.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Add SYSCON driver for syscfg and etpzc and reorder in alphabetics order
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
The boot mode can be forced by key press
or by TAMP register, requested in kernel by syscon-reboot-mode
tamp: tamp@5c00a000 {
compatible = "simple-bus", "syscon", "simple-mfd";
reg = <0x5c00a000 0x400>;
reboot-mode {
compatible = "syscon-reboot-mode";
offset = <0x150>; /* reg20 */
mask = <0xff>;
mode-normal = <0>;
mode-fastboot = <0x1>;
mode-recovery = <0x2>;
mode-stm32cubeprogrammer = <0x3>;
mode-ums_mmc0 = <0x10>;
mode-ums_mmc1 = <0x11>;
mode-ums_mmc2 = <0x12>;
};
};
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
- export the function get_bootmode() and reused it in spl code
- manage uart instance by alias (prepare v4.19 binding)
- solve issue on nand instance
- restore console for uart boot
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Implement checkboard() function to display
- the boot chain used: basic or trusted
- the board compatible in device tree
- the board identifier and revision, saved in OTP59 for ST boards
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Add a MISC driver with read and write access to BSEC IP
(Boot and Security and OTP control)
- offset 0: shadowed values
- offset 0x80000000: OTP fuse box values (SAFMEM)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Add the needed information to enable the debug uart
to have printf before the serial driver probe
(so before probe for clock, pincontrol and reset drivers)
To enable the debug on uart 4 (default console):
+ CONFIG_DEBUG_UART=y
+ CONFIG_DEBUG_UART_STM32=y
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
This driver binds and manages the following regulator of
SoC's PWR block :
- reg11
- reg18
- usb33
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Add PSCI v1.0 support for Linux and manage PSCI state
for each CPU (affinity 0 level) with all mandatory functions:
- PSCI_VERSION
- CPU_SUSPEND
- CPU_OFF
- CPU_ON
- AFFINITY_INFO
- SYSTEM_OFF
- SYSTEM_RESET
- PSCI_FEATURES
and 1 optional to avoid Linux warning
- MIGRATE_INFO_TYPE
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: CITOOLS <smet-aci-reviews@lists.codex.cro.st.com>
|
|
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have multiple licenses (in
these cases, dual license) declared in the SPDX-License-Identifier tag.
In this case we change from listing "LICENSE-A LICENSE-B" or "LICENSE-A
or LICENSE-B" or "(LICENSE-A OR LICENSE-B)" to "LICENSE-A OR LICENSE-B"
as per the Linux Kernel style document. Note that parenthesis are
allowed so when they were used before we continue to use them.
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Add STGEN as SYSCON device: allow access to device address
defined in device tree
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
SPL copy BootRom boot mode information
in TAMP register 21.
This TAMP register information is used
after relocation to set 2 env variables
- boot_device
- boot_instance
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
- add new arch stm32mp for STM32 MPU/Soc based on Cortex A
- support for stm32mp157 SOC
- SPL is used as first boot stage loader
- using driver model for all the drivers, even in SPL
- all security feature are deactivated (ETZC and TZC)
- reused STM32 MCU drivers when it is possible
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
