Age | Commit message (Collapse) | Author |
|
Use consistent lowercase hex prefix style in arch/*
Signed-off-by: E Shattow <e@freeshell.de>
|
|
Add native support of the bootcount mechanism in the ZynqMP by
utilising internal PMU registers. The Persistent Global Storage
Registers of the Platform Management Unit can keep their value
during reboot cycles unless there is a POR reset, making them
appropriate for the bootcount mechanism.
Signed-off-by: Vasileios Amoiridis <vasileios.amoiridis@cern.ch>
Reviewed-by: Heiko Schocher <hs@denx.de>
Link: https://lore.kernel.org/r/20241105132744.1572759-2-vassilisamir@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
|
|
Set NIDEN, enabling non-invasive debug for the CCI-400 PMU. Otherwise,
the PMU is effectively disabled.
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20240905171833.325548-3-sean.anderson@linux.dev
Signed-off-by: Michal Simek <michal.simek@amd.com>
|
|
Boot devices (QSPI, MMC, NAND, and Ethernet) use secure access for DMA
by default. As this causes problems when using the SMMU [1], configure
them for normal access instead.
[1] https://support.xilinx.com/s/article/72164
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Link: https://lore.kernel.org/r/20240905171833.325548-2-sean.anderson@linux.dev
Signed-off-by: Michal Simek <michal.simek@amd.com>
|
|
To boot into the firmware recovery tool, the user currently
needs to press a button on the board while powering the
system up. To simplify this process, a U-Boot command
was added to allow booting directly into the recovery tool.
For example:
ZynqMP> zynqmp reboot <multiboot offset in hex>
Co-develop-by: Prasad Kummari <prasad.kummari@amd.com>
Signed-off-by: Prasad Kummari <prasad.kummari@amd.com>
Co-develop-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20240827115529.2931334-1-prasad.kummari@amd.com
|
|
Currently the pcap_prog struct variable is pointing to 0x3004 which is
incorrect according to [1]. The variable should point to 0x3000.
[1] https://www.xilinx.com/htmldocs/registers/ug1087/ug1087-zynq-ultrascale-registers.html#csu___pcap_prog.html
Signed-off-by: Lukas Funke <lukas.funke@weidmueller.com>
Link: https://lore.kernel.org/r/20230915093901.1062825-1-lukas.funke-oss@weidmueller.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
|
|
Update my and DPs email address to match current setup.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/aba5b19b9c5a95608829e86ad5cc4671c940f1bb.1688992543.git.michal.simek@amd.com
|
|
When Linux boot takes over control of the pmu
(by signaling PM_INIT_FINALIZE via ipi), pmu will switch off 'unused'
rpu cores. The Xilinx zynqmp fsbl prevents switching off those cores by
marking rpu cores as 'used' when loading code partitions to those cores.
The current u-boot SPL is missing this behaviour, which results in
halting rpu cores during Linux boot.
This commit mimics the xilinx zynqmp fsbl behavior by marking r5 cores as
used when they are released during boot.
Signed-off-by: Lukas Funke <lukas.funke@weidmueller.com>
Signed-off-by: Lukas Funke <lukas.funke-oss@weidmueller.com>
Link: https://lore.kernel.org/r/20221028121547.26464-2-lukas.funke-oss@weidmueller.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
|
|
Output the secure boot configuration to the console.
Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Link: https://lore.kernel.org/r/20211013170447.10414-1-jorge@foundries.io
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
When boot.bin is configured for secure boot the CSU will disable the
JTAG interface on all cases.
Some boards might rely on this interface for flashing to QSPI in which
case those systems might end up bricked during development.
This commit will restore the interface under CSU control
Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Link: https://lore.kernel.org/r/20211013134800.19452-1-jorge@foundries.io
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
soc_xilinx_zynqmp driver allows identification of family & revision
of zynqmp SoC. This driver is selected by CONFIG_SOC_XILINX_ZYNQMP.
Add this config to xilinx_zynqmp_virt_defconfig file.
Probe this driver using platdata U_BOOT_DEVICE structure which is
specified in mach-zynqmp/cpu.c.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Reviewed-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Use the ZDMA channel 0 to initialize the DRAM banks. This avoid
spurious ECC errors that can occur when accessing unitialized memory.
The feature is enabled by setting the option
CONFIG_SPL_ZYNQMP_DRAM_ECC_INIT and providing the following data:
SPL_ZYNQMP_DRAM_BANK1_BASE: start of memory to initialize
SPL_ZYNQMP_DRAM_BANK1_LEN : len of memory to initialize (hex)
SPL_ZYNQMP_DRAM_BANK2_BASE: start of memory to initialize
SPL_ZYNQMP_DRAM_BANK2_LEN : len of memory to initialize (hex)
Setting SPL_ZYNQMP_DRAM_BANK_LEN to 0 takes no action.
Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
The default register configuration after powerup for PSSYSMON_ANALOG_BUS
register is incorrect. Hence, fix this in SPL by writing correct fixed
value. It follows UG1085 chapter 'PS SYSMON Analog_Bus' and reflects commit
sw_apps:zynq ("056ca65d44549ce27f716d423e8dfdefeee7440c")
in Xilinx:embeddedsw[1].
[1] https://github.com/Xilinx/embeddedsw
Signed-off-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Both Zynq and ZynqMP can show silicon versions in SPL boot flow. It is
useful to be aware.
The patch is also fixing possition of these bits on ZynqMP.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
There is no reason to have these macros. But record offsets of missing
register in the structure for future use.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Move this uncommon header out of the common header.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Multi boot register can be used for using different boot images and design
better boot strategy. Let EL3 SPL or U-Boot to read it and print it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Remove hardcoded base address of nand and replace it with the
value taken from device tree. Remove base address from header
file too.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
All platforms have been converted to DM that's why there is no reason to
keep addresses in headers. They are all read from DT now.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
|
|
With DM in place there is no need to have GEM addresses in headers. None
is using them.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Similar changes was done for Zynq in past and this patch just follow
this pattern to separate cpu code from SoC code.
Move arch/arm/cpu/armv8/zynqmp/* -> arch/arm/mach-zynqmp/*
And also fix references to these files.
Based on
"ARM: zynq: move SoC sources to mach-zynq"
(sha1: 0107f2403669f764ab726d0d404e35bb9447bbcc)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|