| Age | Commit message (Collapse) | Author |
|---|
|
mtk_eth.c contains not only the ethernet GMAC/DMA driver, but also
some ethernet switch initialization code. As we may add more switch
support in the future, it's better to move them out of mtk_eth.c to
avoid increasing the code complexity.
Since not all switches are supported for a particular board, Kconfig
options are added to allow user to select which switch should be
built into u-boot. If multiple switches are selected, auto-detecting
can also be enabled.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
|
|
MT7629 need extra setting for gmac2 to work. So additional
capability is added for mt7629 to handle this case.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
|
|
Unlike other platforms, mt7622 has only one SGMII and it can be
attached to either gmac1 or gmac2. So the register field of the
sgmii selection differs from other platforms as newer platforms can
control each sgmii individually.
This patch adds a new capability for mt7622 to handle this case.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
|
|
The SYSCFG0 should be SYSCFG1 according to the programming guide.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
|
|
The register field for SGMII speed selection is a 2-bit field with
value 0 for 1Gbps and 1 for 2.5Gbps (2/3 are reserved).
So it's necessary to set both bits instead of just setting/clearing
only the lower bit.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
|
|
This patch add XGMII support for connecting 2.5G PHY.
Signed-off-by: Bo-Cun Chen <bc-bocun.chen@mediatek.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
|
|
User can assign a specific MDC speed to the eth node as follow:
ð {
...
phy-mode = "usxgmii";
phy-handle = <&phy8>;
mdio {
clock-frequency = <10500000>;
};
phy8: eth-phy@8 {
compatible = "ethernet-phy-id31c3.1c12";
...
};
Signed-off-by: Bo-Cun Chen <bc-bocun.chen@mediatek.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
|
|
This patch adds support for MediaTek MT7988.
MT7988 features MediaTek NETSYS v3, including three GMACs, and two
of them supports 10Gbps USXGMII.
MT7988 embeds a MT7531 switch (not MCM) which supports accessing
internal registers through MMIO instead of MDIO.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
|
|
This patch adds support for NETSYS v3 hardware.
Comparing to NETSYS v2, NETSYS v3 has three GMACs.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
|
|
This patch adds support for USXGMII of SoC.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
|
|
MT7981 has its GMAC2 PHY shared with USB3. To enable GMAC2, mux
register must be set to connect the SGMII phy to GMAC2.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
|
|
Existing SGMII support of mtk-eth is actually a MediaTek-specific
2.5Gbps high-speed SGMII (HSGMII) which does not support
auto-negotiation mode.
This patch adds SGMII 1Gbps auto-negotiation mode and rename the
existing HSGMII to 2500basex.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
|
|
This patch adds support for MediaTek MT7981 and MT7986. Both chips uses
PDMA v2.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
|
|
This patch adds support for PDMA v2 hardware. The PDMA v2 has extended the
DMA descriptor to 8-words, and some of its fields have changed comparing
to the v1 hardware.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
|
|
This patch is a preparation for adding a new version of PDMA of which the
DMA descriptor fields has changed. Using bitfields will result in a complex
modification. Convert bitfields to u32 units can solve this problem easily.
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
|
|
Using a single soc id to control different initialization and TX/RX flow
for all SoCs is not extensible if more hardware variations are added in
the future.
This patch introduces a struct to replace the original mtk_soc to allow
the driver be able handle newer hardwares.
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
|
|
The sgmii mode init flow is almost the same for all mediatek SoC, the
only difference is the register offset(SGMSYS_GEN2_SPEED) is 0x2028
in the old chip(mt7622) but changed to 0x128 for the newer chip(mt7629
and the following chips).
Signed-off-by: MarkLee <Mark-MC.Lee@mediatek.com>
|
|
Move this uncommon header out of the common header.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
mt7531 is a 7-ports switch with 5 embedded giga phys, and uses the same
MAC design of mt7530. The cpu port6 supports SGMII only. The cpu port5
supports RGMII or SGMII in different model.
mt7531 is connected to mt7622 via both RGMII and SGMII interfaces.
In this patch, mt7531 cpu port5 or port6 is configured to maximum
capability to align CPU MAC setting.
The dts has been committed in the commit 6efa450565cdc ("arm: dts:
mediatek: add ethernet and sgmii dts node for mt7622")
Signed-off-by: Landen Chao <landen.chao@mediatek.com>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
|
|
This patch add sgmii init part for the mediatek SoC that
support sgmii mode. It is a must for mt7622.
Signed-off-by: MarkLee <Mark-MC.Lee@mediatek.com>
|
|
This patch adds ethernet support for Mediatek ARM-based SoCs, including
a minimum setup of the integrated switch.
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Mark Lee <Mark-MC.Lee@mediatek.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Tested-By: "Frank Wunderlich" <frank-w@public-files.de>
|
