Age | Commit message (Collapse) | Author |
|
The Renesas R9A07G044L (RZ/G2L) SoC includes two Gigabit Ethernet
interfaces which can be supported using the ravb driver. Some RZ/G2L
specific steps need to be taken during initialization due to differences
between this SoC and previously supported SoCs. We also need to ensure
that the module reset is de-asserted after the module clock is enabled
but before any Ethernet register reads/writes take place.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
|
|
In order to add support for the Renesas RZ/G2L Ethernet IP in a
subsequent patch, we introduce optional de-assertion and re-assertion of
a reset signal in ravb_probe() and ravb_remove().
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
|
|
In order to add support for the Renesas RZ/G2L Ethernet IP in a
subsequent patch, we move all R-Car specific code into new functions and
introduce a device_ops function pointer table.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
|
|
Correctly handle RX errors in ravb_recv() by returning 0 instead
of -EAGAIN on RX error.
In case the RAVB driver detects an RX error in ravb_recv(), it must
not return the -EAGAIN, but instead must return 0. Both error codes
are handled in eth-uclass.c eth_rx() and -EAGAIN is rewritten to 0
at the end of eth_rx(), but negative return code from the .recv()
callback does not trigger .free_pkt() callback, which would clean
up and re-enqueue the descriptor which holds the currently received
corrupted packet. The .free_pkt() must be called for this descriptor,
otherwise the follow up received data become corrupted too, even if
those packets are correctly received. Returning 0 from the .recv()
callback assures the corrupted packet is not processed by the network
stack, but is skipped instead.
For TFTP loading, an RX error produces the timeout "T" output and
resumes the TFTP loading operation shortly afterward, without any
data corruption.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
|
|
In ravb_probe(), we were missing a couple of things in the error
handling path:
* We must unregister the MDIO bus before freeing the corresponding
struct mii_dev instance to avoid the potential for use-after-free
bugs.
* We must free the resources acquired by clk_get_bulk() even if the
clocks have not yet been enabled.
Fixes: 8ae51b6f324e ("net: ravb: Add Renesas Ethernet RAVB driver")
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
|
The value written to the RFLR register includes the length of the CRC
data at the end of each Ethernet frame. So we need to increase the value
written to this register to ensure that we can receive full size frames.
While we're here we can also copy the improved comment from the Linux
kernel.
Fixes: 8ae51b6f324e ("net: ravb: Add Renesas Ethernet RAVB driver")
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> # Fix comment
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
|
Use mdio_alloc() again to allocate MDIO bus. This is possible
because all the miiphybb parameters and ops passing is handled in
at bb_miiphy_read()/bb_miiphy_write() level.
This also fixes previously missed bb_miiphy_free() in .remove
callback of this driver. which does not pose a problem anymore.
Fixes: 079eaca6e7b4 ("net: ravb: Allocate bb_miiphy using bb_miiphy_alloc() and fill in callbacks")
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
|
|
Remove the priv member from struct bb_miiphy_bus and its assignment
from drivers. This turns struct bb_miiphy_bus int struct mii_dev
wrapper, to be cleaned up next.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
|
|
Access to MDIO bus private data can be provided by both
struct mii_dev .priv member and struct bb_miiphy_bus .priv
member, use the former directly and remove .priv from the
later. Drop unused bb_miiphy_getbus(). This removes any
dependency on struct bb_miiphy_bus from the miiphybb code,
except for helper functions which will be removed later.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
|
|
The access to struct bb_miiphy_bus_ops via ops pointer in
struct bb_miiphy_bus is not necessary with wrappers added
in previous patch. Pass the ops pointer directly to both
bb_miiphy_read() and bb_miiphy_write() functions.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
|
|
Do not call bb_miiphy_read()/bb_miiphy_write() accessors directly
in drivers, instead call them through wrapper functions. Those are
meant to be used as function parameter adaptation layer between
struct mii_dev callback function parameters and what the miiphybb
does expect and will soon expect. This is a preparatory patch, no
functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
|
|
Move miiphybb operations into separate struct bb_miiphy_bus_ops
structure, add pointer to struct bb_miiphy_bus_ops into the base
struct bb_miiphy_bus and access the ops through this pointer in
miiphybb generic code. The variable reshuffling in miiphybb.c
cannot be easily avoided.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
|
|
Neither bb_miiphy_buses nor bb_miiphy_buses_num are used anymore.
Drop both of them.
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
|
Instead of doing another lookup, trivially access the struct mii_dev
embedded in struct bb_miiphy_bus . No functional change.
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
|
The struct bb_miiphy_bus embeds struct struct mii_dev, which
already contains one copy of name field. Drop the duplicate
top level copy of name field.
The a38x code does static assignment of disparate names, use
snprintf(...) to fill in matching name in probe to avoid any
breakage.
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
|
Allocate bb_miiphy using bb_miiphy_alloc() and fill in callbacks
currently listed in bb_miiphy_buses[] array. This is a temporary
duplication of assignment to avoid breakage, which will be removed
in follow up patches. At this point, the bb_miiphy callbacks can
reach these accessors by doing container_of() on struct mii_dev.
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
|
Move the bb_miiphy functions before MDIO registration. This is a
preparatory patch, the functions will be referenced around the MDIO
registration in the follow up patches. No functional change.
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
|
The init function does nothing, the bb_miiphy_init() already checks
whether the .init callback is assigned, and if not, skips calling it.
Remove the empty init function. The entire init callback will be
removed in follow up patches.
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
|
These functions can be static as they are referenced only in this file.
Make them static. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
|
|
We can call dev_read_u32_default() instead of calling fdt_getprop() then
fdt32_to_cpu().
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
|
As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Remove <common.h> from this driver directory and when needed
add missing include files directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Rename RMOBILE_CPU_TYPE_* to RENESAS_CPU_TYPE_* because all
the chips are made by Renesas, while only a subset of them is
from the R-Mobile line.
Use the following command to perform the rename:
"
$ git grep -l '\<RMOBILE_CPU_TYPE_[A-Z0-9]\+\>' | \
xargs -I {} sed -i 's@\<RMOBILE\(_CPU_TYPE_[A-Z0-9]\+\)\>@RENESAS\1@g' {}
"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
|
|
Rename rmobile_get_cpu_type() to renesas_get_cpu_type() because
all the chips are made by Renesas, while only a subset of them
is from the R-Mobile line.
Use the following command to perform the rename:
"
$ git grep -l '\<rmobile_get_cpu_type\>' | \
xargs -I {} sed -i 's@\<rmobile_get_cpu_type\>@renesas_get_cpu_type@g' {}
"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
|
|
The common code is now capable of handling reset GPIO associated
with PHY. Drop the local ad-hoc code in favor of common code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
|
|
Add support for R-Car Gen4 SoCs and a matching DT compatible.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Drop SoC specific compatible, use RCAR_64 Kconfig symbol, update commit message]
|
|
Calling old U-Boot API doesn't allow to use fixed PHY.
Searching by mask is the part of new function, after
scanning FDT for a fixed PHY definition
Fixes: e821a7bdb13 ("net: ravb: Detect PHY correctly")
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Mikhail Lappo <mikhail.lappo@esrlabs.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
[Hai Pham: Drop phy_connect_dev since it's called in phy_connect]
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Use mask -1 instead of 0 to reinstate the search behavior
over all PHY addresses. Add Fixes tag, sort the tag list.]
|
|
The current set of U-Boot upstream R-Car Gen3 DTs all contain generic
"renesas,etheravb-rcar-gen3" compatible strings, drop the SoC specific
compatible string support from U-Boot to reduce size and duplication.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
|
Currently we require PHY interface mode to be known when
finding/creating the PHY - the functions
* phy_connect_phy_id()
* phy_device_create()
* create_phy_by_mask()
* search_for_existing_phy()
* get_phy_device_by_mask()
* phy_find_by_mask()
all require the interface parameter, but the only thing done with it is
that it is assigned to phydev->interface.
This makes it impossible to find a PHY device without overwriting the
set mode.
Since the interface mode is not used during .probe() and should be used
at first in .config(), drop the interface parameter from these
functions. Make the default value of phydev->interface (in
phy_device_create()) to be PHY_INTERFACE_MODE_NA. Move the interface
parameter to phy_connect_dev(), where it should be.
Change all occurrences treewide. In occurrences where we don't call
phy_connect_dev() for some reason (they only configure the PHY without
connecting it to an ethernet controller), set
phydev->interface = value from phy_find_by_mask call.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
|
|
Rename constant PHY_INTERFACE_MODE_NONE to PHY_INTERFACE_MODE_NA to make
it compatible with Linux' naming.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
|
|
Add helpers ofnode_read_phy_mode() and dev_read_phy_mode() to parse the
"phy-mode" / "phy-connection-type" property. Add corresponding UT test.
Use them treewide.
This allows us to inline the phy_get_interface_by_name() into
ofnode_read_phy_mode(), since the former is not used anymore.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
Some boards like the Beacon RZ/G2 SOM use either flags for
tx-internal-delay-ps, rx-internal-delay-ps or rgmii-rxid.
In Linux the APSR_RDM flag is set when either rx-internal-delay-ps
is set or the mode is rgmii-rxid, and the APSR_TDM is set when
tx-internal-delay-ps is found or rgmii-txid is set, and both
are set if rgmii-id is set.
The ravb driver in U-Boot driver was missing rgmii-rxid support,
so add that support in a similar fashion to what is done in Linux.
Signed-off-by: Adam Ford <aford173@gmail.com>
|
|
The RZ/G2 series uses an external clock as a reference to the AVB.
If this clock is controlled by an external programmable clock,
it must be requested by the consumer or it will not turn on.
In order to do this, update the driver to use bulk enable and
disable functions to enable clocks for boards with multiple clocks.
Signed-off-by: Adam Ford <aford173@gmail.com>
|
|
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This name is far too long. Rename it to remove the 'data' bits. This makes
it consistent with the platdata->plat rename.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Rename this to be consistent with the change from 'platdata'.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
We use 'priv' for private data but often use 'platdata' for platform data.
We can't really use 'pdata' since that is ambiguous (it could mean private
or platform data).
Rename some of the latter variables to end with 'plat' for consistency.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
This construct is quite long-winded. In earlier days it made some sense
since auto-allocation was a strange concept. But with driver model now
used pretty universally, we can shorten this to 'auto'. This reduces
verbosity and makes it easier to read.
Coincidentally it also ensures that every declaration is on one line,
thus making dtoc's job easier.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
The micrel phy driver is already configuring this values from
device tree. So remove the redundant phy configuration call from
this driver.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
|
|
When you enable CONFIG_OF_LIVE, you will end up with a lot of
conversions.
To generate this commit, I used coccinelle excluding drivers/core/,
include/dm/, and test/
The semantic patch that makes this change is as follows:
<smpl>
@@
expression dev;
@@
-devfdt_get_addr(dev)
+dev_read_addr(dev)
</smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
This reverts commit 5d3a21df6694ebd66d5c34c9d62a26edc7456fc7, reversing
changes made to 56d37f1c564107e27d873181d838571b7d7860e7.
Unfortunately this is causing CI failures:
https://travis-ci.org/github/trini/u-boot/jobs/711313649
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
When you enable CONFIG_OF_LIVE, you will end up with a lot of
conversions.
To generate this commit, I used coccinelle excluding drivers/core/,
include/dm/, and test/
The semantic patch that makes this change is as follows:
<smpl>
@@
expression dev;
@@
-devfdt_get_addr(dev)
+dev_read_addr(dev)
</smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Move this uncommon header out of the common header.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Move this uncommon header out of the common header.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Move this header out of the common header.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Move this header out of the common header. Network support is used in
quite a few places but it still does not warrant blanket inclusion.
Note that this net.h header itself has quite a lot in it. It could be
split into the driver-mode support, functions, structures, checksumming,
etc.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
These functions are CPU-related and do not use driver model. Move them to
cpu_func.h
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
According to the R-Car Gen3 Hardware Manual Rev 1.50 of Nov 30, 2018, the
TX clock internal delay mode isn't supported on R-Car E3 (r8a77990) or D3
(r8a77995).
Avoid setting the APSR:TDM bit on these SoCs. Moreover, only set APSR:TDM
when the DT explicitly specifies RGMII ID or TXID mode instead of setting
it unconditionally when the PHY link speed is 1000 Mbit/s.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
|
|
The recent DTs have the PHY reset GPIO in the PHY node rather than
the ethernet MAC node, support extracting the PHY reset GPIO info
from both the PHY node and ethernet MAC node.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
|