| Age | Commit message (Collapse) | Author |
|---|
|
cmn_refclk_<p/m> lines in Torrent SERDES are used for an connecting
external reference clock. cmn_refclk_<p/m> can also be configured to
output the reference clock. In order to drive the refclk out from the
SERDES (Cadence Torrent), PHY_EN_REFCLK should be set in SERDES_RST of
WIZ. Model PHY_EN_REFCLK as a clock, so that platforms like AM642 EVM
can enable it.
Based on: https://lore.kernel.org/r/20210310120840.16447-6-kishon@ti.com
Signed-off-by: George McCollister <george.mccollister@konsulko.com>
Tested-by: Bryan Brattlof <bb@ti.com>
|
|
Move the SERDES configuration check after clock and reset initialization
and change it from a hard failure to a skip of WIZ initialization. This
allows the driver to probe successfully when the SERDES has been
pre-configured by a previous boot stage (e.g., ROM or SPL).
This approach aligns with how the Linux kernel handles pre-configured
SERDES, where the driver gracefully skips reinitialization rather than
failing to probe.
Signed-off-by: Hrushikesh Salunke <h-salunke@ti.com>
|
|
In j721e_wiz_probe the test for too many lanes jumps to the error exit
path without assigning an error code which could lead to calling code
silently ignoring the failure. Set the error code.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
|
|
It is confusing to have both "$(PHASE_)" and "$(XPL_)" be used in our
Makefiles as part of the macros to determine when to do something in our
Makefiles based on what phase of the build we are in. For consistency,
bring this down to a single macro and use "$(PHASE_)" only.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Use XPL_ as the symbol to indicate an SPL build. This means that SPL_ is
no-longer set.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Remove <common.h> from this driver directory and when needed
add missing include files directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Replace instances of http://www.ti.com with https://www.ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
|
|
Enable full rate divider configuration support for J721E_WIZ_16G for SGMII.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
|
|
Select the same mac divider for SGMII too as the one being used for
QSGMII.
Enable full rate divider configuration support for J721E_WIZ_10G for
SGMII.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
|
|
Add support for j721s2-wiz-10g device to use clock-names interface
instead of explicitly defining clock nodes within device tree node.
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
|
|
The WIZ acts as a wrapper for SerDes and has Lanes 0 and 2 reserved
for USB for type-C lane swap if Lane 1 and Lane 3 are linked to the
USB PHY that is integrated into the SerDes IP. The WIZ control register
has to be configured to support this lane swap feature.
The support for swapping lanes 2 and 3 is missing and therefore
add support to configure the control register to swap between
lanes 2 and 3 if PHY type is USB.
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
|
|
It's possible that the Type-C plug orientation on the DIR line will be
implemented through hardware design. In that situation, there won't be
an external GPIO line available, but the driver still needs to address
this since the DT won't use the typec-dir-gpios property.
Add code to handle LN10 Type-C swap if typec-dir-gpios property is not
specified in DT.
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
|
|
Add support for j784s4-wiz-10g device which has two core reference
clocks (e.g core_ref_clk, core_ref1_clk) which requires an additional
mux selection option.
Signed-off-by: Matt Ranostay <mranostay@ti.com>
|
|
Move device specific data into OF data structure so it
is easier to maintain and we can get rid of if statements.
Based on: https://lore.kernel.org/linux-phy/20220526064121.27625-1-rogerq@kernel.org/T/#u
Cc: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Matt Ranostay <mranostay@ti.com>
|
|
Fix the condition for setting P_ENABLE_FORCE bit, by syncing with the
driver in kernel.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
|
|
Add support for WIZ module present in TI's J721E SoC. WIZ is a SERDES
wrapper used to configure some of the input signals to the SERDES. It is
used with both Sierra(16G) and Torrent(10G) SERDES. This driver configures
three clock selects (pll0, pll1, dig) and supports resets for each of the
lanes.
This is an adaptation of the linux driver.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210721155849.20994-10-kishon@ti.com
|
